JVC KD-S747 Bedienungsanleitung

GET0138-001A

[EE]

INSTRUCTIONS

ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ

KD-S747

CD RECEIVER

РЕСИВЕР С ПРОИГРЫBATEЛEM KOMПAKT-ДИCКOB

ENGLISH

РУCCKИЙ

For installation and

connections, refer to

the separate manual.

Указания по

установке и

выполнению

соединений

приводятся в

отдельной

инструкции.

В соответствии с Законом Российской Федерации “О за ите прав

потребителей” срок службы (годности) данного товара “по истечении

которого он может представлять опасность для жизни, здоровья

потребителя, причинять вред его иму еству или окружаю ей среде”

составляет семь (7) лет со дня производства. Этот срок является

временем, в течение которого потребитель данного товара может

безопасно им пользоваться при условии соблюдения инструкции по

эксплуатации данного товара, проводя необходимое обслуживание,

включаю ее замену расходных материалов и/или соответствую ее

ремонтное обеспечение в специализированном сервисном центре.

Дополнительные косметические материалы к данному товару,

поставляемые вместе с ним, могут храниться в течение двух (2) лет со

дня его производства.

Срок службы (годности), кроме срока хранения дополнительных

косметических материалов, упомянутых в предыду их двух пунктах, не

затрагивает никаких других прав потребителя, в частности,

гарантийного свидетельства JVC, которое он может получить в

соответствии с законом о правах потребителя или других законов,

связанных с ним.

KD-S747

COMPACT

DIGITAL AUDIO

Cover_001A_KD-S747[EE]f.p65 1/17/03, 9:33 AM3

ENGLISH

BEFORE USE

For safety....

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

Temperature inside the car....

If you have parked the car for a long time in hot or

cold weather, wait until the temperature in the car

becomes normal before operating the unit.

How to reset your unit

While holding SEL (select), press

(standby/on/attenuator) for more than 2 seconds.

This will reset the built-in microcomputer.

Notes:

• Your preset adjustments—such as preset channels or

sound adjustments—will also be erased.

• If a disc is in the unit, it will eject when you reset the

unit. Be careful not to drop the disc. SEL (select)

(standby/on/attenuator)

Position And Reproduction Of Labels

Name/Rating plate

Bottom panel of the main unit

IMPORTANT FOR LASER PRODUCTS

Precautions:

1.CLASS 1 LASER PRODUCT

2.CAUTION: Invisible laser radiation when open and

interlock failed or defeated. Avoid direct exposure to

beam.

3.CAUTION: Do not open the top cover. There are no

user-serviceable parts inside. Leave all servicing to

qualified service personnel.

4.CAUTION: This CD player uses invisible laser radiation

and is equipped with safety switches to prevent radiation

emission when unloading CDs. It is dangerous to defeat

the safety switches.

5.CAUTION: Use of controls, adjustments or performance

of procedures other than those specified herein may

result in hazardous radiation exposure.

CAUTION: Invisible laser

radiation when open and

interlock failedordefeated.

AVOID DIRECT EXPOSURE

TO BEAM. (e)

ADVARSEL: Usynlig laser-

stråling ved åbning, når

sikkerhedsafbrydere er ude

af funktion. Undgåudsæt-

telse for stråling. (d)

VARNING: Osynlig laser-

strålning när denna del är

öppnad och spärren är

urkopplad. Betrakta

strålen. (s)

VARO: Avattaessa ja

suojalukitus ohitettaessa

olet alttiina näkymättö-

mälle lasersäteilylle.

Älä katso säteeseen. (f)

Caution:

This product contains a laser component

of higher laser class than Class 1.

EN02-04_KD-S747[EE]f.p65 1/9/03, 6:06 PM2

ENGLISH

CONTENTS

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

How to reset your unit ............................... 2

How to use the M (MODE) button ............. 3

LOCATION OF THE BUTTONS ............ 4

Control panel ............................................. 4

BASIC OPERATIONS ....................... 5

Turning on the power ................................ 5

Setting the clock ........................................ 6

RADIO OPERATIONS ...................... 7

Listening to the radio ................................. 7

Storing stations in memory ....................... 8

Tuning in to a preset station ...................... 9

CD OPERATIONS ........................... 10

Playing a CD ............................................. 10

Locating a track or a particular portion

on a CD .................................................. 11

Selecting CD playback modes .................. 12

Prohibiting CD ejection ............................. 12

SOUND ADJUSTMENTS ................... 13

Selecting preset sound modes

(C-EQ: custom equalizer) ....................... 13

Adjusting the sound .................................. 14

OTHER MAIN FUNCTIONS ................ 15

Selecting the level display ......................... 15

Selecting the telephone muting ................. 15

Detaching the control panel ...................... 16

TROUBLESHOOTING ...................... 17

MAINTENANCE ............................. 18

Handling discs ........................................... 18

SPECIFICATIONS ........................... 19

How to use the M (MODE) button

If you press M (MODE), the unit goes into functions mode, then the number buttons and 5/∞buttons

work as different function buttons.

Ex.: When number button 2 works as MO (monaural) button.

To use these buttons for original functions again after pressing M (MODE), wait for 5 seconds

without pressing any of these buttons until the functions mode is cleared.

• Pressing M (MODE) again also clears the functions mode.

Time countdown indicator

EN02-04_KD-S747[EE]f.p65 1/9/03, 6:06 PM3

ENGLISH

KD-S747

LOCATION OF THE BUTTONS

Control panel

1(standby/on/attenuator) button

2SEL (select) button

3Control dial

4Display window

5Loading slot

64/¢buttons

7FM/AM button

85(up) button

+10 button

90(eject) button

p∞(down) button

–10 button

qDISP (display) button

• Also functions as SSM buttons when pressed

together with M (MODE) button.

wM (MODE) button

• Also functions as SSM buttons when pressed

together with DISP (display) button.

eMO (monaural) button

rRPT (repeat) button

tRND (random) button

yNumber buttons

uE (EQ: equalizer) button

iCD button

o(control panel release) button

Display window

;LOUD (loudness) indicator

aEQ (equalizer) indicator

sCD–in indicator

dCD indicator

fFM band indicators (FM1, FM2, FM3)

gAM band indicator

hTuner reception indicators

MO (monaural), ST (stereo)

jRND (disc random) indicator

kVolume (or audio) level indicator

lMain display

/RPT (repeat) indicator

Display window

EN02-04_KD-S747[EE]f.p65 1/9/03, 6:06 PM4

ENGLISH

BASIC OPERATIONS

Turning on the power

Turn on the power.

Note on One-Touch Operation:

When you select a source in step

below, the

power automatically comes on. You do not have

to press this button to turn on the power.

Select the source.

To operate the tuner (FM or AM),

see pages 7 – 9.

To play a CD,

see pages 10 – 12.

Adjust the volume.

Adjust the sound as you want.

(See pages 13 and 14.)

To drop the volume in a moment

Press briefly while listening to any

source. “AT T ”starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

•If you turn the control dial, you can also restore

the sound.

To turn off the power

Press and hold for more than one

second.

“SEE YOU”appears, then the unit turns off.

•If you turn off the power while listening to a

CD, CD play will start from where playback has

been stopped previously, next time you turn on

the power.

CAUTION on Volume Setting:

CDs produce very little noise compared with other

sources. If the volume level is adjusted for the

tuner, for example, the speakers may be damaged

by the sudden increase in the output level.

Therefore, lower the volume before playing a CD

and adjust it as required during playback.

To increase the volume

To decrease the volume

Volume (or audio) level indicator

(see page 15)

Volume level appears.

EN05-06_KD-S747[EE]f.p65 1/9/03, 6:07 PM5

ENGLISH

Setting the clock

Press and hold SEL (select) for more

than 2 seconds.

“CLOCK H,”“CLOCK M,”

“LEVEL,”or “TEL”appears

on the display.

Set the hour.

1Select “CLOCK H”(hour) if not shown on

the display.

2Adjust the hour.

Set the minute.

1Select “CLOCK M”(minute).

2Adjust the minute.

Finish the setting.

To check the current clock time or change the

display mode

Press DISP (display) repeatedly.

Each time you press the button,

the display mode changes as

follows:

• During tuner operation:

• During CD operation:

• During power off:

The power turns on and the clock time is

shown for 5 seconds, then the power turns off.

Frequency Clock

Elapsed playing time Clock

EN05-06_KD-S747[EE]f.p65 1/9/03, 6:07 PM6

ENGLISH

RADIO OPERATIONS

Listening to the radio

You can use either automatic searching or

manual searching to tune in to a particular

station.

Searching a station automatically:

Auto search

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

Start searching a station.

When a station is received, searching stops.

To stop searching before a station is

received, press the same button you have

pressed for searching.

Note:

FM1 and FM2: 87.5 MHz – 108.0 MHz

FM3: 65.00 MHz – 74.00 MHz

Searching a station manually:

Manual search

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

Press and hold ¢or 4

until “M” (manual) starts flashing on

the display.

To search stations of

higher frequencies

To search stations of lower

frequencies

Selected band appears.

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

FM1 FM2 FM3 AM

CONTINUED ON THE NEXT PAGE

EN07-09_KD-S747[EE]f.p65 1/9/03, 6:06 PM7

ENGLISH

To tune in to stations of

lower frequencies

To tune in to stations of

higher frequencies

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM

band (FM1, FM2, and FM3).

Select the FM band (FM1 – 3) you

want to store FM stations into.

Each time you press the

button, the band changes as

follows:

Press and hold both buttons for

more than 2 seconds.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2, or FM3).

These stations are preset in the number

buttons—No.1 (lowest frequency) to No.6

(highest frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

MO (monaural) indicator

“- -SSM- -” appears, then disappears when

automatic preset is over.

FM1 FM2 FM3 AM

Tune in to a station you want while

“M” (manual) is flashing.

• If you release your finger from the button,

the manual mode will automatically turns

off after 5 seconds.

• If you hold down the button, the frequency

keeps changing—in 50 kHz intervals

(87.5 MHz — 108.0 MHz for FM 1 and FM

2), in 30 kHz intervals (65.00 MHz — 74.00

MHz for FM 3) and 9 kHz for AM—MW/LW

until you release the button.

When an FM stereo broadcast is hard to

receive:

1Press M (MODE) to enter the

functions mode while listening

to an FM stereo broadcast.

2Press MO (monaural), while

still in the functions mode, so

that the MO indicator lights up

on the display.

Each time you press the

button, the MO indicator lights

up and goes off alternately.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

reception will be improved.

EN07-09_KD-S747[EE]f.p65 1/19/03, 9:24 AM8

ENGLISH

Manual preset

You can preset up to 6 stations in each band

(FM1, FM2, FM3, and AM) manually.

Ex.: Storing FM station of 88.3 MHz into the

preset number 1 of the FM1 band.

Select the band (FM1 – 3, AM) you

want to store stations into (in this

example, FM1).

Each time you press the

button, the band changes as

follows:

Tune in to a station (in this example,

of 88.3 MHz).

Press and hold the number button

(in this example, 1) for more than

2 seconds.

To tune in to stations of

lower frequencies

To tune in to stations of

higher frequencies

FM1 FM2 FM3 AM

Repeat the above procedure to store

other stations into other preset

numbers.

Notes:

• A previously preset station is erased when a new

station is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example,

during battery replacement). If this occurs, preset

the stations again.

Tuning in to a preset station

You can easily tune in to a preset station.

Remember that you must store stations first. If

you have not stored them yet, see “Storing

stations in memory” on pages 8 and 9.

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

Select the number (1 – 6) for the

preset station you want.

Note:

You can also use the 5(up) or ∞(down) button on

the unit to select the next or previous preset stations.

Each time you press the 5(up) or ∞(down) button,

the next or previous preset station is tuned in.

“P1” flashes for a few seconds.

FM1 FM2 FM3 AM

EN07-09_KD-S747[EE]f.p65 1/9/03, 6:06 PM9

ENGLISH

Playing a CD

Insert a CD into the loading slot.

The unit turns on, draws

the CD and starts

playback automatically.

Note on One-Touch Operation:

When a CD is already in the loading slot, pressing CD

turns on the unit and starts playback automatically.

All tracks will be played repeatedly until you stop

playback.

CD OPERATIONS

Note:

When a CD is inserted upside down, “EJECT” and

the CD–in indicator flash on the display and the CD

automatically ejects.

To stop play and eject the CD

Press 0.

CD play stops and the CD automatically ejects

from the loading slot. The source changes to the

tuner (you will hear the last received station).

• If you change the source, CD play also stops

(without ejecting the CD).

Next time you select “CD” as the source, CD

play starts from where playback has been

stopped previously.

Notes:

• If the ejected CD is not removed for about

15 seconds, the CD is automatically inserted again

into the loading slot to protect it from dust.

(CD play will not start this time.)

• You can eject the CD even when the unit is turned

off.

About mistracking:

Mistracking may result from driving on extremely

rough roads. This does not damage the unit and

the CD, but will be annoying.

We recommend that you stop CD play while

driving on such rough roads.

Elapsed playing time Current track

Total track number

of the inserted disc

Total playing time

of the inserted disc

The CD–in indicator lights up.

The CD–in indicator flashes.

EN10-12_KD-S747[EE]f.p65 1/9/03, 6:07 PM10

Andere Handbücher für KD-S747

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung