JVC KD-SHX751 Bedienungsanleitung

SERVICE MANUAL

2005/4

CD/SD RECEIVER

MA16320054

KD-SHX751

TABLE OF CONTENTS

1 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-29

KD-SHX751

PICT

SOURCE

DISP

BACK

T/P

BAND

Area suffix

E ------------- Southern Europe

EX ------------ Northern Europe

EY ------------- Eastern Europe

EU ------------------------- Turkey

1-2 (No.MA163)

SPECIFICATION

• Design and specifications are subject to change without notice.

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/

or other countries.

• SD logo is a trademark.

AUDIO AMPLIFIER SECTION

Maximum Power Output Front 52 W per channel

Rear 52 W per channel

Continuous Power Output (RMS) Front 22 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total

harmonic distortion.

Rear 22 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total

harmonic distortion.

Load Impedance 4 Ω(4 Ωto 8 Ωallowance)

Equalizer Control Range Frequencies 60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.4 kHz, 6 kHz, 12 kHz

Level ±10 dB

Frequency Response 40 Hz to 20 000 Hz

Signal-to-Noise Ratio 70 dB

Line-In Level/Impedance LINE IN 1.5 V/20 kΩload

Line-Out Level/Impedance LINE OUT 5.0 V/20 kΩload (full scale)

Output Impedance 1 kΩ

Other Terminals SUBWOOFER OUT

Changer control

Steering wheel remote input

TUNER SECTION

Frequency Range FM 87.5 MHz to 108.0 MHz

AM (MW) 522 kHz to 1 620 kHz

(LW) 144 kHz to 279 kHz

FM Tuner Usable Sensitivity 11.3 dBf (1.0 µV/75 Ω)

50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)

Alternate Channel Selectivity (400 kHz) 65 dB

Frequency Response 40 Hz to 15 000 Hz

Stereo Separation 35 dB

Capture Ratio 1.5 dB

MW Tuner Sensitivity 20 µV

Selectivity 65 dB

LW Tuner Sensitivity 50 µV

CD/SD PLAYER SECTION

Type Compact disc player

Signal Detection System Non-contact optical pickup (semiconductor laser)

Number of Channels 2 channels (stereo)

Frequency Response 5 Hz to 20 000 Hz

Dynamic Range 98 dB

Signal-to-Noise Ratio 102 dB

Wow and Flutter Less than measurable limit

MP3 (MPEG Audio Layer 3) Max. Bit Rate 320 kbps

WMA (Windows Media Audio) Max. Bit Rate 192 kbps

Playable SD Card Format FAT 12/16

Storage Up to 512 MB

Playable Audio Format for SD Card MP3/WMA

GENERAL

Power Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)

Grounding System Negative ground

Allowable Operating Temperature 0°C to +40°C

Dimensions (W ×H ×D) Installation Size (approx.) 182 mm ×52 mm ×157 mm

Panel Size (approx.) 188 mm ×58 mm ×13 mm

Mass (approx.) 1.7 kg (excluding accessories)

(No.MA163)1-3

SECTION 1

PRECAUTIONS

1.1 Safety Precautions

!Burrs formed during molding may be left over on some parts of the chassis. Therefore,

pay attention to such burrs in the case of preforming repair of this system.

!Please use enough caution not to see the beam directly or touch it in case of an

adjustment or operation check.

1-4 (No.MA163)

1.2 Preventing static electricity

Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser

diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.

1.2.1 Grounding to prevent damage by static electricity

Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.

Be careful to use proper grounding in the area where repairs are being performed.

(1) Ground the workbench

Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the

traverse unit (optical pickup) on it.

(2) Ground yourself

Use an anti-static wrist strap to release any static electricity built up in your body.

(3) Handling the optical pickup

• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical

pickup are shorted. After replacement, return the shorted parts to their original condition.

(Refer to the text.)

• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily

destroy the laser diode.

1.3 Handling the traverse unit (optical pickup)

(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.

(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the

replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a

time when attaching it to the connector.

(3) Handle the flexible cable carefully as it may break when subjected to strong force.

(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.

1.4 Attention when traverse unit is decomposed

*Please refer to "Disassembly method" in the text for the CD pickup unit.

• Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit.

(If the flexible wire is disconnected without applying solder, the CD pickup may be destroyed by static electricity.)

• In the assembly, be sure to remove solder from the short land after connecting the flexible wire.

(caption)

Anti-static wrist strap

Conductive material

(conductive sheet) or iron plate

CN601

Short sections Flexible wire

Mechanism control board

(No.MA163)1-5

1.5 Important for laser products

1.CLASS 1 LASER PRODUCT

2.DANGER : Invisible laser radiation when open and inter

lock failed or defeated. Avoid direct exposure to beam.

3.CAUTION : There are no serviceable parts inside the

Laser Unit. Do not disassemble the Laser Unit. Replace

the complete Laser Unit if it malfunctions.

4.CAUTION : The CD,MD and DVD player uses invisible

laser radiation and is equipped with safety switches which

prevent emission of radiation when the drawer is open and

the safety interlocks have failed or are defeated. It is

dangerous to defeat the safety switches.

5.CAUTION : If safety switches malfunction, the laser is able

to function.

6.CAUTION : Use of controls, adjustments or performance of

procedures other than those specified here in may result in

hazardous radiation exposure.

REPRODUCTION AND POSITION OF LABELS

Please use enough caution not to

see the beam directly or touch it

in case of an adjustment or operation

check.

WARNING LABEL

CAUTION : Visible and Invisible

laser radiation when open and

interlock failed or defeated.

AVOID DIRECT EXPOSURE TO

BEAM. (e)

VARNING : Synlig och

osynling laserstrålning när

den öppnas och spärren är

urkopplad. Betrakta ej

strålen. (s)

VARO : Avattaessa ja suojalukitus

ohitettuna tai viallisena olet alttiina

näkyvälle ja näkymättömälle

lasersäteilylle. Vältä säteen

kohdistumista suoraan itseesi. (f)

ADVARSEL : Synlig og usynlig

laserstråling når maskinen er

åben eller interlocken fejeler.

Undgå direkte eksponering til

stråling. (d)

CLASS 1

LASER PRODUCT

1-6 (No.MA163)

SECTION 2

SPECIFIC SERVICE INSTRUCTIONS

This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.

(No.MA163)1-7

SECTION 3

DISASSEMBLY

3.1 Main body section

3.1.1 Removing the front panel assembly

(See Fig.1)

(1) Push the detach button in the lower right part of the front

panel assembly.

(2) Remove the front panel assembly.

Fig.1

3.1.2 Removing the heat sink

(See Fig.2)

Reference:

Remove the front panel assembly as required.

(1) From the left side of the main body, remove the two screws

Aand two screws Battaching the heat sink.

(2) Remove the heat sink from the main body.

Fig.2

Detach button

Front panel assembly

Heat sink

AAB

1-8 (No.MA163)

3.1.3 Removing the top chassis assembly

(See Figs.3 to 6)

• Prior to performing the following procedures, remove the heat

sink.

Reference:

Remove the front panel assembly as required.

(1) From the bottom side of the main body, remove the two

screws Cattaching the top chassis assembly to the bottom

chassis assembly. (See Fig.3)

(2) From the both and rear sides of the main body, remove the

four screws Dattaching the top chassis assembly to the

bottom chassis assembly. (See Figs.4 to 6)

(3) Remove the screw Eattaching the IC heat sink to bottom

chassis assembly. (See Fig.5)

(4) Lift the top chassis assembly in the direction of the arrow,

disconnect the connector CN503 on the mechanism con-

trol board from the connector CN721 on the main board.

(See Figs.4 to 6)

(5) Take out the top chassis assembly from the bottom chassis

assembly.

Reference:

Remove the screw E' and the IC heat sink as required. (See

Fig5)

Fig.3

Fig.4

Fig.5

Fig.6

Top chassis assembly

Bottom chassis assembly

Top chassis assembly

CN503

CN721

Main board

Mechanism control board

Top chassis assembly

Bottom chassis assembly

Mechanism control board

E'E

IC heat sink

Top chassis assembly

Bottom chassis assembly Rear bracket

(No.MA163)1-9

3.1.4 Removing the front chassis assembly

(See Figs.7 and 8)

• Prior to performing the following procedure, remove the front

panel assembly, heat sink and top chassis assembly.

(1) From the both sides of the top chassis assembly, remove

the two screws Fattaching the front chassis assembly.

(2) Remove the front chassis assembly from the top chassis

assembly.

Fig.7

Fig.8

3.1.5 Removing the CD mechanism assembly

(See Fig.9)

• Prior to performing the following procedures, remove the front

panel assembly, heat sink and top chassis assembly.

Reference:

Remove the front chassis assembly as required.

(1) From the inside of the top chassis assembly, remove the

three screws Gattaching the CD mechanism assembly.

(2) Release the mecha heat sink from the slots aon the mech-

anism control board and remove the mecha heat sink from

the main body.

(3) Take out the CD mechanism assembly from the top chas-

sis.

Fig.9

Top chassis assembly

Front chassis assembly

Top chassis assembly

Front chassis assembly

Top chassis

Mecha heat sink

G G

CD mechanism assembly

Mechanism control board

1-10 (No.MA163)

3.1.6 Removing the main board

(See Figs.10 and 11)

• Prior to performing the following procedures, remove the front

panel assembly, heat sink and top chassis assembly.

(1) From the rear side of the bottom chassis assembly, remove

the two screws Hattaching the rear bracket to the bottom

chassis assembly. (See Fig.10)

(2) From the top side of the bottom chassis assembly, remove

the two screws Jattaching the main board to the bottom

chassis assembly. (See Fig.11)

(3) Release the stopper of the connector CN701 on the main

board in an upward direction, disconnect the card wire from

the connector CN701. (See Fig.11)

(4) Disconnect the wire from the connector of the front door

mechanism assembly. (See Fig.11)

(5) Disconnect the wire from the connector CN991 on the main

board. (See Fig.11)

Reference:

After connecting the wires, fix the wires with the wire

holders.

(6) Take out the main board from the bottom chassis assem-

bly.

Fig.10

Fig.11

3.1.7 Removing the rear bracket

(See Fig.12)

• Prior to performing the following procedures, remove the front

panel assembly, heat sink, top chassis assembly and main

board.

(1) From the rear side of the main board, remove the wires

from the rear bracket in the direction of the arrow.

(2) Remove the screw K, screw Land four screws Mattaching

the rear bracket to the main board.

Reference:

After attaching the rear bracket to the main board, pass the

wires through the wire holder and insert them into the slots of

the rear bracket.

Fig.12

Rear bracket

Bottom chassis assembly

Connector

Wire holders CN701

Stopper

Bottom chassis assembly

CN991

Main board

Card wire

Front door mechanism assembly

Rear bracket

M M

Main board

Wire holder

Slots

Rear bracket

Wires

Andere Handbücher für KD-SHX751

Inhaltsverzeichnis

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung