JVC KD-SX60WT Bedienungsanleitung

ENGLISH

GET0157-001A

[J]

ESPAÑOL

FRANÇAIS

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

For customer Use:

Enter below the Model No. and

Serial No. which are located on

the top or bottom of the cabinet.

Retain this information for future

reference.

Model No.

Serial No.

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

CD RECEIVER KD-SX60WT/KD-SX50M

RECEPTOR CON CD KD-SX60WT/KD-SX50M

RECEPTEUR CD KD-SX60WT/KD-SX50M

KD-SX60WT

180W

KD-SX50M

180W

COMPACT

DIGITAL AUDIO

KD-SX60WT

KD-SX50M

Cover_KD-SX60WT_50M[J]f.p65 3/26/03, 4:09 PM3

ENGLISH

*Temperature inside the car....

If you have parked the car for a long time in hot or

cold weather, wait until the temperature in the car

becomes normal before operating the unit.

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT FOR LASER PRODUCTS

Precautions:

1. CLASS 1 LASER PRODUCT

2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct

exposure to beam.

3. CAUTION: Do not open the top cover. There are no user-serviceable parts inside. Leave all

servicing to qualified service personnel.

4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches

to prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.

5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

How to reset your unit

While holding SEL (select), press

(standby/on/attenuator) for more than 2 seconds.

This will reset the built-in microcomputer.

Notes:

• Your preset adjustments—such as preset channels or

sound adjustments—will also be erased.

• If a disc is in the unit, it will eject when you reset the unit.

Be careful not to drop the disc.

(standby/on/attenuator)

SEL (select)

BEFORE USE

*For safety....

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

EN02-03_KD-SX60WT_50M[J]f.p65 3/26/03, 4:09 PM2

ENGLISH

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

CONTENTS

OTHER MAIN FUNCTIONS ................ 15

Selecting the level meter ........................... 15

Selecting the external component ............. 15

Detaching the control panel ...................... 16

CD CHANGER OPERATIONS .............. 17

About MP3 discs ....................................... 17

Playing discs ............................................. 18

Selecting the playback modes .................. 20

EXTERNAL COMPONENT

OPERATIONS ............................. 21

Playing an external component ................. 21

TROUBLESHOOTING ...................... 22

MAINTENANCE ............................. 24

Handling discs ........................................... 24

SPECIFICATIONS ........................... 25

How to reset your unit ............................... 2

How to use the M (MODE) button ............. 3

LOCATION OF THE BUTTONS ............ 4

Control panel ............................................. 4

BASIC OPERATIONS ....................... 5

Turning on the power ................................ 5

Setting the clock ........................................ 6

RADIO OPERATIONS ...................... 7

Listening to the radio ................................. 7

Storing stations in memory ....................... 8

Tuning in to a preset station ...................... 9

CD OPERATIONS ........................... 10

Playing a CD ............................................. 10

Locating a track or a particular portion

on a CD .................................................. 11

Selecting CD playback modes .................. 12

Prohibiting CD ejection ............................. 12

SOUND ADJUSTMENTS ................... 13

Selecting preset sound modes

(C-EQ: custom equalizer) ....................... 13

Adjusting the sound .................................. 14

Time countdown indicator

How to use the M (MODE) button

If you press M (MODE), the unit goes into functions mode, then the number buttons and 5/∞buttons

work as different function buttons.

Ex.: When number button 2 works as MO (monaural) button.

To use these buttons for original functions again after pressing M (MODE), wait for 5 seconds

without pressing any of these buttons until the functions mode is cleared.

•Pressing M (MODE) again also clears the functions mode.

EN02-03_KD-SX60WT_50M[J]f.p65 3/26/03, 4:09 PM3

ENGLISH

LOCATION OF THE BUTTONS

uE (EQ: equalizer) button

iCD (CD-CH: CD changer) button

o(control panel release) button

Display window

;LOUD (loudness) indicator

aEQ (equalizer) indicator

sCD–in indicator

dCD or CD-CH (CD changer) indicator

fFM band indicators (FM1, FM2, FM3)

gAM band indicator

hTuner reception indicators

MO (monaural), ST (stereo)

jVolume (or audio) level indicator

kMP3 indicator

• Lights up only when playing an MP3 disc on a

JVC MP3-compatible CD changer.

l(disc) indicator

/Main display

zRND (random) indicator

xRPT (repeat) indicator

Control panel

1(standby/on/attenuator) button

2SEL (select) button

3Control dial

4Display window

5Loading slot

64/¢buttons

7FM/AM button

85(up) button

+10 button

90(eject) button

p∞(down) button

–10 button

qDISP (display) button

• Also functions as SSM buttons when pressed

together with M (MODE) button.

wM (MODE) button

• Also functions as SSM buttons when pressed

together with DISP (display) button.

eMO (monaural) button

rRPT (repeat) button

tRND (random) button

Number buttons

Display window

EN04-04_KD-SX60WT_50M[J]f.p65 3/26/03, 4:06 PM4

ENGLISH

Adjust the sound as you want.

(See pages 13 and 14.)

To drop the volume in a moment

Press briefly while listening to any

source. “ATT” starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

• If you turn the control dial, you can also restore

the sound.

To turn off the power

Press and hold for more than one

second.

“SEE YOU”appears, then the unit turns off.

•If you turn off the power while listening to a

disc, disc play will start from where playback

has been stopped previously, next time you

turn on the power.

CAUTION on Volume Setting:

Discs produce very little noise compared with

other sources. If the volume level is adjusted for

the tuner, for example, the speakers may be

damaged by the sudden increase in the output

level. Therefore, lower the volume before playing a

disc and adjust it as required during playback.

Turning on the power

Turn on the power.

Note on One-Touch Operation:

When you select a source in step

below, the

power automatically comes on. You do not have

to press this button to turn on the power.

Select the source.

To operate the tuner (FM or AM),

see pages 7 –9.

To play a CD,

see pages 10 –12.

To operate the CD changer,

see pages 17 –20.

To operate the external component (LINE IN),

see page 21.

Adjust the volume.

BASIC OPERATIONS

Volume (or audio) level indicator

(see page 15)

Volume level appears.

To increase the volume

To decrease the volume

EN05-06_KD-SX60WT_50M[J]f.p65 3/26/03, 4:08 PM5

ENGLISH

Setting the clock

Press and hold SEL (select) for more

than 2 seconds.

“CLOCK H,”“CLOCK M,”

“LEVEL,”or “EXT IN”*

appears on the display.

*Displayed only when FM,

AM, or CD is selected as the

source.

Set the hour.

1Select “CLOCK H”(hour) if not shown on

the display.

2Adjust the hour.

Set the minute.

1Select “CLOCK M”(minute).

2Adjust the minute.

Finish the setting.

To check the current clock time or change the

display mode

Press DISP (display) repeatedly.

Each time you press the button,

the display changes as follows:

• During tuner operation:

• During CD operation:

• During CD changer operation:

• During external component operation:

• During power off:

The power turns on and the clock time is

shown for 5 seconds, then the power turns

off.

Frequency Clock

Elapsed playing time Clock

Elapsed playing time

Clock

Disc number

LINE IN Clock

EN05-06_KD-SX60WT_50M[J]f.p65 3/26/03, 4:08 PM6

ENGLISH

RADIO OPERATIONS

Listening to the radio

You can use either automatic searching or manual

searching to tune in to a particular station.

Searching for a station automatically:

Auto search

Select the band (FM 1 – 3, AM).

Each time you press the

button, the band changes as

follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

Start searching a station.

When a station is received, searching stops.

To search stations of

higher frequencies

To search stations of

lower frequencies

Selected band appears.

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

To stop searching before a station is received,

press the same button you have pressed for

searching.

Searching for a station manually:

Manual search

Select the band (FM 1 – 3, AM).

Each time you press the

button, the band changes as

follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

Press and hold ¢or 4

until “M” (manual) starts flashing on

the display.

CONTINUED ON THE NEXT PAGE

FM1 FM2 FM3 AM

EN07-09_KD-SX60WT_50M[J]f.p65 3/26/03, 4:08 PM7

ENGLISH

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM

band (FM1, FM2, and FM3).

Select the FM band (FM1 – 3) you

want to store FM stations into.

Each time you press the

button, the band changes as

follows:

Press and hold both buttons for

more than 2 seconds.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2, or FM3).

These stations are preset in the number buttons

—No.1 (lowest frequency) to No.6 (highest

frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

“- -SSM- -” appears, then disappears

when automatic preset is over.

Tune in to a station you want while

“M” (manual) is flashing.

• If you release your finger from the button,

the manual mode will automatically turns

off after 5 seconds.

• If you hold down the button, the frequency

keeps changing (in 200 kHz intervals for

FM and 10 kHz for AM) until you release

the button.

When an FM stereo broadcast is hard to

receive:

1Press M (MODE) to enter the

functions mode while listening

to an FM stereo broadcast.

2Press MO (monaural), while

still in the functions mode, so

that the MO indicator lights up

on the display.

Each time you press the

button, the MO indicator lights

up and goes off alternately.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

reception will be improved.

To tune in to stations of

higher frequencies

To tune in to stations of

lower frequencies

MO (monaural) indicator

FM1 FM2 FM3 AM

EN07-09_KD-SX60WT_50M[J]f.p65 3/26/03, 4:08 PM8

ENGLISH

Manual preset

You can preset up to 6 stations in each band

(FM1, FM2, FM3, and AM) manually.

Ex.: Storing FM station of 92.5 MHz into the

preset number 1 of the FM1 band.

Select the band (FM1 – 3, AM) you

want to store stations into (in this

example, FM1).

Each time you press the

button, the band changes as

follows:

Tune in to a station (in this example,

of 92.5 MHz).

Press and hold the number button

(in this example, 1) for more than 2

seconds.

Repeat the above procedure to store

other stations into other preset

numbers.

To tune in to stations of

higher frequencies

To tune in to stations of

lower frequencies

“P1” flashes for a few seconds.

Notes:

• A previously preset station is erased when a new

station is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example,

during battery replacement). If this occurs, preset

the stations again.

Tuning in to a preset station

You can easily tune in to a preset station.

Remember that you must store stations first. If

you have not stored them yet, see “Storing

stations in memory” on pages 8 and 9.

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

Select the number (1 – 6) for the

preset station you want.

Note:

You can also use the 5(up) or ∞(down) button on

the unit to select the next or previous preset stations.

Each time you press the 5(up) or ∞(down) button,

the next or previous preset station is tuned in.

FM1 FM2 FM3 AM

EN07-09_KD-SX60WT_50M[J]f.p65 3/26/03, 4:08 PM9

ENGLISH

CD OPERATIONS

All tracks will be played repeatedly until you stop

playback.

Note:

When a CD is inserted upside down, “EJECT” and

the CD–in indicator flash on the display and the CD

automatically ejects.

To stop play and eject the CD

Press 0.

CD play stops and the CD automatically ejects

from the loading slot. The source changes to the

previously selected source.

• If you change the source, CD play also stops

(without ejecting the CD).

Next time you select “CD” as the source, CD

play starts from where playback has been

stopped previously.

Notes:

• If the ejected CD is not removed for about 15

seconds, the CD is automatically inserted again

into the loading slot to protect it from dust.

(CD play will not start this time.)

• You can eject the CD even when the unit is turned

off.

About mistracking:

Mistracking may result from driving on extremely

rough roads. This does not damage the unit and

the disc, but will be annoying.

We recommend that you stop disc play while

driving on such rough roads.

Elapsed playing time

Total playing time

of the inserted disc

Total track number

of the inserted disc

Current track

The CD–in indicator lights up.

Playing a CD

Insert a CD into the loading slot.

The unit turns on, draws

the CD and starts

playback automatically.

Note on One-Touch Operation:

When a CD is already in the loading slot, pressing

CD (CD-CH) turns on the unit and starts playback

automatically.

The CD–in indicator flashes.

EN10-12_KD-SX60WT_50M[J]f.p65 3/26/03, 4:08 PM10

Andere Handbücher für KD-SX60WT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere JVC Autoempfänger Handbücher

JVC

JVC KW-XC550 Bedienungsanleitung

JVC

JVC KW-XC406 Bedienungsanleitung

JVC

JVC KD-MX3000R Bedienungsanleitung

JVC

JVC KD-LH2000 Bedienungsanleitung

JVC

JVC KD-G285 Bedienungsanleitung

JVC

JVC KD-G115 Bedienungsanleitung

JVC

JVC KD-AVX11 - EXAD - DVD Player Bedienungsanleitung

JVC

JVC KW-XR411 Bedienungsanleitung

JVC

JVC KD-SV203 Bedienungsanleitung

JVC

JVC GET0199-001A Bedienungsanleitung

JVC

JVC EXAD KD-AV7000 Bedienungsanleitung

JVC

JVC KD-S891R Administratorhandbuch

JVC

JVC KD-SR61 Bedienungsanleitung

JVC

JVC KD-S713R Bedienungsanleitung

JVC

JVC KD NX5000 - Navigation System With HDD Bedienungsanleitung

JVC

JVC KW-AV58 Leitfaden

JVC

JVC GET0075-001A Bedienungsanleitung

JVC

JVC KD-R300 - 30K Color-Illumination Single-DIN CD... Bedienungsanleitung

JVC

JVC KD-AVX11 - EXAD - DVD Player Bedienungsanleitung

JVC

JVC GET0321-001A Bedienungsanleitung

JVC

JVC KD-G116 Bedienungsanleitung

JVC

JVC KD-X200 Bedienungsanleitung

JVC

JVC KD-G269 Bedienungsanleitung

JVC

JVC KD-DB56 Leitfaden

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung