JVC KS-F171G Bedienungsanleitung

SERVICE MANUAL

2003/8

CASSETTE RECEIVER

MA00720038KS-F171G

TABLE OF CONTENTS

1 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2 SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

5 TROUBLE SHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17

S.BASS

SEL

DISP

Area Suffix

UN ------------- Asean

1-2 (No.MA007)

SPECIFICATION

Desain dan spesifikasi dapat berubah tanpa pemberitahuan.

BAGIAN AMPLIFIER

AUDIO Output power maksimum Depan 45 watt per chanel

Belakang 45 watt per chanel

Output Power kontinyu

(RMS) Depan 17 watt per chanel dalam 4 Ω, 40 Hz hingga 20

000 Hz dengan tidak lebih dari 0.8% distorsi

harmonis total.

Belakang 17 watt per chanel dalam 4 Ω, 40 Hz hingga 20

000 Hz dengan tidak lebih dari 0.8% distorsi

harmonis total.

Impedansi beban 4 Ω(toleransi antara 4 Ωhingga 8 Ω)

Batas tone kontrol Bass ±10 dB pada 100 Hz

Treble ±10 dB pada 10 kHz

Respon Frekuensi 40 Hz hinga 20 000 Hz

Rasio Sinyal ke suara 70 dB

Level Line-Out/ impedansi 1.0V/beban 20 kΩ(250 nWb/m)

Bagian Radio Batas Frekuensi FM 87.5 MHz hingga 108.0 MHz

AM 531 kHz hingga 1 602 kHz

[Radio FM] Sensitivitas yang dapat digunakan 11.3 dBf (1.0 µV/75 Ω)

50 dB Sensitivitas Ketenangan 16.3 dBf (1.8 µV/75 Ω)

Selektivitas Chanel Alternatif

(400 kHz) 65 dB

Respon Frekuensi 40 Hz hingga 15 000 Hz

Pemisah Stereo 35 dB

Rasio penangkapan 2.0 dB

[Radio AM] Sensitivitas 20 µV

Selektivitas 35 dB

Bagian Dek Kaset Bagian Dek Kaset 0.15% (WRMS)

Waktu Menggulung cepat 190 detik (C-60)

Respon Frekuensi 50 Hz hingga 14 000 Hz (tape normal)

Rasio Sinyal ke suara 52 dB

Pemisah Stereo 40 dB

UMUM Power yang diperlukan Tegangan Operasional DC 14.4 V

(diperbolehkan antara 11V hingga 16 V)

Sistem Grounding Ground Negatif

Temperatur kerja yang diperbolehkan 0ºC hingga +40ºC

Dimensi (L ×T ×K) Ukuran pemasangan 182 mm ×52 mm ×150 mm

Ukuran panel 188 mm ×58 mm ×11 mm

Berat 1.3 kg (tidak termasuk aksesoris)

(No.MA007)1-3

SECTION 1

PRECAUTION

1.1 Safety Precautions

!Burrs formed during molding may be left over on some parts of the chassis. Therefore,

pay attention to such burrs in the case of preforming repair of this system.

1-4 (No.MA007)

SECTION 2

SPECIFIC SERVICE INSTRUCTIONS

This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.

(No.MA007)1-5

SECTION 3

DISASSEMBLY

3.1 Main body

3.1.1 Removing the front panel assembly

(See Fig.1)

(1) Press the release button and remove the front panel as-

sembly.

Fig.1

3.1.2 Removing the bottom cover

(See Fig.2)

• Prior to performing the following procedure, remove the front

panel assembly.

(1) Turn the body upside down.

(2) Insert a screwdriver under the joints to release the two

joints aon the left side, the two joints bon the right side and

the joint con the back of the body, then remove the bottom

cover from the body.

CAUTION:

When releasing the joint cusing a screwdriver, do not damage

the board.

Fig.2

3.1.3 Removing the front chassis

(See Fig.3)

• Prior to performing the following procedure, remove the front

panel assembly and bottom cover.

(1) Remove the screw Aon each side of the body.

(2) Release the two joints dand the two joints eon the sides,

then remove the front chassis toward the front.

Fig.3

Front panel assembly

Release button

Bottom cover

Joint b

Joint c

Joint a

Joint d

Front chassis

Joint e

Joint dJoint e

1-6 (No.MA007)

3.1.4 Removing the heat sink

(See Fig.4)

• Prior to performing the following procedure, remove the front

panel assembly.

(1) Remove the screw Band two screws Cattaching the heat

sink on the left side of the body, and remove the heat sink.

Fig.4

3.1.5 Removing the rear panel

(See Fig.5 )

• Prior to performing the following procedure, remove the front

panel assembly and bottom cover.

(1) Remove the two screws D, one screw Eand three screws

Fattaching the rear panel on the back of the body.

Fig.5

3.1.6 Removing the main board

(See Fig.6)

• Prior to performing the following procedure, remove the front

panel assembly, bottom cover, front chassis, heat sink and

rear panel.

(1) Remove the two screws Gattaching the main board on the

top chassis.

(2) Disconnect the two connectors CN901 and CN721 on the

main board from the cassette mechanism assembly.

Fig.6

Heat sink

Main board

CN901

CN721

(No.MA007)1-7

3.1.7 Removing the cassette mechanism assembly

(See Fig.7)

• Prior to performing the following procedure, remove the front

panel assembly, bottom cover, front chassis, heat sink, rear

panel and main board.

(1) Remove the four screws Hattaching the cassette mecha-

nism assembly from the top chassis.

Fig.7

3.1.8 Removing the head amplifier board

(See Fig.8)

• Prior to performing the following procedure, remove the front

panel assembly, bottom cover, front chassis, heat sink, rear

panel, main board and cassette mechanism assembly.

(1) Disconnect the wire from CJ901 on the head amplifier

board.

(2) Remove the one screw Jattaching the head amplifier

board.

(3) Move the head amplifier board in the direction of the arrow

to release the two joints f, the head amplifier board can be

removed.

Fig.8

3.1.9 Removing the relay board

(See Fig.9)

• Prior to performing the following procedure, remove the front

panel assembly, bottom cover, front chassis, heat sink, rear

panel, main board and cassette mechanism assembly.

(1) Disconnect the wire from CP722 on the relay board.

(2) Remove the one screw Kattaching the relay board.

(3) Move the relay board in the direction of the arrow to release

the joint g, the relay board can be removed.

Fig.9

Top chassis

Cassette mechanism assembly

CJ901

Head amplifier board

Joint f

To head relay board

CP722

Relay board

Joint g

1-8 (No.MA007)

3.1.10 Removing the mecha bracket

(See Fig.10)

• Prior to performing the following procedure, remove the front

panel assembly, bottom cover, front chassis, heat sink, rear

panel, main board, cassette mechanism assembly, head am-

plifier board and relay board.

(1) Remove the four screws Lattaching the mecha bracket.

Fig.10

3.1.11 Removing the switch (LCD & key) board

(See Fig.11~13)

• Prior to performing the following procedure, remove the front

panel assembly.

(1) Remove the four screws Mattaching the rear cover on the

back of the front panel assembly.

(2) Release the eleven joints h, the front panel and the rear

cover become separate.

(3) Remove the switch board from the rear cover.

Fig.11

Fig.12

Fig.13

Mecha bracket

M M

Joint h

Switch (LCD & Key) board

(No.MA007)1-9

3.2 Cassette mechanism assembly

• Prior to performing the following procedures, remove the head

amplifier board, the relay board and the mechanism bracket.

3.2.1 Removing the direction switch board

(See Fig.1)

(1) Unsolder the three wires aon the direction switch board.

(2) Remove the one screw Aattaching the direction switch

board.

3.2.2 Removing the FF / REW lever assembly

(See Fig.1)

(1) Remove the screw Battaching the FF / REW lever assem-

bly on the back of the cassette mechanism assembly.

(2) Remove the screw Con the upper side of the FF / REW

lever assembly.

(3) Lift and pull forward the FF / REW lever assembly to disen-

gage the joints b, c, dand e.

3.2.3 Reattaching the FF / REW lever assembly

(See Fig.1)

(1) Reattach the FF / REW lever assembly to the joint con the

back of the chassis.

(2) Reattach the pinch-roller shaft e, the change lever dand

the return link eto the chassis.

Fig.1

3.2.4 Removing the playback head

(See Fig.2)

• Prior to performing the following procedure, remove the direc-

tion switch board and the FF / REW lever assembly.

(1) Remove the screw Dattaching the playback head.

(2) Remove the Cwasher and pull out the FF roller.

(3) Remove the Ssupport plate, the A arm spring (a) and (b),

the playback head.

ATTENTION:

The A arm spring (a) differs from the A arm spring (b).

3.2.5 Removing the pinch-roller (R) and (F) assembly

(See Fig.2)

• Prior to performing the following procedure, remove the direc-

tion switch board and the FF / REW lever assembly.

(1) Remove the P arm spring (f) in the pinch-roller (F) assem-

bly from the chassis.

(2) Remove the P arm spring (r) in the pinch-roller (R) assem-

bly from the chassis.

(3) Draw out the pinch roller (F) and (R) assembly from the

shaft.

ATTENTION:

The P arm spring (f) differs from the P arm spring (r).

ATTENTION:

The pinch roller (F) assembly differs from the pinch roller (R)

assembly.

Fig.2

FF / REW lever assembly

Joint c

Joint b

Direction switch board

Joint d

Joint e

Soldering a

A arm spring (b) A arm spring (a)

Pinch-roller (R) assembly Pinch-roller (F) assembly

Shaft Shaft

S support plate

C washer

P arm spring (f)

P arm spring (r)

Remove the P arm spring (f)

from the chassis.

Remove the P arm spring (r)

from the chassis.

Playback head

FF roller

1-10 (No.MA007)

3.2.6 Removing the cassette hanger / cassette holder

(See Fig.3)

• Prior to performing the following procedure, remove the FF /

REW lever assembly.

(1) From the rear of the unit, bend the two tabs foutwards and

disengage the two joints gin the direction of the arrow.

(2) Push the eject lever and remove the cassette holder from

the playback head. Disengage the two joints hof the cas-

sette hanger / cassette holder and the eject lever in the di-

rection of the arrow.

(3) Lift the cassette hanger / cassette holder and disengage

the joint i of the return link and the eject lever.

Fig.3

3.2.7 Removing the reel disc assembly

(See Fig.4)

• Prior to performing the following procedure, remove the FF /

REW lever assembly and the cassette hanger / cassette hold-

er.

(1) Remove the C washer and pull out reel disc assembly.

ATTENTION:

Replace with a new C washer when reattaching.

Fig.4

3.2.8 Removing the motor assembly

(See Fig.5)

(1) Unsolder the two wires jon the motor assembly.

(2) Turn over the cassette mechanism assembly and remove

the main belt and the sub-belt from the motor pulley.

ATTENTION:

The main belt can now be removed.

(3) Remove the two screws Gattaching the motor assembly.

Fig.5

Cassette holder

Cassette hanger

Return link

Joint i

Eject lever

Joint h

Joint g

Joint g Tab f

Tab f

Chassis

Reel disc assembly

C washer

Flywheel (BF)

Flywheel (BR)

Main-belt

Reel base assembly

Sub-belt

Motor assembly

Motor pulley

Soldering j

Andere Handbücher für KS-F171G

Inhaltsverzeichnis

Andere JVC Autoempfänger Handbücher

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung