JVC KS-FX202 Bedienungsanleitung
SERVICE MANUAL
CASSETTE RECEIVER
No.49682
Jan. 2002
COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD.
KS-FX202
KS-FX202
Area Suffix
E -------- Continental Europe
EX ------------Central Europe
KS-FX202
Contents
Safety precaution
Disassembly method
Adjustment method
1-2
1-3
1-12
1-16
Description of major ICs
KS-FX202
1-2
!Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Safety precaution
KS-FX202
1-3
Fig. 3
d
Front chassis
a
a
Disassembly method
Detaching the front panel unit
( See Fig.1 )
Push the Release button in the direction of arrow to
detach the front panel unit.
Removing the front chassis
( See Fig. 2 and 3 )
Disengage the four tabs ( a ) in the right and left sides of
unit and pull the front chassis forward to remove it.
Removing the bottom cover
( See Fig. 2 to 4 )
1. Removie the front chassis.
2. Turn the unit up side down.
3. Insert the screwdriver to the four engagements
( b, c, d, f ) .
4. Turn the screwdriver and remove the bottom
cover.
Fig. 1
Push the release button
Front panel unit
a
a
Fig. 2
Top chassis
Front chassis
Bottom cover
b
c
Fig. 4
f
Bottom cover
Rear panel
KS-FX202
1-4
Removing the heat sink (SeeFig.5)
1. Removing the front chassis.
2. Removing the bottom cover.
3. Remove the three screws ( 1 and 1` ) retaining the
heat sink.
Removing the main board assembly
( See Fig. 5 to 7)
1. Removing the front chassis.
2. Removing the bottom cover.
3. Removing the heat sink.
Attach the heat sink with a screw ( 1` ) on operat-
ing checks.
4. Remove the two screws ( 2 ) retaining the main
board assembly.
5. Remove the screw ( 3 ),the two screws(4) and the
four screws(5)retaining the rear panel .
6. Separate the main board assembly and cassette
mechanism assembly.
7. Take out the main board assembly.
Heat sink
Fig. 5
11
1`
Main board assembly
Fig. 6
2
2
( )
Rear panel Fig. 7
3
4
55
KS-FX202
1-5
Front cover
Front panel
Operation switch board
Fig. 9
Fig. 11
Fig. 10
Front cover
ii
i
77
77
g
h
h
h
gg
A
Removing the cassette mechanism assembly
( See Fig. 8 )
1. Removing the front chassis.
2. Removing the bottom cover.
3. Removing the heat sink.
4. Removing the main board assembly.
5. Remove the four screws ( 6 ) retaining the cassette
mechanism.
6. Separate the top chassis and cassette mechanism.
Cassette mechanism
Front side
Top chassis
Fig. 8
6
6
66
Removing the operation switch board
( See Fig. 9 to 11 )
1. Detaching the front panel unit.
2. Turn the front panel back side down.
3. Remove the four screws ( 7 ) retaining the front
cover.
4. Open the front cover gradually by disengaging the
three engagements ( g ) while pushing the top of
the front cover in the arrow "A" direction, then
disengage the three engagements ( h ) on the both
sides.
5. Place the front panel unit front side down.
6. Disengage the three engagements ( i ) on the
bottom to separate the front cover from the front
panel.
(Be careful not to lose the button springs.)
KS-FX202
1-6
Fig. 14
10
10
Chassis assembly
Removing the head amplifier board
( See Fig. 12 )
1. Removing the front chassis.
2. Removing the bottom cover.
3. Removing the heat sink.
4. Removing the main board assembly.
5. Removing the cassette mechanism.
6. Remove the screw ( 8 ) retaining the head ampli-
fier board.
7. Shift the two inter rocking sections ( j ) securing
the head amplifier board in the direction shown by
the arrow "B" to remove the printed circuit board.
8. From the connector CJ901 on the head amplifier
board from connector wire out going to the head
relay board.
Removing the chassis assembly
( See Fig. 13 and 14 )
1. Removing the front chassis.
2. Removing the bottom cover.
3. Removing the heat sink.
4. Removing the main board assembly.
5. Removing the cassette mechanism.
6. Removing the head amplifier board.
7. Turn the left side to cassette mechanism.
8. Remove the screw ( 9 ) retaining the relay board.
9. Shift the one inter rocking sections ( k ) securing
the relay board in the direction shown by the
arrow "C" to remove the printed circuit board.
10. Turn the back side down, remove the four screws
( 10 ) retaining the chassis assembly.
Fig. 12
To head relay board
Head amplifier board
CJ901
8
j
j
B
Fig. 13
Relay board
C
9k
10
10
KS-FX202
1-7
Prior to performing the following procedures, remove
the head amplifier board, the relay board and the
mechanism bracket.
<Cassette mechanism assembly>
Unsolder the three wires aon the direction switch
board.
Remove the one screw Aattaching the direction
switch board.
1.
2.
Removing the direction switch board
(See Fig.1)
Remove the screw Battaching the FF / REW lever
assembly on the back of the cassette mechanism
assembly.
Remove the screw Con the upper side of the FF /
REW lever assembly.
Lift and pull forward the FF / REW lever assembly to
disengage the joints b, c, dand e.
1.
2.
3.
Removing the FF / REW lever assembly
(See Fig.1)
Reattach the FF / REW lever assembly to the joint c
on the back of the chassis.
Reattach the pinch-roller shaft e, the change lever d
and the return link eto the chassis.
1.
2.
Reattaching the FF / REW lever assembly
(See Fig.1)
C
FF / REW lever assembly
Joint c
Joint b
B
A
Direction switch board
Joint d
Joint e
Soldering a
Fig.1
KS-FX202
1-8
Prior to performing the following procedure, remove
the direction switch board and the FF / REW lever
assembly.
Remove the screw Dattaching the playback head.
Remove the C washer and pull out the FF roller.
Remove the S support plate, the A arm spring (a)
and (b), the playback head.
1.
2.
3.
Removing the playback head (See Fig.2)
The A arm spring (a) differs from the A
arm spring (b).
ATTENTION:
Prior to performing the following procedure, remove
the direction switch board and the FF / REW lever
assembly.
Remove the P arm spring (f) in the pinch-roller (F)
assembly from the chassis.
Remove the P arm spring (r) in the pinch-roller (R)
assembly from the chassis.
Draw out the pinch roller (F) and (R) assembly from
the shaft.
1.
2.
3.
Removing the pinch-roller (R) and (F)
assembly (See Fig.2)
The P arm spring (f) differs from the P
arm spring (r).
ATTENTION:
The pinch roller (F) assembly differs
from the pinch roller (R) assembly.
ATTENTION:
A arm spring (b) A arm spring (a)
Pinch-roller (R) assembly Pinch-roller (F) assembly
Shaft Shaft
S support plate
D
C washer
P arm spring (f)
P arm spring (r)
Remove the P arm spring (f)
from the chassis.
Remove the P arm spring (r)
from the chassis.
Playback head
FF roller
Fig.2
KS-FX202
1-9
Prior to performing the following procedure, remove
the FF / REW lever assembly.
From the rear of the unit, bend the two tabs f
outwards and disengage the two joints gin the
direction of the arrow.
Push the eject lever and remove the cassette holder
from the playback head. Disengage the two joints h
of the cassette hanger / cassette holder and the eject
lever in the direction of the arrow.
Lift the cassette hanger / cassette holder and disengage
the joint iof the return link and the eject lever.
1.
2.
3.
Removing the cassette hanger / cassette
holder (See Fig.3)
Unsolder the two wires jon the motor assembly.
1.
Turn over the cassette mechanism assembly and
remove the main belt and the sub-belt from the
motor pulley.
2.
Remove the two screws Gattaching the motor
assembly.
3.
Removing the motor assembly
(See Fig.5)
To replace the sub-belt, remove the
main belt and the sub-belt from the
motor pulley. Then remove the three
screws Eand one screw F. Replace
with a new sub-belt while lifting the reel
base assembly slightly.
ATTENTION:
Prior to performing the following procedure, remove
the FF / REW lever assembly and the cassette
hanger / cassette holder.
Remove the C washer and pull out reel disc assembly.
1.
Removing the reel disc assembly
(See Fig.4)
Replace with a new C washer when
reattaching.
ATTENTION:
The main belt can now be removed.
ATTENTION:
Cassette holder
Cassette hanger
Return link
Joint i
Eject lever
Joint h
Joint h
Joint g
Joint g Tab f
Tab f
Reel disc assembly
Flywheel (BF)
Flywheel (BR)
E
E
E
F
G
G
Main-belt
Reel base assembly
Sub-belt
Motor assembly
Motor pulley
Soldering j
Fig.3
Fig.4
Fig.5
C washer
C washer
Chassis
KS-FX202
1-10
Raise the part kof the reel base assembly slightly
and remove the selector link (B) on the front side of
the cassette mechanism assembly by turning it as
shown in Fig.10.
Remove the three screws Eand the one screw F
on the underside of the cassette mechanism
assembly.
1.
2.
Removing the reel base assembly
(See Fig.5 and 6)
Prior to performing the following procedure, remove
the cassette hanger / cassette holder.
From the upper side of the cassette mechanism
assembly, remove the C washer from each shaft of
the flywheel (BF) and (BR).
Turn over the cassette mechanism assembly and
remove the main belt. Pull out the flywheel (BF) and
(BR) downward respectively.
1.
2.
Removing the Flywheel (BF) and (BR)
assembly (See Fig.4 and 5)
The reel base assembly is not
repairable. Handle with care.
ATTENTION:
Selector link (B).
Inside of the reel base assembly
Reel disc assembly
Flywheel (BF)
Flywheel (BR)
E
E
E
F
G
G
Main-belt
Reel base assembly
Sub-belt
Motor assembly
Motor pulley
Soldering j
Fig.4
Fig.5
Fig.6Fig.7
C washer
C washer
Pinch-roller (R) assembly
Turn the selector link (B).
k
Andere Handbücher für KS-FX202
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere JVC Autoempfänger Handbücher
JVC
JVC KD-X472DBT Bedienungsanleitung
JVC
JVC KD-S640 Bedienungsanleitung
JVC
JVC KD-S735R Bedienungsanleitung
JVC
JVC KD-S640 Bedienungsanleitung
JVC
JVC KDA605 - KD Radio / CD Bedienungsanleitung
JVC
JVC LVT1311-003A Bedienungsanleitung
JVC
JVC KD-R890BT Bedienungsanleitung
JVC
JVC KD-S670 Bedienungsanleitung
JVC
JVC KD-SH9101 Bedienungsanleitung
JVC
JVC GET0075-001A Bedienungsanleitung
JVC
JVC KD-DV5302 Leitfaden
JVC
JVC KD-G465 Bedienungsanleitung
JVC
JVC KD-G456 Leitfaden
JVC
JVC Car Cassette Deck KS-F500 Bedienungsanleitung
JVC
JVC KD-G351 Bedienungsanleitung
JVC
JVC KD-APD89 Bedienungsanleitung
JVC
JVC KD-G384 Bedienungsanleitung
JVC
JVC KD-SX995 Bedienungsanleitung
JVC
JVC KD-AVX40 - DVD Player With LCD monitor Bedienungsanleitung
JVC
JVC KW-V640BT Handbuch
Beliebte Autoempfänger Handbücher anderer Marken
Sound Storm
Sound Storm STM93R Bedienungsanleitung
Soundstream
Soundstream VIR-5000 Bedienungsanleitung
Avson
Avson MKT Platform Bedienungsanleitung
Sony
Sony MEX-1HD - Audio Library System Bedienungsanleitung
Pioneer
Pioneer DVH-P500UB Bedienungsanleitung
Blaupunkt
Blaupunkt SANTIAGO CR 87 Bedienungsanleitung
