Kaba Keyscan WSSKP-1 Betriebsanleitung

WSSKP-1

Installation & Programming Guide

The WSSKP-1 keypad provides an alternative to card readers and may be connected to any

Keyscan control unit or other manufacturer’s control unit that supports a Wiegand standard

26-bit format as an input signal. The WSSKP-1 can also be used conjointly with a proximity

reader. Generally, this applies to a retro-fit where a keypad or reader already exists. The

WSSKP-1 has standalone capabilities storing up to 28 PIN codes, which can be used to

activate an alarm panel for arming and disarming, locking and unlocking a door, or

triggering a video surveillance system. You may use the keypad for both a Wiegand signal

and a digital output. The WSSKP-1 is a rugged, water-resistant, stainless steel unit and

may be installed indoors or outdoors.

Keyscan Operation

The WSSKP-1 out of the box is configured for operation with a Keyscan system and does

not require changing the factory defaults. If using the WSSKP-1 for a standalone

application, refer to Operational Modes and Program Codes.

Contents

Parts List

Features

WSSKP-1

Installation & Connections

Operation Modes & Codes

Enter/Exit Program Mode

Setting Keypad Modes

User PIN Codes Table

Keypad Operation

Specifications

WSSKP-1

Keyscan Inc. A Member of the Kaba Group

Features

2 types of Wiegand outputs

Digital output triggering –standalone operation

Duress code

3 to 5 digit PIN codes

Wall switch dimensions

Braille keys

Stainless-steel finish

The unit may produce various outputs such as:

Keyscan proprietary Wiegand format when connected to a Keyscan controller

Standard 26 bit Wiegand format when connected to another manufacturer’s

controller.

Standalone operation with digital output triggering which may be used to activate

relay or door locking hardware to a maximum load current of 500 mA at 12 VDC.

Installation/Connections

The WSSKP-1 is suitable for indoor or outdoor installations. The keypad circuit board and

electronics are “water-resistant”. However, if you are installing the WSSKP-1 outside,

mount it in a plastic housing to protect the keys from possible water seepage. Do not caulk

along the bottom of the WSSKP-1 so that any water accumulation can drain out the

bottom.

Please be sure to observe and comply with the following conditions when locating and

mounting the WSSKP-1:

Do not run keypad cables in the same conduit with AC power or signal cables.

Keep keypad cables at a minimum distance of 12 inches or 30 centimetres from AC,

computer data, telephone data, or electric lock cables.

Do not install keypads within 3.5 feet or 1.1 metres of computer CRT-type monitors.

Do not install readers in areas where broad spectrum EMI noise may be present.

Devices such as motors, pumps, generators, and AC switching relays can create EMI

noise.

Important

Keypads made by other manufacturers may not have the necessary Wiegand interface.

Hence the WSSKP-1 keypads will not operate in dual card and PIN modes; they will only

operate in card/reader simulation.

WSSKP-1 Installation & Programming Guide

Figure 1 - Mounting the WSSKP-1

ABC 3

DEF

GHI 5

JKL 6

MNO

PRS 8

TUV 9

WXY

OPER

Silicone Caulking along Top

Silicone Caulking along Side

Do not caulk along bottom.

Note

Silicone caulking is

only required on

outdoor installations.

KI-00295E-07-11

Keyscan Inc. A Member of the Kaba Group

Figure 2 - WSSKP-1 Standalone Operation/Powered by Separate Supply

Brown

White

Green

Brown, White

& Green not

connected.

Isolate with

electrical tape.

Blue +

Orange

Door

Strike

COR

Orange

Blue Blue

Black -

DC power supply

Grey

KI-00296E-07-11

Diagram Notes on WSSKP-1

Orange wire in keypad is used for negative digital trigger for a third party device such as a

relay or a lock. If using the orange wire, it is triggered from local PIN stored in keypad

memory. The keypad memory stores 28 Personal Identification Numbers.

WSSKP-1 Installation & Programming Guide

Figure 3 - WSSKP-1 for Wiegand Operation Only /Powered by ACU

Brown

White

Green

Blue

Black

Shield not connected.

Isolate with

electrical tape.

Shield

ACU Ground

Lug

Brown

White

Green

Blue

Black

6 conductors shielded 22 AWG

Maximum - 500 ft (152.4 m)

Orange

to third party

device or tape

back.

Reader terminal on control board

LED D1

WHT D0

GRN PWR

RED GND

BLK

(BEEP)

KI-00214E-07-11

Diagram Notes on WSSKP-1

If orange wire is not used, tape back. See Figure 2 for connections with third party devices.

Keyscan Inc. A Member of the Kaba Group

Figure 4 –Keypad/Proximity Reader Combination

Brown

White

Green

Red

Black

Shield not

connected.

Isolate with

electrical tape.

Shield

ACU Ground

Lug

Brown

White

Green

Red

Black

6 conductors shielded 18 AWG

500 ft (152.4 m) maximum

Brown

White

Green

Blue

Red

Green

Black

Keypad

Reader

Orange

to third party

device or

tape back

KEYSCAN

Reader terminal on control board

LED D1

WHT D0

GRN PWR

RED GND

BLK

(BEEP)

KI-00215E-07-11

Diagram Notes on WSSKP-1/Reader Combination

The diagram above generally applies to a retro-fit where either a reader or keypad is

already installed. If a reader/keypad combination is required on a new installation consider

Keyscan’s K-KPR reader/keypad.

WSSKP-1 Installation & Programming Guide

Operational Modes and Program Codes

The WSSKP-1 can be used in one of three operating modes:

Standalone

Wiegand

Combined standalone/Wiegand

The following table indicates applicable Program Codes for each of the Operational Modes.

Program Codes / Code Options / Operation Modes Chart

Program

Code

Program Code Options

Standalone

Operation

Wiegand

Operation

Combined

Operation

Code 0 –

Combination

Outputs

0 =

Wiegand and digital

output on valid PIN –

# key not required

after PIN entry

(Default)



1 =

Wiegand and digital

output on valid PIN -

# key required after

PIN entry

2 =

Wiegand or digital

output on valid PIN –

# key not required

after PIN entry

3 =

Wiegand or digital

output on valid PIN –

# key required after

PIN entry

Code 1 –

Wiegand

Format

26 = 26 bit Wiegand format

36 = Keyscan proprietary

format (Default)



Code 2 –

Facility

Code

0 to 255

0 (Default)



Code 3 –

Master Code

1 to 9999

9571 (Default)



Code 5 –

Digital

Output

Status

0 = Switched Off –Normally

Open (Default)

1 = Switched On –Normally

Closed



Code 6 –

Digital

Output Time

0 to 255 seconds

5 seconds (Default)



Code 7 –

Digit Length

of PIN

3 to 5 digits

5 digits (Default)



Keyscan Inc. A Member of the Kaba Group

Program Codes / Code Options / Operation Modes Chart

Codes 8 to

62 –PINs

1 to 65535 (See table 3 to

record the 28 standalone user

PINs.)



Restore Default Settings: 2 + 0 Keys

Clear PINs: 6 + 4 Keys

How to Enter and Exit Keypad Programming Mode

The keypad may be modified for various feature selections as listed in the table Program

Codes / Code Options / Operation Modes Chart. To modify any keypad feature, first you

must enter the keypad’s programming mode and enter your master code as outlined

below.

Steps to Enter Keypad Programming Mode

1. Press and hold the * (star) key and the 1 key on the keypad until you hear a double

beep.

2. Enter your master code followed by the # key.

The default master code is 9571. This code may be altered. See Code 3 under

Setting Keypad Modes.

3. If the code is entered correctly, you will hear three beeps indicating you have entered

programming mode. If not, repeat the previous steps.

For entering specific programming codes refer to Setting Keypad Modes on the following

pages.

After you have entered programming mode and completed any required changes, you

must exit the keypad’s programming mode to resume normal keypad operation.

Steps to Exit Keypad Programming Mode

1. Press and hold the # key until you hear the double beep.

2. You have now exited programming mode.

WSSKP-1 Installation & Programming Guide

Setting Keypad Modes

The following sub-sections review code definitions and site an example of how to program

that code into the WSSKP-1 keypad. Always refer to the Program Codes / Code Options /

Operation Modes Chart to ensure the code is applicable for the keypad operation you are

configuring –standalone, Wiegand, or combined.

Code 0 - Output Combinations

The keypad may be programmed for Wiegand and digital output combinations using and/or

conditions.

Option 0 (zero) default - Wiegand and digital output generated on a valid PIN. This

option does not require pressing the # key after a valid PIN entry.

Option 1 - Wiegand and digital output generated on valid PIN. This option requires

pressing the # key after a valid PIN entry.

Option 2 - Wiegand or digital output generated on a valid PIN. This option does not

require pressing the # key after a valid PIN entry.

Option 3 - Wiegand or digital output generated on a valid PIN. This option requires

pressing the # key after a valid PIN entry.

Note

When selecting the keypad for an ‘or’ condition – Options 2 and 3 –the PIN entered will

determine a Wiegand or digital output depending on whether you have stored the user PIN

in Codes 8 to 62. If the PIN number(s) were stored in the keypad, the keypad will transmit

a digital output. If you have not stored the PIN number(s) in the keypad, the unit will

transmit a Wiegand output only.

Steps to Program Output Combinations

The following example illustrates setting Code 0 to option 1 - Wiegand and digital output

generated on valid PIN entry. This option requires pressing the # key after a valid PIN

entry.

1. Set the keypad for programming mode. See page 8.

2. Press the * (star) key, then press the 0 (zero) key on the keypad.

3. Then press the # key followed by the 1 (one) key on the keypad.

4. Then press the # key. Three beeps confirm the code has been programmed.

If three beeps are not heard, repeat the preceding steps.

5. Exit programming mode by pressing and holding the # key until you hear the double

beep.

Code 1 –Wiegand Bit Format

This feature determines the Wiegand bits transmitted from the WSSKP-1 keypad as an

output when directly wired to an access control unit (ACU).

Option 36 - Keyscan 36 bit proprietary format (default)

Option 26 - standard Wiegand 26 bit format

Keyscan Inc. A Member of the Kaba Group

Steps to Change the Wiegand Bit Format

The following example illustrates setting Code 1 to the Wiegand 26 bit format.

1. Set the keypad for programming mode. See page 8.

2. Press the * (star) key, then press the 1 key on the keypad.

3. Then press the # key followed by the 2 and 6 keys on the keypad.

4. Then press the # key. Three beeps confirm the code has been programmed.

If three beeps are not heard, repeat the preceding steps.

5. Exit programming mode by pressing and holding the # key until you hear the double

beep.

Code 2 –Facility Code

This feature determines the Wiegand facility code produced on a valid PIN entry. A facility

code is a portion of the Wiegand signal transmitted from the keypad. The facility code can

also be referred to as a batch code or a site code.

default facility code = 0 (zero)

facility code range: 0 to 255

facility code is generated as an output

Steps to Change the Facility Code

The following example illustrates setting Code 2 to a facility code of 100.

1. Set the keypad for programming mode. See page 8.

2. Press the * (star) key, then press the 2 key on the keypad.

3. Then press the # key followed by the 1, 0 (zero), 0 (zero) keys on the keypad.

4. Then press the # key. Three beeps confirm the code has been programmed.

If three beeps are not heard, repeat the preceding steps.

5. Exit programming mode by pressing and holding the # key until you hear the double

beep.

Code 3 - Default Master Code

This feature allows re-programming the master code or installer’s code in the keypad.

default master code –9571

master code range - 1 to 9999

Note

Always document a new master code entry if altered. Space is provided below the example

instructions.

Steps to Change the Master Code

The following illustrates an example of changing the master code to 1111.

1. Set the keypad for programming mode. See page 8.

2. Press the * (star) key followed by the 3 key on the keypad.

3. Press the # key followed by the 1, 1, 1, 1 keys on the keypad.

4. Then press the # key. Three beeps confirm the code has been programmed.

If three beeps are not heard, repeat steps.

Inhaltsverzeichnis

Andere Kaba Tastenfeld Handbücher

Kaba

Kaba LA GARD 5715 Betriebsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung