Kaba Simplex 3000 Series Bedienungsanleitung

Drive Assembly Installation Instructions

SIMPLEX®3000 SERIES

ackage Contents:

Tools Required For Installation

(1) drive assembly

(1) cam plug (Adams-Rite #4580)

(1) cardboard template

(1) cam plug cover (31/32" backset only)

(2) mounting screws 10-24 thd x 11/2"

(2) threaded sex nuts

(2) mounting bushings

• tape

• electric drill (variable speed recommended)

• small flat head screwdriver

• medium flat head screwdriver

• large phillips head screwdriver

• center punch

• (31/32") drill bit

• (3/8") drill bit

• (7/8") hole saw

• (1/8") drill bit

• (1/4") drill bit

• hammer

• deburring tool

• safety goggles

TABLE OF CONTENTS

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Tools Required for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

A. Hardware Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Cam Plug Handing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

B. Stile Preparation for Combination Side of Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

C. Stile Preparation for Trim Plate Side of Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

D. Drill Lock and Trim Plate ounting Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

E. Hardware Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Warnings and Cautions

Important: Carefully inspect windows, doorframe, door, etc. to ensure that

the recommended procedures will not cause any damage. Kaba Access

Control’s warranty does not cover damages caused by installation.

Caution: Wear safety glasses when preparing door.

A. HARDWARE DISASSEMBLY

A-1 Remove Adams-Rite face plate from

edge of door exposing the cylinder set

screws (See Figure 1).

A-2 Loosen the cylinder set screw (securing

key cylinder to Adams-Rite latch) and

remove the mortise cylinder from the

dead latch assembly (See Figure 1).

A-3 With the exception of the Adams-Rite dead

latch assembly, remove all other hardware

from door: knob, handle, etc (See Figure 1).

CAM LUG HANDLING

A-4 Determine the required handing of cam

disc on Adams-Rite cam plug #4580 (See

Figure 2). Looking at the edge of the door,

determine on which side the lock is to be

installed.

Note: Factory cam plug handing is RH.

If the cam disc handing needs to be changed, proceed with steps A to D.

If not, proceed to Section B-1.

A. Remove the retainer clip from the pivot pin.

B. Pull the cam pivot pin out of the disc.

Note: Do not remove the driver piece.

C. Turn the cam over and push the cam pivot pin through the cam and

into the disc.

D. Reinstall the retainer clip onto the cam pivot pin.

FIGURE 1

Narrow

Stile

Adams-Rite

Dead Latch

Assembly

Adams-Rite Face Plate

Adams-Rite

Cam Plug in

Cylinder Hole

Part #4580

Adams-Rite

Cam Plug

Part #4580

(Backside)

ortise

Cylinder

Set Screw

FIGURE 2

IF IT IS TO BE

THIS SIDE

THE CA DISC

SHOULD BE HANDED

AS SHOWN BELOW

IF IT IS TO BE

THIS SIDE

THE CA DISC

SHOULD BE HANDED

AS SHOWN BELOW

B. STILE RE ARATION FOR COMBINATION SIDE OF

DOOR

B-1 Install Adams-Rite cam plug

#4580 to the Adams-Rite dead

latch. Snug tighten the cylinder

set screw (See Figure 1). See

Section E-1 for final screw

adjustment .

B-2 Position the cardboard template

(locate on cam plug pins) as

shown (See Figure 3). Align

template such that it is parallel to

the stile of the door.

Note: It may be necessary to further

loosen the cylinder set screw referred

to in Section A-2 allowing movement

of the template. Secure template to

the stile using tape.

B-3 Center punch templates holes

marked A, B and C (See Figure 3).

B-4 Carefully remove cardboard

template (to be used again in

Section C-1). Drill pilot holes

marked A, B and C using a .094

(3⁄32") diameter drill bit (See

Figure 4).

Note: Drill through lock side of

door only. (Wear safety goggles

when drilling.)

FIGURE 3

FIGURE 4

Narrow

Stile

Adams-Rite

Dead Latch

Assembly

Adams-Rite

Face Plate

Adams-Rite

Cam Plug

Part #4580

Cardboard Template

31⁄32" B.S.—R.H.

Part #64145

31⁄32" B.S.— L.H.

Part #64146

11⁄8" B.S.—R.H.

Part #64143 (shown)

11⁄8" B.S.—L.H.

Part #64144

Cylinder

Set Screw

Cardboard

Template

Parallel to

Stile

Combination Lock Side

Narrow

Stile

Adams-Rite

Dead Latch

Assembly

Adams-Rite

Face Plate Adams-Rite

Cam Plug

Part #4580

.094 3⁄32"

Clear Drilled

Pilot Holes

.094 3⁄32"

Clear Drilled

Pilot Holes

Cylinder

Set Screw

C. STILE RE ARATION FOR TRIM LATE SIDE OF DOOR

(Trim plate assembly is included in lock

housing box marked 3001 or 3002).

C-1 Secure an Adams-Rite cam plug

#4580 to the trim plate side of the

dead latch assembly.

Note: Installation of this cam plug will

require the opposite handing as used on

the combination lock side of the door. In

the event opposite handing is required,

reverse cams as detailed in Section A.

C-2 Align and center punch holes using

the cardboard template as done in

Sections B-2 and B-3 on the

combination lock side. Position the

cardboard template as shown (See

Figure 5). ( ake sure the inside

trim plate imprint of template is

exposed.) Center punch A, B and C

holes. If obstructing hardware exists,

cut cardboard template to allow for

flush seating against stile.

C-3 Remove cardboard template. Drill

pilot holes marked A, B and C using

a .094 (3⁄32") diameter drill bit (See

Figure 6).

FIGURE 6

FIGURE 5

Narrow

Stile

Trim late Side

Adams-Rite

Cam Plug Pins

.094 3⁄32"

Pilot Holes

.094 3⁄32"

Pilot Holes

7⁄8" Clear

Drilled Hole

3⁄8" Clear

Drilled Hole

Cylinder

Set Screw

Cylinder

Set Screw

Cardboard

Template

Parallel to

Stile

KABA SIM LEX®

LIMITED WARRANTY

Kaba Access Control warrants this product to be free from defects in material

and workmanship under normal use and service for a period of one (1) year.

Kaba Access Control will repair or replace, at our discretion, locks found by Kaba

Access Control analysis to be defective during this period. Our only liability,

whether in tort or in contract, under this warranty is to repair or replace

products that are returned to Kaba Access Control within the one (1) year

warranty period.

This warranty is in lieu of and not in addition to any other warranty or condition,

express or implied, including without limitation merchantability, fitness for

purpose or absence of latent defects.

ATTENTION: This warranty does not cover problems arising out of improper

installation, neglect or misuse. All warranties implied or written will be null and

void if the lock is not installed properly and /or if any supplied component part is

substituted with a foreign part. If the lock is used with a wall bumper, the

warranty is null and void. If a doorstop is required, we recommend the use of a

floor secured stop.

The environment and conditions of use determine the life of finishes on Kaba

Access Control products. Finishes on Kaba Access Control products are subject

to change due to wear and environmental corrosion. Kaba Access Control cannot

be held responsible for the deterioration of finishes.

Authorization to Return Goods

Returned merchandise will not be accepted without prior approval. Approvals

and Returned Goods Authorization Numbers (RGA Numbers) are available

through our Customer Service department in Winston-Salem, NC 800.849.8324.

The serial number of a lock is required to obtain this RGA Number. The

issuance of an RGA does not imply that a credit or replacement will be issued.

The RGA number must be included on the address label when material is

returned to the factory. All component parts including latches and strikes (even

if not inoperative) must be included in the package with return. All merchandise

must be returned prepaid and properly packaged to the address indicated.

KABA ACCESS CONTROL

2941 INDIANA AVENUE

WINSTON-SALE , NC 27199-3770

NO POSTAGE

NECESSARY

IF AILED

IN THE

UNITED STATES

BUSINESS RE LY MAIL

FIRST-CLASS AIL PER IT NO. 1563

POSTAGE WILL BE PAID BY ADDRESSEE

WINSTON-SALE , NC

Thank you for purchasing our product. In order to

protect your investment and to enable us to better

serve you in the future, please fill out this registration

card and return it to Kaba Access Control, or

This lock will be used in what type of facility?

Commercial Building Industrial/ anufacturing Airport

College/University Government/ ilitary School/Educational

Hospital/Healthcare Other (please specify)

What area is being secured with this lock? (e.g. Front Door, Common Door, Exercise Room)

This lock is:

New Installation

Replacing a conventional keyed lock

Replacing a Kaba echanical Pushbutton Lock

Replacing a Kaba Electronic Access Control

Replacing a Keyless Lock other than Kaba

How did you learn about Kaba Access Control ushbutton Locks?

Advertisement Previous Use Internet/Web Another Use

Locksmith aintenance Training Class Other (please specify)

What was your reason for buying this lock?

Who installed your lock?

Locksmith aintenance Other

Check here if you would like more information on Kaba Access Control locks.

Name

Position

Company

Address

City

State ZIP (Postal Code) Country

Phone

Name of Dealer Purchased From

Date of Purchase

Lock odel Number

REGISTRATION CARD

Notes

D. DRILL LOCK AND TRIM

LATE MOUNTING HOLES

D-1 Remove Adams-Rite cam plug(s)

and Adams-Rite dead latch assembly

from door (See Figure 7). (This will

prevent chips from entering the

latch.)

D-2 You are now ready to enlarge pilot

holes marked A, B and C on both sides

of stile. Enlarge holes to sizes as

follows: (See Figure 8). Enlarge 2

holes marked A to a .375 diameter

(3⁄8") drill bit. Enlarge the 2 holes

marked C to a .250 diameter (1⁄4") drill

bit. Enlarge 1 hole marked B to a .875

(7⁄8") drill bit. ake sure that all holes

are deburred prior to hardware

assembly.

FIGURE 8

Trim late Side

1⁄4" Clear

Drilled Hole

7⁄8" Clear

Drilled Hole

3⁄8" Clear

Drilled Hole

Cylinder

Set Screw

FIGURE 7

Narrow

Stile

Adams-Rite

Dead Latch

Assembly

Adams-Rite Face Plate

Adams-Rite

Cam Plug in

Cylinder Hole

Part #4580

Adams-Rite

Cam Plug

Part #4580

(Backside)

ortise

Cylinder

Set Screw

Inhaltsverzeichnis

Andere Kaba Sperren Handbücher

Kaba

Kaba SIMPLEX LD450 Bedienungsanleitung

Kaba

Kaba Generation E-760 AUTO DEADBOLT ASM Office Bedienungsanleitung

Kaba

Kaba E-PLEX 2000 Bedienungsanleitung

Kaba

Kaba 1546-K5 Bedienungsanleitung

Kaba

Kaba ilco 760 Montageanleitung

Kaba

Kaba PowerLever PROX 9000 Bedienungsanleitung

Kaba

Kaba SIMPLEX L1000 Series Bedienungsanleitung

Kaba

Kaba SIMPLEX 900 Series Bedienungsanleitung

Kaba

Kaba Simplex 8100 Series Bedienungsanleitung

Kaba

Kaba SIMPLEX EE1000 Series Bedienungsanleitung

Kaba

Kaba LA GARD COMBOGARDPRO Bedienungsanleitung

Kaba

Kaba Simplex 6200 Series Bedienungsanleitung

Kaba

Kaba Simplex 1000 Series Installationsanleitung

Kaba

Kaba Combi B 30 Bedienungsanleitung

Kaba

Kaba Quantum Series Bedienungsanleitung

Kaba

Kaba Simplex Mechanical Pushbutton Locks Bedienungsanleitung

Kaba

Kaba Simplex 6200 Series Bedienungsanleitung

Kaba

Kaba C-lever compact Bedienungsanleitung

Kaba

Kaba C-lever compact Bedienungsanleitung

Kaba

Kaba Confidant RFID Kit 1 Bedienungsanleitung

Kaba

Kaba Saflok QuantumII MT RFID Bedienungsanleitung

Kaba

Kaba Simplex 1000 Series Bedienungsanleitung

Kaba

Kaba 4000 Bedienungsanleitung

Kaba

Kaba LA GARD 1947 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung