KanexPro EXT-PROCTRL Bedienungsanleitung

VER 1.0

MPN: EXT-PROCTRL

Flexible Matrix System Controller powered

by SDVoE w/ POE & RS-232

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment

and before connecting the power supply. Please keep the following in mind as you unpack

and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire,

• electrical shock and injury to persons.

• To prevent fire or shock hazard, do not expose the unit to rain, moisture

• or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any openings or empty

slots in the unit, as you may damage parts inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any weight to be placed

upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or openings in the unit

housing that provide ventilation and allow for sufficient space for air to circulate

around the unit.

• Please completely disconnect the power when the unit is not in use to avoid wasting

electricity.

CONTENTS

1. Introduction……………………………………………......…………………………………………………….............……………………….1

2. Applications……………………………………………………..………………………………………………..............…………………….…1

3. PackageContents……………………………………………………………………………………….............…………………………..2

4. SystemRequirements………………………………………………………………………………….............…………………………2

5. Features………………………………………………………………………………………………………….............…………………………..2

6. Operation Controls and Functions…………………………………………………………...............……………………….3

6.1 Front Panel………………………………..………………………………………………………………………………………….….3

6.2 RearPanel……………………………………..……………………………………………………………………………………….…3

6.3 RemoteControl………………………………...…………………………………………………………………………..………..4

6.4 IR Cable Pinouts………………………………..………………………………………………………………………………….…5

6.5 RS-232 Pinout and Defaults……………………………………………………………………………………………....5

6.6 WebGUIControl…………………………………………………………………………………………………...…………………6

6.6.1 Monitor & Control Tab…………………………………………………………………………………………...…………....8

6.6.2 System Tab…………….…………………………………………………………………………………………………..21

6.6.3 Settings Tab………….……………………………………………………………………………………………….….24

6.6.4 Transmitter Tab………..………………………………………………………………………………………………35

6.6.5 Receiver Tab……………….………………………………………………………………………………………….…39

6.6.6 Scaling Tab……….………………………………………………………………………………………………….……43

6.6.7 Video Wall Tab…………….…………………………………………………………………………………………..44

6.6.8 Multiview Tab…………………………………………………………………………………………………...………46

6.7 TelnetControl……………………………………………………………………………………..…………………………………48

6.8 RS-232 and Telnet Commands……………………………………………………….……………………………….49

7. ConnectionDiagram…………………………………………………........……………………………..………………………………60

8. Specifications…………………………………………………………………........…………………………..……………………………….61

8.1 TechnicalSpecifications……………………………………...………………………………..…………………………….61

8.2 Video Specifications………………………………………………………………………………..………………………....62

8.3 Cable Specifications……………………………………………………………………………………..…………………....64

9. Acronyms………………………………………………………………………………………………………………..........…………..………65

1. INTRODUCTION

The KanexPro SDVoE powered Modular Matrix system is the most versatile flexible

video distribution solution. The system is composed of transceiver devices that can be

configured as either video transmitters or receivers with a simple click of a mouse. The

whole system is controlled and configured by a single control module which makes

setup a snap. Add the system to a 10G network and enjoy UHD 4K Lossless video with

zero latency.

The KanexPro Modular Matrix Controller (EXT-PROCTRL) is a powerful and flexible tool

for controlling multiple SDVoE (Software Defined Video over Ethernet) based extender

transceivers within same network. Install this unit onto the same local network as the

extenders to easily define and configure channel routing selections using the WebGUI. It

is also possible to define and switch routes using customized groups or presets allowing

for easy control over multiple video zones. Without the use of this controller, each

individual Transmitter and Receiver pair could only be configured in a basic point-to-

point operational mode.

Additionally, this unit supports controlling and configuring the matrix, video wall, and

multiviewer modes of connected SDVoE units. The settings of all connected transmitter/

receiver units, including IP configuration, compatibility settings, and extender status are

clearly displayed within the WebGUI. A trigger input interface is also provided to allow the

easy addition of a remote control keypad, or other trigger-supporting products, which can

be installed within a podium or table in a conference room or classroom. This interface can

allow the user to activate stored macros with the simple press of a button. Standard control

is available via WebGUI (remote or local), RS-232, Telnet and IR Remote.

2. APPLICATIONS

• Video/TV wall display and control

• Security surveillance and control

• Commercial advertising, display and control

• Home Theaters with Smart Home Controls

• Retail sales and demonstration

3. PACKAGE CONTENTS

• 1x EXT-PROCTRL IP Master Controller (SDVoE)

• 1x 5V/2.5A DC Power Adapter

• 1x Terminal Block (3-pin)

• 3x Terminal Block (5-pin)

• 1x IR Extender Cable

• 1x Remote Control (CR-183)

• 1x Shockproof Feet (Set of 4)

• 1x Operation Manual

4. SYSTEM REQUIREMENTS

• An active network connection from a switch or router for control of compatible AV

over IP devices.

5. FEATURES

• Enables the management and configuration of multiple compatible SDVoE extenders

through a single WebGUI

• Provides control over the independent routing of video, audio and control signals

between all local compatible transmitters and receivers

• Control over matrix, video wall, and multiviewer modes using WebGUI macros

• WebGUI clearly displays the status of all connected Transmitters and Receivers,

including IP address, channel selection, etc.

• Can generate serial commands to directly control an external serial-controllable device

• Can be powered by Ethernet switches supporting the IEEE 802.3af 2003 PoE

standard (Optional)

• Trigger Control Keypad support for easy, single-button, macro activation (Optional)

• Standard control is available via WebGUI (remote or local), RS-232, Telnet, and IR Remote

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

1. POWER LED: This LED will illuminate to indicate the unit is on and receiving power.

2. IR Window: Accepts IR signals from the included IR remote for control of this unit only.

6.2 Rear Panel

1. IR EXT Port: Connect to the provided IR Extender to extend the IR control range

of the unit. Ensure that the remote being used is within direct line-of-sight of the IR

Extender.

2. CONTROL 5-pin Terminal Block: Connect to a serial controllable device for the

transmission of RS-232 signals.

3. RS-232 3-pin Terminal Block: Connect to a PC, laptop or other serial control device

with a 3-pin adapter cable to control the unit via RS-232.

4. TRIGGER IN 10-pin Terminal Block: Connect to the Trigger Control Keypad

POWER

1 2

(OPTIONAL) or any device with trigger switch functionality such as window security

alarms, motion detectors, door switches, etc. Each of the 8 trigger inputs will activate

the associated macro (1~8) when triggered.

Note: A minimum of 5V DC is required to activate each trigger.

5. HDMI OUT Port: Connect to a standard HDMI display to view the unit’s current status

information and access the WebGUI directly without a PC.

Note: HDMI output is locked to a resolution of 1080p@60Hz.

6. USB Port: Connect a USB mouse and keyboard to control the unit’s WebGUI

displayed on the HDMI output port. Firmware update via USB is also supported.

Note: Specialized USB control devices, such as a touch panel, should be connected before the unit

is powered on.

7. LAN 2 Port: Connect directly, or through a network switch, to your PC/ laptop to

control the unit via WebGUI/Telnet.

8. LAN 1(POE) Port: This port is used to connect to the SDVoE devices to be controlled.

Connect to the SDVoE units’ private network through their dedicated network switch,

to enable detection and control over those units.

Note: If the connected network switch supports the IEEE 802.3af 2003 PoE (Power over Ethernet)

standard, this unit can optionally be powered directly via this Ethernet port.

FACTORY RESET Pinhole: Press and hold for 3 seconds to reset the unit to its factory defaults,

including Ethernet settings.

Note: While the reset is in process, the LEDs on the front of the unit will ﬂash. Once the reset is complete, the

unit will return to normal operation. DC 5V Port: Plug the 5V DC power adapter into the unit and connect it

to an AC wall outlet for power. (Optional, not required if the unit is powered via PoE).

6.3 Remote Control

1. PRESET 1~8: Press any of the 8 buttons to activate the saved preset associated with

that number.

6.4 IR Cable Pinouts

6.5 RS-232 Pinout and Defaults

6.6 WebGUI Control

• Device Discovery

Please obtain the “Device Discovery” software from your authorized dealer and save it in

a directory where you can easily find it.

Connect the unit and your PC/Laptop to the same active network and execute the

“Device Discovery” software. Click on “Find Devices on Network” and a list of devices

connected to the local network will show up indicating their current IP address.

Note: This unit defaults to DHCP mode. The current IP address can be veriﬁed using the HDMI

output or RS-232 if the Device Discovery software is not available.

By clicking on one of the listed devices you will be presented with the network details of

that particular device.

1. IP Mode: If you choose, you can alter the static IP network settings for the device,

or switch the unit into DHCP mode to automatically obtain proper network settings

from a local DHCP server. To switch to DHCP mode, please select DHCP from the IP

mode drop-down, then click “Save” followed by “Reboot”.

2. WebGUI Hotkey: Once you are satisfied with the network settings, you may use

them to connect via Telnet or WebGUI. The network information window provides a

convenient link to launch the WebGUI directly.

• WebGUI Overview

After connecting to the WebGUI’s address in a web browser, the WebGUI will load and

display the System tab. Click “Login” to open the authentication window. Please enter

the appropriate user name and password then click “Enter” to log in. If a keyboard is not

available, such as when using a touch screen, an on-screen keyboard can be activated

by clicking on the keyboard icon ( ).

Note: The default user name and password is “admin”.

After logging in, on the left side of the browser you will see the following menu tabs

where all primary functions of the unit are controllable via the built in WebGUI. The

individual functions will be introduced in the following sections.

Clicking the “Logout” button within the “System” tab will log the currently connected

user out of the WebGUI and return to login page.

Note: When not logged in, only the “Monitor & Control” and “System” tabs are available.

6.6.1 Monitor & Control Tab

This tab provides easy to use drag-and-drop control over all basic routing functionality

of the transmitters and receivers that have been detected within the local network. In all

sections, except for the Video section, transmitters are represented by the source icon

( ) and receivers are represented by the display icon ( ). Each of this tab’s sections

control the routing of a different type of interface that can be found on most compatible

transmitters, receivers or transceivers. These interfaces are: Video routing, Video Wall

routing, Multiview selection, HDMI Audio routing, Analog Audio routing, USB routing,

IR routing, RS-232 routing, and Macro activation. This tab’s controls are available even

when a user is not logged in, providing basic control over routing without exposing

system critical configuration areas.

Note: Units that were previously a part of the system, but are not currently detected will still be

displayed, however they will have a disconnected icon ( ) and cannot be used for routing.

1. Video Routing: Provides drag-and-drop control over the video routing between all

detected transmitters and receivers. Each transmitter and receiver box will display a

small, low framerate, video thumbnail to indicate what video is currently active.

Note: Certain operational modes (multiview, video wall) and some transmitters and receivers do

not support the video thumbnail feature.

• Video Transmitter: This section provides drag-and-drop buttons for all transmitters

detected by the system as well as a multi-option button target to stop video streams

from being transmitter.

Note: The IP Master Controller has an automatic bandwidth reduction feature to prevent situations

where a source’s streams will exceed 10Gbps, but in the unlikely event a transmitter’s streams

still require more bandwidth than is available, the video output may become visually unstable. In

these situations, it is recommended to reduce the resolution, framerate, or bit depth of the original

source.

• Source to Single Receiver Routing: To route a source to a receiver, click and drag

the source’s button on the left to the preferred display on the right side, then release

the mouse button. If the routing was completed successfully, the newly routed

source’s name will appear below the display’s name within the button. Clicking on

any source button will change the color of itself, and all currently routed displays.

Note: Receivers may also be drag and dropped onto sources to activate a new route.

• Source to Multiple Receiver Routing: To route a source to multiple receivers at the

same time, click and drag the source’s button on the left to a pre-defined Video Group

or “All” button on the right side, then release the mouse button. If the routing was

completed successfully, the source’s name will appear within all appropriate buttons.

• All/Native/Multiview Stream Stop: In certain situations, it may become necessary

to stop one or all of the video streams coming from a source. To do this, first select

the type of stream to stop by clicking on the cycle selection icon ( ) at the bottom

of the window until the preferred option (All Stop, Native Stop, Multiview Stop) is

displayed. Next, click and drag the source down to the chosen “Stop” button. The

chosen stream type will be immediately terminated. To stop a stream type from

ALL video streams simultaneously, drag the “All” button down to the chosen “Stop”

button. “All Stop” stops all stream types from the selected source, “Native Stop”

stops only the full resolution primary video stream, “Multiview Stop” stops only the

secondary video stream used by multiviewer layouts.

• Video Receiver: This section provides drag-and-drop buttons for all receivers

detected by the system as well as a button target to stop one or all output streams

from being displayed.

• Stop Stream: To stop the video stream on a single display, drag the display down to

the “Stop” button at the bottom of the window, then release the mouse button. To

stop ALL video outputs, drag the “All” button down to the “Stop” button.

• Status Icons: Status icons will be displayed instead of a video thumbnail image under

the following conditions:

Inhaltsverzeichnis

Andere KanexPro Matrix-Umschalter Handbücher

KanexPro

KanexPro 4K HDBaseT MX-HDBASE4X4-4K Bedienungsanleitung

KanexPro

KanexPro HDMX42-18G Bedienungsanleitung

KanexPro

KanexPro HDMX88-18G Bedienungsanleitung

KanexPro

KanexPro HDMX88A-18G Bedienungsanleitung

KanexPro

KanexPro SW-HDMX44DS Bedienungsanleitung

KanexPro

KanexPro HDMX88-18G Bedienungsanleitung

KanexPro

KanexPro MX-HDBASE8X8-4K Bedienungsanleitung

KanexPro

KanexPro HDMX44-18G Bedienungsanleitung

KanexPro

KanexPro HDMX44A-18G Bedienungsanleitung

KanexPro

KanexPro SW-HD4X24K Bedienungsanleitung

KanexPro

KanexPro HDMX88-4K Bedienungsanleitung

KanexPro

KanexPro HDMX42A-18G Bedienungsanleitung

KanexPro

KanexPro 4K HDBaseT MX-HDBASE4X4-4K Bedienungsanleitung

KanexPro

KanexPro HDMMX1616-4K Bedienungsanleitung

KanexPro

KanexPro MX-HDBASE8X8-4K Bedienungsanleitung

KanexPro

KanexPro MX-HDBT8X818G Bedienungsanleitung

KanexPro

KanexPro SW-HDMX44CE Bedienungsanleitung

KanexPro

KanexPro SW-HD4X24K Bedienungsanleitung

KanexPro

KanexPro MX-HDBASE6X6-4K Bedienungsanleitung

KanexPro

KanexPro HDC-MXB42AC Bedienungsanleitung

KanexPro

KanexPro HDMX44-4K Bedienungsanleitung

KanexPro

KanexPro SW-SDI8X8 Bedienungsanleitung

KanexPro

KanexPro SW-HDSC42D4K Bedienungsanleitung

KanexPro

KanexPro HDMX44-18G Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte