KANSAI SPECIAL V Series Bedienungsanleitung

INSTRUCTION







Industrial

Sewing

Machines

Third edition : March 2001

No. 010012

V7100/D,DE,F,ML

W8100/D,DE,F,C

W8042

W8042-1

V7002-1S

W8103-1S

INTRODUCTION

INTRODUCTIONINTRODUCTION

INTRODUCTION

Thank you for your purchasing Kansai Special's V.W Series.

Read and study this instruction manual carefully before beginning any of the

procedures and save it for later use.

1. This instruction manual describes adjustments and maintenance procedures on this

machine.

2. Before starting the machine, check to make sure the pulley cover, safety cover, etc.

are secured.

3. Before adjusting, cleaning, threading the machine or replacing the needle, be sure

to turn off the power.

4. Never start the machine with no oil in the reservoir.

5. Refer to the parts list as well as this instruction manual before performing

preventive maintenance.

6. The contents described in this instruction manual are subject to change without

notice.

CONTENTS

CONTENTSCONTENTS

CONTENTS

1. NEEDLES & THREADING THE MACHINE

1-1 Needles ･･････････････････････････････････････････････････････ 1

1-2 Replacing the needle ･･････････････････････････････････････････ 1

1-3 Threading the machine ････････････････････････････････････････ 1

2. MACHINE SPEED

2-1 Machine speed & direction in which the machine pulley runs ･････ 3

2-2 Motor & belt ･･････････････････････････････････････････････････ 3

3. LUBRICATION

3-1 Oil ･･･････････････････････････････････････････････････････････ 4

3-2 Oiling ････････････････････････････････････････････････････････ 4

3-3 Replacing the oil and the filter element ･････････････････････････ 4

4. SEWING MACHINE INSTALLATION

4-1 Cutting the machine table ･････････････････････････････････････ 5

4-2 Installing the machine ･････････････････････････････････････････ 6

5. TIMING OF THE LOOPER TO THE NEEDLES

5-1 Angle and height for installing the looper ･･･････････････････････ 6

5-2 Looper left-to-right movement ･･････････････････････････････････ 7

5-3 Needle height ･････････････････････････････････････････････････ 7

5-4 Length of the looper connecting bar ･････････････････････････････ 7

5-5 Looper setting distance ････････････････････････････････････････ 8

5-6 Needle/looper front-to-back relationship ････････････････････････ 8

6. FRONT AND REAR NEEDLE GUARDS

6-1 Position of the needle guard (rear) ･･････････････････････････････ 9

6-2 Position of the needle guard (front) ･････････････････････････････ 9

7. ADJUSTING THE FEED DOGS & STITCH LENGTH

7-1 Feed dog height ･･････････････････････････････････････････････10

7-2 Stitch length ･････････････････････････････････････････････････10

7-3 Differential feed ratio ････････････････････････････････････････10

8. ADJUSTING THE SPREADER

8-1 Position of the spreader ･･･････････････････････････････････････11

8-2 Position of the spreader thread eyelet ･･････････････････････････11

9. ADJUSTING THE PRESSER FOOT

9-1 Presser foot pressure ･････････････････････････････････････････12

9-2 Position of the presser foot & foot lift ･･････････････････････････12

10. ADJUSTING THE STITCH FORMATION

10-1 Position of the needle thread eyelet ････････････････････････････13

10-2 Position of the thread support ･････････････････････････････････13

10-3 Position of the spreader thread eyelet ･･････････････････････････13

10-4 Position of the thread eyelet of the looper thread take-up ････････14

10-5 Position of the looper thread take-up ･･････････････････････････14

11. CLEANING THE MACHINE

･･･････････････････････････････14

< Note >

Before replacing the needle, be sure to turn off the machine.

A clutch motor continues running for a while after the machine is turned off.

Therefore keep on pressing the pedal until the machine stops.

【1】NEEDLES & THREADING THE MACHINE

-1 Needles

1 Needles1 Needles

1 Needles

UY128GAS of Schmetz or Organ

Select the proper needle for the fabric and thread.

< Needles and needle size >

Schmetz UY128GAS Nm65 Nm70 Nm75 Nm80 Nm90

Organ

UY128GAS # 09 # 10 # 11 # 12 # 14

< Right needle of model-1S series >

Schmetz TV7 Nm75

Organ TV7 # 11

-2 Replacing the needle

2 Replacing the needle2 Replacing the needle

2 Replacing the needle

When replace the needle, check the needle carefully to see

that the scarf is turned to the rear of the machine (see the illustration). Then install the

needle correctly.

-3 Threading the machine

3 Threading the machine3 Threading the machine

3 Threading the machine

Thread the machine correctly by referring to the illustration below.

Threading the machine incorrectly may cause skip stitching, thread breakage and/or

uneven stitch formation.

A，B，C ... Needle threads

D .............. Top cover thread

E .............. Looper thread

A，B，C ... Needle threads

D ...............Top cover thread

E，F，G ... Looper thread

A，B，C，D ... Needle threads

E ..................... Top cover thread

F，G ...............Looper thread

【2】MACHINE SPEED

-1 Machine speed & direction in which the machine pulley runs

1 Machine speed & direction in which the machine pulley runs1 Machine speed & direction in which the machine pulley runs

1 Machine speed & direction in which the machine pulley runs

Refer to the table below for maximum and standard

speeds of the Series. To extend machine life, run

the machine approximately 15~20% below the

maximum speed for the first 200 hours of operation

(approx. 1 month). Then run the machine at the

standard speed. The machine pulley turns

counterclockwise as seen from the end of the

machine pulley.

-2 Motor & belt

2 Motor & belt2 Motor & belt

2 Motor & belt

Motor : 3-phase, 2-pole, 400W clutch motor

Belt : M type V belt

Select the proper motor pulley according to the

machine speed (refer to the motor pulley outer

diameter on the table below). Adjust where to

position the motor by pressing the finger onto the

middle of the belt so that 1~2cm deflection can be

obtained (see the illustration on the right).

< Machine speed >

Type Maximum speed Standard speed

V7100 6000SPM 5500SPM

W8100 5500SPM 5000SPM

W8042-1 4500SPM 4000SPM

W8103-1S 3000SPM 2500SPM

< Motor pulley selection table >

Machine speed

(SPM)

Motor pulley

outer diameter

(mm) 50Hz 60Hz

60 2500 2950

70 2900 3450

80 3300 3900

90 3700 4400

100 4100 4900

110 4500 5400

120 5000 5900

130 5300 (6400)

140 5800 (6900)

【3】LUBRICATION

-1 Oil

1 Oil1 Oil

1 Oil

Use Kansai Special’s genuine oil.

(Part No. 28-611)

-2 Oiling

2 Oiling2 Oiling

2 Oiling

■

To fill the machine with oil

Remove rubber plug A from the oil hole.

Fill the machine with oil until the oil level is at the

top line (see H in the illustration) on oil gauge C.

After the first lubrication, add oil so that the oil

level will be between H and L.

■

To check for proper oil flow

After filling the machine with oil, run the machine

to check the oil is splashing from oil pipe outlet B.

-3 Replacing the oil

3 Replacing the oil3 Replacing the oil

3 Replacing the oil and the filter element

and the filter elementand the filter element

and the filter element

To extend machine life, be sure to replace the oil

after the first 250 hours of operation.

To replace the oil, follow the procedures below.

1. Remove the V belt from the motor pulley and

then remove the machine from the table.

2. Remove screw D and then drain the oil.

Be careful not to stain V belt with the oil.

3. After draining the oil, be sure to tighten screw

4. Fill the machine with oil by referring to 3-2

shown above.

If filter element E is contaminated, proper oiling may not be performed.

Clean the filter element every six months. If just a little or no oil flows out from the

nozzle with the proper amount of oil in the machine, check the filter element.

To clean the filter element, remove oil reservoir.

【4】SEWING MACHINE INSTALLATION

-1 Cutting the machine table

1 Cutting the machine table1 Cutting the machine table

1 Cutting the machine table

-2 Installing the machine

2 Installing the machine2 Installing the machine

2 Installing the machine

Install the brackets on the underside of the table board (see the illustration below).

Fit the rubber cushions onto the brackets.

Mount the machine head on the rubber cushions.

【5】TIMING OF THE LOOPER TO THE NEEDLES

-1 Angle and height for installing the looper

1 Angle and height for installing the looper1 Angle and height for installing the looper

1 Angle and height for installing the looper

To obtain the proper angle and height, insert the

looper fully into looper holder A and then tighten

screw B.

The proper angle for the looper on V7100 and W8100

is 3°. Distance at 25mm from the point of the looper

between the bottom of the looper blade and the

extension line from the point of the looper :

Approximately 1.3mm

-2 Looper left

2 Looper left2 Looper left

2 Looper left-

-to

toto

to-

-right movement

right movementright movement

right movement

When the point of the looper, moving to the left or

right, has reached the left side of the left needle,

distances As from the top of the left needle's eye to the

point of the looper should be the same.(see the

illustration on the right). To adjust the timing of the

looper to the needles, remove the machine cover, loosen

three screws C on eccentric B and then shift the

eccentric by turning the machine pulley while holding

the eccentric.

-3 Needle height

3 Needle height3 Needle height

3 Needle height

When the needle bar is at the top of its stroke, adjust

distance A from the top surface of the needle plate to

the point of the left needle according to the gauge size

in the table below. To make this adjustment, loosen

nut B and move the needle bar up or down.

On W8042 and W8042-1, use the front needle for

reference.

Gauge size A (mm)

1/8

5/32 8.8

3/16 8.2

7/32 7.8

2-Needle

1/4 7.4

7/32 7.8

3-Needle 1/4 7.4

W8042 8.7

W8042-1 9.5

V7002-1S 9

W8103-1S 7.8

-4 Length of the looper connecting bar

4 Length of the looper connecting bar4 Length of the looper connecting bar

4 Length of the looper connecting bar

Adjust distance A between two connecting rods

according to pitch A in the table below (see the

illustration on the right).

Adjustment is made by loosening nuts B and turning

connecting bar C as required.

Model Pitch A (mm)

V7100 100

W8100 100

W8042 102

W8042-1 105

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KANSAI SPECIAL Nähmaschine Handbücher

KANSAI SPECIAL

KANSAI SPECIAL MZ Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DFB Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL SX Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL LX-SP Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DWK-1803D Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DX Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DFB1412PS Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL BX Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL BLX2202PC Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL RX9701J Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL SX Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL WX8803/UTC Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DLR-1501SPF Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DPW-1300 Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DFB1404P Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL MC 30 Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL RX/UTC Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DVK1702B Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL JJ Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL SX Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL BK-20 Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DFB MR-S Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL NC Series Bedienungsanleitung

KANSAI SPECIAL

KANSAI SPECIAL DX9902-3U Bedienungsanleitung

Beliebte Nähmaschine Handbücher anderer Marken

Riccar

Riccar RL634DE Bedienungsanleitung

Singer

Singer 2517 Bedienungsanleitung

Pfaff

Pfaff 3307-1 SERIES Bedienungsanleitung

Janome

Janome Quilt Maker Pro 18 VERSA Bedienungsanleitung

Siruba

Siruba C007JP Bedienungsanleitung

Husqvarna Viking

Husqvarna Viking Designer SE Bedienungsanleitung

Singer

Singer 148-5 Bedienungsanleitung

IKEA

IKEA SY Bedienungsanleitung

Pfaff

Pfaff 571 Bedienungsanleitung

Singer

Singer 15-91 Bedienungsanleitung

Brother

Brother BB370 Bedienungsanleitung

Pegasus

Pegasus WT100 Series Bedienungsanleitung

Reliable

Reliable 7100DB Bedienungsanleitung

Pfaff

Pfaff 937 Bedienungsanleitung

Singer

Singer 6038 Bedienungsanleitung

Singer

Singer 413K Bedienungsanleitung

Pfaff

Pfaff 1471 E1 Bedienungsanleitung

Kenmore

Kenmore 16677 - Serger Sewing Machine Bedienungsanleitung