Kärcher BD 38/12 C Bp Bedienungsanleitung

BD 38/12 C Bp

59655280 03/17

English 3

Français 19

Español 36

– 1

To reduce the risk of fire, electric

shock, or injury:

–DO NOT LEAVE appliance unat-

tended when plugged in. Unplug

from outlet when not in use and be-

fore servicing.

–TO REDUCE THE RISK OF ELEC-

TRIC SHOCK-USE INDOORS

ONLY

–Do not allow to be used as a toy.

Close attention is necessary when

used near children.

–Use only as discribed in this manu-

al. Use only manufacturer’s recom-

mended attachments.

–Do not use with damaged cord or

plug. If appliance is not working as

it should, has been dropped, dam-

aged, left outdoors, or dropped into

water, return it to a service center.

–Do not pull or carry by cord, use

cord as a handle, close a door on

cord, or pull cord around sharp edg-

es or corners. Do not run the unit

over cord. Keep cord away from

heated surfaces.

–Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

–Do not handle plug or appliance

with wet hands.

–Do not put any object into openings.

Do not use with any opening

blocked; keep free of dust, lint, hair,

and anything that may reduce air

flow.

–Keep hair, loose clothing, fingers,

and all parts of body away from

openings and moving parts.

–Turn off all controls before unplug-

ging.

–Use extra care when cleaning on

stairs.

–Do not use to pick up flammable or

combustible liquids, such as gaso-

line, or use in areas where they may

be present.

–Connect to a properly grounded

outlet only. See Grounding Instruc-

tions.

This appliance must be grounded. If it

should malfunction or break down,

grounding provides a path of least re-

sistance for electric current to reduce

the risk of electric shock.

The plug must be inserted into an ap-

propriate outlet that is properly in-

stalled and grounded in accordance

with all local codes and ordinances.

Improper connection of the equipment-

grounding conductor can result in a

risk of electric shock.

Check with a qualified electrician or

service person if you are in doubt as to

whether the outlet is properly ground-

ed.

Do not modify the plug provided with

the appliance.

If it will not fit the outlet, have a proper

outlet installed by a qualified electri-

cian.

IMPORTANT SAFETY IN-

STRUCTIONS

READ ALL INSTRUCTIONS

BEFORE USING.

WARNING

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

WARNING

3EN

– 2

This appliance is for use on a nominal

120-volt circuit and has a grounding at-

tachment plug that looks like the plug

illustrated in sketchpicture A. Make

sure that the appliance is connected to

an outlet having the same configura-

tion as the plug. No adaptor should be

used with this appliance.

CONNECT TO A PROPERLY

GROUNDED OUTLET ONLY

1 Grounded outlet

2 Grounded outlet box

3 Grounded pin

Save operation is in the responsibility

of the operator.

The operator shall be familiar with the

operation and function of all controls

and instruments before undertaking to

operate the unit.

Before operating the unit, operators

shall have read and be familiar with the

operator’s manual for the particular

unit being operated and they shall also

abide by the safety rules and practices

in the following paragraphs.

Before operating any unit, the operator

shall be familiar with unusual operating

conditions which may require addition-

al safety precautions or special operat-

ing instructions.

Before starting to operate the unit be in

operating position.

Do not start or operate the unit, any of

its functions or attachments, from any

place other than from the designated

operators position.

Before leaving the operator’s position:

A bring the unit to a complete stop;

B if the unit must be on an incline,

block the wheels.

Maintain a safe distance from the edge

of ramps, platforms, and other similar

working surfaces.

Do not add to, or modify the unit.

Do not block access to fire aisles, stair-

ways or fire equipment.

Yield the right of way to pedestrians

and emergency vehicles such as am-

bulances and fire trucks.

Cross railroad tracks at an angle wher-

ever possible. Do not park closer than

6 ft (1800 mm) to the nearest rail of a

railroad track.

Keep a clear view of the path of travel

and observe for other traffic, person-

nel, and safe clearances.

Under all travel conditions, operate the

unit at a speed that will pernit it to be

brought to a stop in a safe manner.

Do not indulge in stunt driving or horse-

play.

Slow down for wet and slippery floors.

Before driving over a dockboard or

bridge plate, be sure that it is properly

secured. Drive carefully and slowly

across the dockboard or bridge plate,

and never exceed its rated capacity.

When negotiating turns, reduce speed

to a safe level consistent with the oper-

ating environment. Make the turns

smoothly.

OPERATING SAFETY RULES

AND PRACTICES

Operator Responsibility

General

Travelling

4 EN

– 3

If the unit is found to be in need of repair

or in any way unsafe, or contributes to an

unsafe condition, the matter shall be re-

ported immediately to the user’s desig-

nated authority, and the unit shall not be

operated until it has been restored to

safe operating condition.

If during operation the unit becomes

unsafe in any way, the matter shall be

reported immediately to the user’s des-

ignated authority, and the unit shall not

be operated until it has been restored

to safe operating condition.

Do not make repairs or adjustments

unless specifically authorized to do so.

Operation of the unit may be hazard-

ous if maintenance is neglected or re-

pairs, rebuilds, or adjustments are not

performed in accordance with the man-

ufacturer’s design criteria. Therefore,

maintenance facilities (on or off prem-

ises), trained personnel, and detailed

procedures shall be provided.

Maintenance and inspection of the unit

shall be performed in conformance

with the following practices:

A a schedules planned maintenance,

lubrication, and inspection system

shall be followed; consult the man-

ufacturer’s recommendations.

B only tranined and authorized per-

sonnel shall be permitted to main-

tain, repair, adjust, and inspect the

unit, and in accordance with manu-

facturer’s specifications.

Avoid fire hazards and have fire pro-

tection equipment present in the work

area. Do not use open pans of fuel or

flammable cleaning fluids for cleaning

parts.

Any unit not in safe operating condition

shall be removed from service.

Repairs shall not be made in Class I,

Class II, and Class III locations.

Fire Prevention: The unit shall be kept

in a clean condition and reasonably

free of lint, excess oil, and grease.

Noncombustible agents are preferred

for cleaning the unit. Flammable liquids

[those having flash points at or above

100°F (37,8°C)] are not allowed. Pre-

cautions regarding toxicity, ventilation,

and fire hazard shall be appropriate for

the agent or solvent used.

Nameplate Visibility: The unit type des-

ignations as shown on the nameplate

and the type markers shall not be cov-

ered over with paint so that their identi-

fication information is obscured.

The unit shall not be used in classified

areas.

Operator care of the unit

MAINTENANCE AND RE-

BUILD PRACTICES

FIRE SAFETY STANDARD

5EN

– 4

Please read and comply with

these original instructions

prior to the initial operation of your ap-

pliance and store them for later use or

subsequent owners.

Before using the appliance for the first

time, read and observe these operat-

ing instructions and the accompanying

brochure: Safety information for brush

cleaning units, 5.956-251.0.

몇WARNING

Do not use the appliance on inclines.

The appliance may only be operated when

the container and all lids are closed.

DANGER

Pointer to immediate danger, which

leads to severe injuries or death.

몇WARNING

Pointer to a possibly dangerous situa-

tion, which can lead to severe injuries

or death.

몇CAUTION

Pointer to a possibly dangerous situa-

tion, which can lead to minor injuries.

ATTENTION

Pointer to a possibly dangerous situa-

tion, which can lead to property dam-

age.

Lithium-ion batteries are installed in

the appliance. These are subject to

special criteria. The removal and the

installation as well as the examination

of defective batteries may only be per-

formed by the Kärcher aftersales ser-

vice or a specialist.

Information on storage and transport

can be obtained from your Kärcher af-

tersales service.

DANGER

–Alterations and modifications on the

appliance are prohibited.

–Do not open the battery, as there

is a risk of an electrical shock; also,

irritating or caustic vapors can es-

cape.

–Do not expose the battery to di-

rect sunlight, heat or fire, there is

a risk of explosion.

–Do not operate the charger in explo-

sive environment.

–

Do not use the charger if dirty or wet.

–Ensure sufficient ventilation during

the charging process.

–Do not work with open flames, gen-

erate sparks or smoke in the vicinity

of a battery or a battery charging

room. Danger of explosion.

몇WARNING

–Check the appliance and the power

cable for damage prior to every use.

Do not use damaged appliances

Contents

Safety instructions . . . . . . . EN . . .4

Function . . . . . . . . . . . . . . . EN . . .5

Proper use . . . . . . . . . . . . . EN . . .5

Environmental protection . . EN . . .5

Operating elements . . . . . . EN . . .6

Before Startup . . . . . . . . . . EN . . .7

Operation . . . . . . . . . . . . . . EN . . .7

Transport . . . . . . . . . . . . . . EN . . .9

Storage. . . . . . . . . . . . . . . . EN . . .9

Care and maintenance. . . . EN . .10

Disposal . . . . . . . . . . . . . . . EN . .12

Faults . . . . . . . . . . . . . . . . . EN . .13

Accessories . . . . . . . . . . . . EN . .14

Technical specifications . . . EN . .15

Warranty. . . . . . . . . . . . . . . EN . .16

Spare parts. . . . . . . . . . . . . EN . .16

Safety instructions

Hazard levels

Information on battery (accumu-

lator) and charger

6 EN

– 5

and have damaged parts repaired

by specialists only.

–Keep children away from batteries

and charger.

–Do not charge damaged batteries.

Have damaged batteries replaced

by the Kärcher aftersales service.

–Do not discard defective batteries in

the domestic waste, inform Kärcher

aftersales service.

–Avoid contact with liquids oozing

out of defective battery packs.

Rinse thoroughly if you accidentally

come in contact with the fluid. Also

consult a doctor if the fluid comes in

contact with your eyes.

몇CAUTION

–These operating instructions must

be observed unconditionally. Ob-

serve recommendations of the law-

maker for handling batteries.

–The mains voltage must corre-

spond with the voltage indicated on

the type plate of the appliance.

–Use the charger only to charge ap-

proved battery packs.

–The accumulator may only be oper-

ated with this appliance. It is dan-

gerous and prohibited to use it for

other purposes.

If the safety switch is released, the

brush drive shuts off.

The scrubbing vacuum cleaner is used

for the wet cleaning of level floors.

It can be easily adjusted to the clean-

ing task by setting the water quantity.

A working width of 380 mm and a ca-

pacity of 12 l in the fresh and wastewa-

ter tank each enable effective cleaning

with long action times.

The battery can be charged on a 230V

power outlet by means of the integrat-

ed charger.

Use this appliance only as directed in

these operating instructions.

–The appliance should only be used

for cleaning level floors that are not

affected by moisture.

–This appliance is intended for inside

use.

–The appliance is not suited for the

cleaning of frozen grounds (e.g. in

cold stores).

–The appliance may only be

equipped with original accessories

and spare parts.

The packaging material can be

recycled. Please do not place the

packaging into the ordinary re-

fuse for disposal, but arrange for

the proper recycling.

Old appliances contain valuable

materials that can be recycled.

Please arrange for the proper re-

cycling of old appliances. Please

dispose your old appliances using

appropriate collection systems.

Notes about the ingredients

(REACH)

You will find current information about

the ingredients at:

www.kaercher.com/REACH

Safety installations

Function

Proper use

Environmental protection

7EN

– 6

1 Fresh water tank cover

2 Fluff filter

3 Push handle

4 Star knob, height adjustment of the

push rod

5 Star knob, transport position of the

push rod

6 Unlocking device, cover waste wa-

ter tank

7 Cover dirt water reservoir

8 waste water tank

9 Carrying handle for waste water

tank

10 Vacuum bar lift pedal

11 Splash guard

12 Cleaning head

13 Vacuum bar

14 Fresh water level display

15 Coupling for draining the fresh wa-

ter

16 Step depression

17 Battery charging display

18 Cable hook, rotating

19 Safety button

–The operating elements for the

cleaning process are yellow.

–The controls for the maintenance

and service are light gray.

Operating elements

Colour coding

8 EN

– 7

1 Dosage cleaning solution

2 Switch for detergent solution

3 Control lamp to apply detergent so-

lution

4 Indicator lamp vacuuming

Green: Suction turbine in operation

Orange, flashing: Suction turbine

overloaded

5 Indicator lamp brush drive

Green: Brush is rotating

Orange, flashing: Brush overloaded

6 Battery status display

Green Battery charged

Orange: Battery almost empty

Red Appliance swithces off: Load

battery

7 Indicator lamp Eco mode

8 Switch Eco mode

9 Power switch

Note:

The device is equipped with a safety

mechanism to prevent total discharge,

i.e. when the permissible minimum ca-

pacity is reached, the machine will be

shut off.

The charging process takes approx. 3

hours.

The charger automatically switches off

the charging process.

If necessary, the appliance can be

used again before the battery has been

fully charged.

Insert the mains plug into the sock-

et.

1 Battery is charged (green)

2 Battery is being charged (yellow,

flashing)

3 Malfunction (red)

Release the star knob for the trans-

port position.

Adjust the push rod to the desired

height.

Tighten the star handle.

Install the disc brush (see "Mainte-

nance and Servicing")

ATTENTION

Risk of damage. Only use the recom-

mended detergents. With other deter-

gents, the operator bears the

increased risk regarding the operation-

al safety, risk of accident and reduced

service life of the appliance. Only use

detergents that are free of solvents, hy-

drochloric acid and hydrofluoric acid.

Follow the safety instructions for using

detergents.

Before Startup

Charging battery

Battery charging display

Operation

Filling in detergents

9EN

– 8

Note:

Do not use highly foaming detergents.

Observe the dosing notes.

Swivel up the carrying handle of the

waste water tank.

Lift out the waste water tank and put

it aside.

Remove the lid from the fresh water

reservoir.

Fill in fresh water (maximum 50 °C).

Add detergent. Follow dosing in-

structions for detergent.

Recommended detergents:

Detergents are available in specialised

stores.

Close the cover of the fresh water

reservoir.

Place the waste water tank on the

appliance.

Release the star knob for the height

adjustment of the push rod.

Adjust the push handle to the de-

sired height.

Tighten the star handle.

Adjust the dosing of the cleaning

solution in accordance with the soil-

ing and the type of the flooring ma-

terial.

Bring the Eco mode switch into the

desired position.

Normal operation: The appliance

works at the maximum brush speed

and the highest suction perfor-

mance.

Eco: The appliance works at re-

duced brush speed and suction

performance. This also reduces the

energy consumption. The possible

action time with one charging cycle

increases.

ATTENTION

Risk of damage to the floor covering.

Do not operate the appliance on the

spot.

Risk of damage. Lift the vacuum bar

before pulling the appliance backwards

over a longer distance.

Set the appliance switch to "I".

Switch on "Detergent" button.

Push the pedal of the suction bar

lifting device simultaneously down

and to the left and allow it to go up

in order to lower the suction bar.

Pull the safety switch towards the

push handle, the brush drive and

the application of the cleaning solu-

tion are switched on (if preset).

Move the appliance over the sur-

face to be cleaned.

Release the safety switch.

Drive the appliance forward for an-

other 1-2 m to draw off residual wa-

ter.

Push down the pedal of the vacuum

bar lifting device to raise the vacu-

um bar.

Set the appliance switch to "0".

Application Detergent

Regular cleaning

(even for floors sensi-

tive to alkalies)

RM 745

RM 746

Cleaning dirt from

grease

RM 69 ES ASF

RM 69 ASF

Basic cleaning (strip-

ping) of alkali-resistant

hard coatings

RM 752

Basic cleaning (strip-

ping) linoleum

RM 754

Base cleaner, acidic RM 751

Disinfection cleaning RM 732

Settings

Cleaning

Shutting Down the Appliance

10 EN

Andere Handbücher für BD 38/12 C Bp

Inhaltsverzeichnis

Sprachen:

Andere Kärcher Bodenreinigungsmaschine Handbücher

Kärcher

Kärcher KM 90/60 R Bp Bedienungsanleitung

Kärcher

Kärcher KM 170/600 R D Bedienungsanleitung

Kärcher

Kärcher BDS 33/190 C Bedienungsanleitung

Kärcher

Kärcher KM 70/30 C Bp Bedienungsanleitung

Kärcher

Kärcher B 80 W Bp Bedienungsanleitung

Kärcher

Kärcher KM 100 R D Bedienungsanleitung

Kärcher

Kärcher KM 130/300 R D Bedienungsanleitung

Kärcher

Kärcher B 150 R Bedienungsanleitung

Kärcher

Kärcher KM 100 BP Bedienungsanleitung

Kärcher

Kärcher T 100 Bedienungsanleitung

Kärcher

Kärcher BR 530 BAT Package Bedienungsanleitung

Kärcher

Kärcher LB2000I Bedienungsanleitung

Kärcher

Kärcher KM 70/30 C Bp Bedienungsanleitung

Kärcher

Kärcher KMR 1700 D Bedienungsanleitung

Kärcher

Kärcher BR 40/25 C Bp Pack Bedienungsanleitung

Kärcher

Kärcher BR 30/4 C Adv Bedienungsanleitung

Kärcher

Kärcher KMR 1550 B Bedienungsanleitung

Kärcher

Kärcher BRC 30/15 C *JP Bedienungsanleitung

Kärcher

Kärcher B 80 W Bedienungsanleitung

Kärcher

Kärcher KM 70 C Bedienungsanleitung

Kärcher

Kärcher KM 75/40 W G Bedienungsanleitung

Kärcher

Kärcher KM 120/150 R Bp Bedienungsanleitung

Kärcher

Kärcher BR 40/10 C Classic Bedienungsanleitung

Kärcher

Kärcher CV 38/2 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung