Kathrein BAS 60 Bedienungsanleitung

Conversion set for flat antenna BAS 60 / BAS 61

- Modification instructions -

Purpose

Scope of the supply

Important notice!

Safety instructions

The conversion set must only be used for the modi-

fication of the flat antennas BAS 60 and BAS 61. The

conversion set changes the flat antenna BAS 60 to a

BAS 62 and the flat antenna BAS 61 to a BAS 63

(see opposite illustration). After the modification, the

mobile antennas BAS 60/BAS 61 are stationary anten-

nas BAS 62/BAS 63.

These instructions for the conversion of your antenna assume that you have the

skill and knowledge required for a correct rnodification. lf you do not have the

needed qualities, ask a specialist to do the job for you.

The modification work on the roof of your caravan, mobile home or truck can

create problems for your safety and life. Kathrein does not assume any responsi-

bility for damages to people and goods.

Park the vehicle in a safe place where you are not exposed to dangers (e.g. from

motor cars passing by) in order to carry out the conversion work.

Switch off the ignition and pull the handbrake. Only step on the roof of the vehicle

after having secured the working place.

Ladders or other climbing aids must be in perfect condition. Wear non-slip shoes.

The conversion set is composed of the preassembled

antenna support and 4 washers (see illustration oppo-

site). The modification instructions and the 12-page

mounting instructions „Flat antennas for stationary use,

BAS 62 and BAS 63“ are in the scope of supply of the

conversion set.

The conversion set for BAS 60/BAS 61 enables you to convert your mobile flat

antenna to a stationary antenna. The use determination (purpose) of your

antenna will also change. After the rnodification has been effected, the antennas

are identical with the flat antennas BAS 62 or BAS 63. These are flat antennas for

stationary use. The instructions for the „Conversion set“ are complemented by the

12-page brochure „Mounting instructions“ supplied together with the flat antennas

BAS 62/BAS 63.

The rnounting instructions contain important information regarding the stationary

use, the installation, the mounting site and the safety of your flat antenna. lt is

absolutely necessary that you pay attention to these instructions.

Do not separate the modification instructions from the mounting instructions. In

case you sell the antenna, both instructions should be handed over to the new

owner.

Antenna support

4 x washer

Mobile antenna

support

9985-551/798/1.3e

Conversion

• Loosen the two milled screws of the LNB cover.

Remove the cover and place it within reach.

• Loosen the two hex. socket head screws of the

mast bracket by means of an Allen key.

• Push the antenna cable somewhat backwards in

order to be long enough for the removal of the flat

antenna.

• Do not pull the cable through the mast into the

interior of the vehicle. lt is impossible to pull the

cable out again.

• Use both hands to remove the antenna from the

joint of the mast. Place the antenna with its back

pointing upwards on a solid non-slip support.

The LNB of the flat antenna BAS 61 has two outputs.

The LNB of the flat antenna BAS 60 has only one

antenna output.

The mobile antenna support of the flat antenna is

fastened on the back of the antenna with 4 hex.

socket head screws.

• Unscrew the 4 hex. socket head screws from

the mobile antenna support. Keep the screws in

a safe place because they will be needed again

for fastening the new antenna support.

• Now place the mobile antenna support on the joint

of the mast and tighten the mast bracket with the

aid of an Allen key.

• Unscrew the cable from the LNB and pull it out of

the cable support on the LNB.

• Then screw the LNB cover again to the flat

antenna. This will protect the LNB during the

transport of the flat antenna.

1. Unscrewing the cable from the LNB

2. Removal of the flat antenna

3. Removal of the mobile antenna support

Milled screws

Flat antenna

LNB-cover

Antenna cable

with plug

Joint

Support

Mobile antenna support

Mast

Bracket with

2 hex. socket

head screws

Lift up the

flat antenna

Lift up the

flat antenna

hex. socket

head screws

Antenna cable

9985-551/798/2.3e

hex. socket

head screws

lf you wish to drive with your vehicle without the flat

antenna mounted, but the jointed mast still installed,

you should protect the antenna as shown in opposite

illustration.

• Care for adequate insulation or sealing of the

antenna plug. Protect the plug from moisture.

• Bend the antenna cable to the form of a loop and

introduce the end of the cable into the joint of the

mast until the plug has disappeared in the lower

part of the joint.

Then check if the mobile antenna support is well

fixed. lf necessary, tighten the two socket head

screws of the bracket.

• Place the flat antenna evenly on an appropriate

support.

• Place the washers on the socket head screws and

screw the antenna support to the back of the flat

antenna (see opposite illustration). Use for that

purpose the 4 socket head screws belonging to

the mobile antenna support.

• Now screw in with your fingers the 4 socket head

screws. Pay attention that they are not twisted and

damage the thread.

• When positioning the antenna support, make sure

that the socket head screws are positioned exactly

in the middle of the elongated holes. Then take the

short shaft of an Allen key in your hand and screw

the socket head screws tight. See opposite

illustration.

• Then tighten the socket head screws with a torque

spanner. The torque moment is 6.5 Nm. lf no

torque spanner is available, the following method

will do: Take the long shaft of the Allen key in your

hand and tighten the socket head screws giving an

1/4 to an 1/2 turn.

6. Notice regarding the polarisation setting

The polarisation setting is dependent on the geo-

graphic reception site. The annexed mounting

instructions „Flat antennas BAS 62 and BAS 63

for stationary use“ explain on page 4 how the

polarisation is set.

4. Driving without the mounted flat antenna

5. Mounting the antenna support

Mobile antenna support

Joint

Driving direction

Cable binder

Cable plug

Take the long shaft of the

Allen key in your hand

and tighten the socket

head screws giving an

1/4 to an 1/2 turn.

Take the short

shaft of the Allen

key in your hand

and screw the

hex. socket

screw tight.

The hex. socket head screw

must be positioned in the

middle of the elongated

hole of the antenna support

Flat antenna

4 hex. socket head screws

with washers

9985-551/798/3.3e/H&S Subject to technical changes!

Antenna support

KATHREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 • Postfach 10 04 44 • D-83004 Rosenheim • Deutschland • Telefon (0 80 31) 18 40 • Fax (0 80 31) 18 43 06

Andere Handbücher für BAS 60

Dieses Handbuch passt für folgende Modelle

Andere Kathrein Antenne Handbücher

Kathrein

Kathrein CAS 80ro Bedienungsanleitung

Kathrein

Kathrein UAS584 Bedienungsanleitung

Kathrein

Kathrein CAS 09 Bedienungsanleitung

Kathrein

Kathrein BAS 60 Gebrauchsanweisung

Kathrein

Kathrein K 70 55 64 Bedienungsanleitung

Kathrein

Kathrein 506 10004 Bedienungsanleitung

Kathrein

Kathrein BZD 40 Bedienungsanleitung

Kathrein

Kathrein UHF-ANTENNEN OLYMPIA AOI 65 Bedienungsanleitung

Kathrein

Kathrein BZD 32 Bedienungsanleitung

Kathrein

Kathrein CAS 90ws/HD Bedienungsanleitung

Kathrein

Kathrein 214125 Bedienungsanleitung

Kathrein

Kathrein HDS 166 Bedienungsanleitung

Kathrein

Kathrein BAS 65 Bedienungsanleitung

Kathrein

Kathrein CAS 06 Bedienungsanleitung

Kathrein

Kathrein CAS 120 Bedienungsanleitung

Kathrein

Kathrein UFS 946/CI+ Betriebsanleitung

Kathrein

Kathrein AVH 06 Bedienungsanleitung

Kathrein

Kathrein K 51 24 72 Bedienungsanleitung

Kathrein

Kathrein UHF-ANTENNEN OLYMPIA AOI 65 Bedienungsanleitung

Kathrein

Kathrein LoRa Bedienungsanleitung

Kathrein

Kathrein 742215V01 Bedienungsanleitung

Kathrein

Kathrein BAS 60 Bedienungsanleitung

Kathrein

Kathrein ALC Bedienungsanleitung

Kathrein

Kathrein CAS 80gr Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung