Kauber InCeiling Bedienungsanleitung

a u b

-1-

CEILING PROJECTION SCREEN

INSTALLATION GUIDE

INCEILING

a u b

-2-

a u b

-3-

IMPORTANT!!!

INSTALLATION AND OPERATION NOTES

One of the wooden side blocks protecting the contents of the cardboard is at the same time

a mounting holes template - do not throw it out before the installation is finished.

The cassette and the bottom bar of the screen are protected against damage by polyurethane foam.

Remove the foams protecting the bottom bar after mounting the screen.

The screen should be installed in a location away from moisture and strong sunlight.

A properly mounted screen must be absolutely levelled.

Use a soft, moistened cloth for cleaning. Do not use active cleaners. Protect the screen from ingress of

water or other liquid inside. After cleaning, the screen should be carefully wiped to remove any residual

moisture.

DIMENSIONAL TOLERANCE: Projection surface: ± 20mm; components ± 3mm

7. The screen / elevator cannot have connected more than one remote control at once.

8. One remote control (for ex. RC01 / RC02 / Trigger 12V / Trigger230V / IR Receiver / RS Receiver,

etc.) cannot be connected at once to more than one screen, elevator, roller-blind, etc. Such connection

can only be made by using the SG-2 group controller.

KAUBER InCeiling is a top-class electric projection screen, designed for installation in a suspended

ceiling. Its smartly designed aluminum housing has many installation aids. In the Tensioned version it is

additionally equipped with a special system to get an even more tense projection surface. The InCeiling

series was created for suspend ceilings in both conference rooms and home cinemas.

Switch

Screen / elevator

engine

Screen / elevator

engine

Screen / elevator

engine

Controls

a u b

•

PACKAGE CONTENTS

projection screen - 1 pcs

mounting holes template. - 1 pcs

threaded rod - 4 pcs

engine adjustment wrench - 1 pcs

side panel - 2 pcs

main hole template - 1 pcs

M8 nut - 12 pcs.

tubular wrench 13 - 1 pcs

fixing support - 2 pcs

holes marker - 1 pcs

expansion dowel ø10 - 6 pcs

protective gloves - 2 pairs

a u b

-5-

Carefully unpack the contents of the packaging, paying special attention to wooden sides that

protect the contents of the carton from damage. Remember that one of them functions also as a

template for mounting holes, so do not throw it out before the installation is finished!

Stick the foil template of the main hole in the place designated for mounting the screen, and then outline

it with a pencil (Fig.1). After removing the foil, carefully cut in the ceiling the hole along the outline

made on the basis of the template.

Fig.1

Put a wooden block protecting the contents of the cardboard at each of the two ends of the hole, so that

the arrow printed on it points to the outside of the hole (Fig.2, Fig.2a).

Fig.2

SCREEN INSTALLATION

TEMPLATE

a u b

-6-

Fig.2a

Hold the template, and then guide the marker through the holes in the template to mark the drilling of

holes mounting in the fixed ceiling, (Fig.3).

Fig.3

Using the ø10 drill, drill the holes for the mounting dowels in the marked places. The holes should be

drilled in the correct order, starting with the hole marked on the template with the number 1 (Fig.4).

After drilling the hole 1 correctly, move to drilling holes 2 and 3. Then, drill holes 4 and 5. Repeat for

the opposite side.

a u b

-7-

Fig.4

In place of the holes drilled in fixed ceiling, screw the mounting supports using the attached dowels and

screws (Fig.5).

NOTE! The mounting dowels supplied in the set can be used only for ceilings made of solid materials

(for ex. concrete, suporex). When attaching the screen to materials other than those listed, choose

appropriate mounting dowels.

Fig. 5

-8-

Threaded rods have to be cut to the appropriate length using the following formula:

After cutting, each of the threaded rods should be screwed into a suitable hole in the mounting support,

and then countered with an M8 nut (Fig.6).

Tighten each of the mounted rods with an M8 nut at a distance of approx. 5-6 cm from the bottom end

of the rod, then try on the screen cassette. If necessary, adjust the position of the nut so that the

mounting brackets of the screen cassette rest on the nuts and the bottom edge of the cassette rests

against the suspended ceiling.

Fig.7

w w w . k a u b e r . e u

Fig.6

rod length =

distance between the fixed ceiling

and the bottom edge of the suspended

ceiling

- 7 cm

a u

-9-

10.

After connecting the power supply (see page no.15) slide the screen onto the mounted rods and screw

each of the 4 M8 nuts using the included pipe wrench while checking the stability of the entire

installation (Fig.8). A properly installed screen must be levelled. Correct the fixing by unscrewing or

screwing the mounting nuts on the appropriate threaded rods.

A properly installed screen is shown below (Fig.9). All connections are countered. Such an installation

protects the screen against the occurrence of vibrations and possible resonances. The movement of the

nuts 1 and 2 allows to accurately level the screen, which is required for the proper operation of the

screen.

Fig.9

Fig.8

CEILING

counter

Nut 1

Nut 2

SCREEN

a u

-10-

11. The delivered screen has end positions set in accordance with the order. If the surface of the screen

scrolls too low or not enough, correct the bottom end position using the included wrench. Before

adjustment, check in the warranty card with what type of engine is your screen equipped with.

NOTE! Adjustments to the end positions can only be made by a qualified person. All adjustments are

made at your own risk. In the event of an inaccurate adjustment, the screen may get damaged, which is

not covered by the terms of the warranty.

Fig.10

12.

After final verification of the entire installation, place the side panels on magnets stuck to the panels

(Fig. 11). In screens with side tension, unfold the surface completely. If necessary, use the allen key to

adjust the tension with the bolts on both sides of the bottom bar.

Fig.11

White end stop

Yellow end stop

Access to the

end stop

Inhaltsverzeichnis

Andere Kauber Projektionsfläche Handbücher

Kauber

Kauber FRAME LITE Series Bedienungsanleitung

Kauber

Kauber Red Label Bedienungsanleitung

Kauber

Kauber FRAME Series Bedienungsanleitung

Kauber

Kauber INCEILING XL Bedienungsanleitung

Kauber

Kauber FRAME Series Bedienungsanleitung

Kauber

Kauber BLUE LABEL Bedienungsanleitung

Kauber

Kauber CLR Bedienungsanleitung

Kauber

Kauber Blue Label XL Bedienungsanleitung

Kauber

Kauber MIDI Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung