KEBCO COMBIBOX Bedienungsanleitung

INSTRUCTION MANUAL

KEB COMBIBOX

00.10.000-I01U

6/2022

TABLE OF CONTENTS

DETERMINING UNIT TYPE..................................................................... 2

INSTALLATION & WIRING....................................................................... 3

PERMISSIBLE SHAFT LOAD .................................................................. 4

OPERATION & MAINTENANCE .............................................................. 4

ADJUSTING INSTRUCTIONS ................................................................. 5

REPLACEMENT & REPAIR PROCEDURE ............................................. 6

ELECTRONIC CONTROLS & ACCESSORIES ....................................... 6

EXPLODED VIEW XX.10.670*................................................................. 7

EXPLODED VIEW OF XX.10.370*........................................................... 8

*XX denotes Size

For further information please contact KEB AMERICA, Inc. at 1-952-224-

1400.

DETERMINING UNIT TYPE

In order to properly mount and wire the KEB Combibox, it is necessary to

identify the type of the unit. To do this, nd the part number of the unit, which

is located on top of the terminal box. It should be in the following format:

XX.YY.ZZZ (Example: 06.10.370)

YY indicates Type as follows:

The clutch rotor transmits the power from the input to the output by making

secure frictional contact with the armature. The armature is fastened to the

output shaft. The arrow on the Combibox housing always points from the

input (clutch side) to the output (brake side). Mount the unit accordingly!

2Combibox Instruction Manual

INSTALLATION & WIRING

When direct DC voltage is supplied

to the Combibox, the terminal strip

shown in Figure 1 will be mounted

in the conduit box.

Polarity in the clutch and brake is

not relevant when wiring type 09,

10, and 16, but it is relevant when

wiring the type 06 Combibox. The

green wire with the red stripe is

positive and the green wire with the

blue stripe is negative.

When AC power is supplied to the Combibox, a rectier will be used in place

of the terminal strip. See Figures 2 and 3 for possible wiring congurations

for a type 09 or 10 Combibox. See Figure 4 for the wiring conguration for

a type 06 or 16 Combibox.

Figure 2 Figure 3

There are two basic rectiers avail-

able for clutch/brake combination:

• 02.91.020-CE07 for 110VAC/

95VDC, bridge rectier

• 02.91.010-CE07 for 220VAC/

95VDC, half wave rectier.

Figure 4

Relays for switching should be

rated at least 250VDC/10A



















   











 







 

PERMISSIBLE SHAFT LOAD

The value FNrefers to the load at the middle of the shaft, distance L/2. It

is based on a sercive, life of 10,000 h and a speed of 1500 rpm. For other

speed and service life values, FN can be calculated with the aid of the graph

shown above. If additional axial forces occur, a recalculation of the bearing

load should be performed by the factory.

Example:

Lh= 5000 h, n = 1000rpm

F/FN= 1.5 therefore F = 1.5 x FN

OPERATION & MAINTENANCE

The KEB Combibox is shipped ready for installation with the air gap

preadjusted to the nominal value. NEMA, or IEC mounting dimensions on

the input and output ends allow for easy assembly to motors and gearboxes.

DO NOT FORCE FIT when mounting. An antiseize lubricant should be used

on the shaft when mounting the Combibox. To avoid contamination of the

friction surfaces, do not use excessive amounts of lubricant.

Proper sizing of the Combibox in accordance with the application will

minimize wear and reduce maintenance. The air gap should be readjusted

according to the instructions when it reaches three times its nominal

4Combibox Instruction Manual

PLEASE NOTE: REFER TO PAGE 2, “DETERMINING UNIT TYPE,”

BEFORE PROCEEDING.

• TYPES 09 AND 16 MUST BE RETURNED TO KEB AMERICA FOR

ADJUSTMENT.

1. For type 10, engage the brake by supplying the proper DC voltage to

the brake magnet. For type 06, no power is required.

2. Remove the access plugs from each side of the Combibox.

3. Loosen the two lock nuts (See Figure 5).

4. Insert the feeler gauge between the clutch magnet and the armature.

Tighten the adjusting screws(clockwise) until the nominal air gap is

reached. The air gap should be equal on each side (See Figure 6).

5. Tighten the lock nuts.

6. Screw the plugs back into the access holes.

Figure 5 Figure 6

ADJUSTING INSTRUCTIONS

When the Combibox has reached maximum wear, the wear parts must

be replaced. Wear parts include the brake magnet, the armature, and the

clutch rotor. To order spare parts, provide the 11 digit part number, or the

following information:

1. Size and type of unit

2. Magnet voltage

3. Input style of unit (solid or hollow shaft, and bore size)

In order to replace worn parts with new parts, refer to the next page and

proceed as follows:

1. Open the terminal box and loosen all electrical connections to the clutch

and the brake.

2. Disassemble the Combibox housing by unscrewing the four bolts.

3. Replace the worn clutch rotor with the new rotor Avoid any contamination

of the friction lining. The clutch rotor is always on the input side of

the Combibox, the arrow on the housing points from the input to the

output.

4. Replace the armature and the brake magnet with the new parts. Use

LOCTITE when tightening all screws. Clean friction surfaces with

pure alcohol before installation.

5. Wire the clutch and the brake terminals in the conduit box.

6. Assemble the Combibox and adjust the air gap as outlined above.

REPLACEMENT & REPAIR PROCEDURE

ELECTRONIC CONTROLS & ACCESSORIES

KEB Combitron 33.94 Rapid Switch

The combitron 33.94 provides a smooth 24VDC signal to the clutch/brake

unit through activation by proximity switches, photocells, mechanical relays,

etc. The 33.94 briey overexcites the coils, which reduces switching times

for a given load by approximately 2/3’s. Extremely high cycle rates can be

achieved while maintaining the absolute accuracy necessary for complex

motion control applications.

Rectiers

KEB rectiers are the best in the industry and are varistor protected for

maximum safety when switching inductive loads. Bridge and half-wave

rectiers are available for AC or DC side switching.

6Combibox Instruction Manual

EXPLODED VIEW XX.10.670

KEB AMERICA, Inc.

5100 Valley Industrial Blvd S

Shakopee, MN 55379

Phone: 1-952-224-1400 • Fax: 1-952-224-1499

www.kebamerica.com

[email protected]

EXPLODED VIEW OF XX.10.370

Inhaltsverzeichnis

Andere KEBCO Steuereinheit Handbücher

KEBCO

KEBCO COMBIVERT H6 Series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F6 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT G6 Betriebsanleitung

KEBCO

KEBCO COMBIVERT F4-S Series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT CONTROL G6 VARAN Betriebsanleitung

KEBCO

KEBCO COMBIVERT H6 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F4-S/1.2 Gebrauchsanweisung

KEBCO

KEBCO C6-COMPACT II Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5-A Gebrauchsanweisung

KEBCO

KEBCO COMBIVERT H6 Series Bedienungsanleitung

KEBCO

KEBCO F5 COMBICOM ModBus Bedienungsanleitung

KEBCO

KEBCO COMBIVERT G6 Betriebsanleitung

KEBCO

KEBCO COMBIVERT G6 series Betriebsanleitung

KEBCO

KEBCO COMBIVERT G6 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT 00F6V80-001A Bedienungsanleitung

KEBCO

KEBCO 00.F4.010-3009 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT H6 Series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT H6 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung