Kenwood Nexedge NX-230EX Bedienungsanleitung

B62-2449-30 (E)

NX-230EX/ NX-330EX

VHF DIGITAL TRANSCEIVER/ UHF DIGITAL TRANSCEIVER

INstructIoN MaNual

ÉMETTEUR-RÉCEPTEUR NUMÉRIQUE VHF/ ÉMETTEUR-RÉCEPTEUR NUMÉRIQUE UHF

MoDE D’EMPloI

TRANSCEPTOR DIGITAL VHF/ TRANSCEPTOR DIGITAL UHF

MaNual DE INstruccIoNEs

RICETRASMETTITORE DIGITALE VHF/ RICETRASMETTITORE DIGITALE UHF

MaNualE DI IstruzIoNI

VHF DIGITAL FUNKGERÄT/ UHF DIGITAL FUNKGERÄT

BEDIENuNgsaNlEItuNg

VHF DIGITALE ZENDONTVANGER/ UHF DIGITALE ZENDONTVANGER

gEBruIksaaNwIjzINg

VHF SAYISAL EL TELSİZİ/ UHF SAYISAL EL TELSİZİ

kullaNIM kIlaVuzu

ΨΗΦΙΑΚΟΣ ΠΟΜΠΟΔΕΚΤΗΣ VHF/ ΨΗΦΙΑΚΟΣ ΠΟΜΠΟΔΕΚΤΗΣ UHF

ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ

VHF DIGITAL TRANSCEIVER/

UHF DIGITAL TRANSCEIVER

NX-230EX/ NX-330EX

INSTRUCTION MANUAL

ENGLISH

NOTIFICATION

This equipment complies with the essential

requirements of Directive 2014/53/EU.

Restrictions

This equipment requires a licence and is intended for

use in the countries as below.

AT BE DK FI FR DE GR IS IE

IT LI LU NL NO PT ES SE CH

GB CY CZ EE HU LV LT MT PL

SK SI BG RO HR TR ISO3166

The AMBE+2TM voice coding Technology embodied in this product

is protected by intellectual property rights including patent rights,

copyrights and trade secrets of Digital Voice Systems, Inc. This

voice coding Technology is licensed solely for use within this

Communications Equipment. The user of this Technology is explicitly

prohibited from attempting to extract, remove, decompile, reverse

engineer, or disassemble the Object Code, or in any other way

convert the Object Code into a human-readable form. U.S. Patent

Nos. #8,315,860, #8,595,002, #6,912,495, #8,200,497, #7,970,606,

and #8,359,197.

Firmware Copyrights

The title to and ownership of copyrights for firmware embedded in

KENWOOD product memories are reserved for JVCKENWOOD

Corporation.

THANK YOU

We are grateful you have chosen KENWOOD for your land

mobile radio applications.

NOTICES TO THE USER

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegal operation is punishable by ﬁne and/or imprisonment.

◆Refer service to qualiﬁed technicians only.

Safety:

◆ It is important that the operator is aware of, and understands,

hazards common to the operation of any transceiver.

◆ For use in explosive atmospheres, read additional document

“SAFETY MANUAL FOR HAZARDOUS LOCATIONS” (B62-

2450-XX).

Information on Disposal of Old Electrical and Electronic Equipment and Batteries

(applicable for countries that have adopted separate waste collection systems)

Products and batteries with the symbol (crossed-out wheeled bin) cannot

be disposed as household waste.

Old electrical and electronic equipment and batteries should be recycled

at a facility capable of handling these items and their waste byproducts.

Contact your local authority for details in locating a recycle facility nearest

to you.

Proper recycling and waste disposal will help conserve resources whilst

preventing detrimental effects on our health and the environment.

Notice: The sign "Pb" below the symbol for batteries indicates that this

battery contains lead.

PRECAUTIONS

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the

transceiver and the battery pack.

• Use only KENWOOD speciﬁed explosion-protected options for the

NX-230EX and NX-330EX transceivers.

• If the die-cast chassis or other transceiver part is damaged, do not

touch the damaged parts.

• Do not place the microphone cable around your neck while near

machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the

radiator and chassis will become hot. Do not touch these locations

when replacing the battery pack.

• Do not immerse the transceiver in water.

• Always switch the transceiver power oﬀbefore installing optional

accessories.

• The charger is the device that disconnects the unit from the AC

mains line.The AC plug should be readily accessible.

iii

Turn the transceiver power oﬀin the following locations:

• Near blasting sites.

• In aircrafts.(Any use of the transceiver must follow the instructions

and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of

radio devices, including but not limited to medical facilities.

• Near persons using pacemakers.

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while the

vehicle is running. When the airbag inﬂates, the transceiver may be

ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if any

metallic parts are exposed from the antenna covering. Transmitting

at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the

transceiver, switch the transceiver power oﬀimmediately, remove

the battery pack from the transceiver, and contact your KENWOOD

dealer.

• Use of the transceiver while you are driving may be against traﬃc

laws. Please check and observe the vehicle regulations in your

area.

• Do not expose the transceiver to extremely hot or cold conditions.

• Do not carry the battery pack with metal objects, as they may short

the battery terminals.

• Danger of explosion if the battery is incorrectly replaced; replace

only with the same type.

Information concerning the battery pack:

The battery pack includes ﬂammable objects such as organic

solvent. Mishandling may cause the battery to rupture producing

ﬂames or extreme heat, deteriorate, or cause other forms of

damage to the battery. Please observe the following prohibitive

matters.

• Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suﬀer serious damage, the battery may

generate heat or smoke, rupture, or burst into ﬂame.

• Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such

as a paper clip or wire). Do not carry or store the battery pack in

containers holding metal objects (such as wires, chain-necklace or

hairpins). If the battery pack is short-circuited, excessive current will

ﬂow and the battery may generate heat or smoke, rupture, or burst

into ﬂame. It will also cause metal objects to heat up.

• Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function is

damaged, or the electrolyte is ignited, the battery may generate

heat or smoke, rupture, or burst into ﬂame.

• Do not leave the battery near ﬁre, stoves, or other heat

generators (areas reaching over 80°C)!

If the polymer separator is melted due to high temperature, an

internal short-circuit may occur in the individual cells and the battery

may generate heat or smoke, rupture, or burst into ﬂame.

• Avoid immersing the battery in water or getting it wet by

other means!

If the battery becomes wet, wipe it oﬀwith a dry towel before use. If

the battery’s protection circuit is damaged, the battery may charge

at extreme current (or voltage) and an abnormal chemical reaction

may occur. The battery may generate heat or smoke, rupture, or

burst into ﬂame.

• Do not charge the battery near ﬁre or under direct sunlight!

If the battery’s protection circuit is damaged, the battery may charge

at extreme current (or voltage) and an abnormal chemical reaction

may occur. The battery may generate heat or smoke, rupture, or

burst into ﬂame.

• Use only the speciﬁed charger and observe charging

requirements!

If the battery is charged in unspeciﬁed conditions (under high

temperature over the regulated value, excessive high voltage or

current over regulated value, or with a remodeled charger), it may

overcharge or an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into ﬂame.

• Do not pierce the battery with any object, strike it with an

instrument, or step on it!

This may break or deform the battery, causing a short-circuit. The

battery may generate heat or smoke, rupture, or burst into ﬂame.

• Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat or smoke,

rupture, and/or burst into ﬂame. If the battery’s protection circuit

is damaged, the battery may charge at an abnormal current (or

voltage), and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into ﬂame.

• Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

ﬂame.

• Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety function

is damaged, the battery may generate heat or smoke, rupture, or

burst into ﬂame.

• Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical reaction

may occur. In some cases, an unexpected large amount of current

may ﬂow upon discharging. The battery may generate heat or

smoke, rupture, or burst into ﬂame.

• Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating

equipment, do not force it; check the polarity of the battery. If the

battery pack is reverse-connected to the charger, it will be reverse-

charged and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into ﬂame.

• Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes, wash

your eyes with fresh water as soon as possible, without rubbing

your eyes. Go to the hospital immediately. If left untreated, it may

cause eye-problems.

• Do not charge the battery for longer than the speciﬁed time!

If the battery pack has not ﬁnished charging even after the

regulated time has passed, stop it. The battery may generate heat

or smoke, rupture, or burst into ﬂame.

• Do not place the battery pack into a microwave or high

pressure container!

The battery may generate heat or smoke, rupture, or burst into

ﬂame.

• Keep ruptured and leaking battery packs away from ﬁre!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from ﬂammable areas. Electrolyte leaking

from battery can easily catch on ﬁre and may cause the battery to

generate smoke or burst into ﬂame.

• Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have diﬀerent

coloring, is deformed, or seems abnormal for any other reason,

remove it from the charger or operating equipment and do not use

it. The battery may generate heat or smoke, rupture, or burst into

ﬂame.

Andere Handbücher für Nexedge NX-230EX

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kenwood Transceiver Handbücher

Kenwood

Kenwood TS-830 Bedienungsanleitung

Kenwood

Kenwood TK-880 series Bedienungsanleitung

Kenwood

Kenwood TK-2212L Bedienungsanleitung

Kenwood

Kenwood TH-78A Bedienungsanleitung

Kenwood

Kenwood TS-130S Bedienungsanleitung

Kenwood

Kenwood TS-930S Bedienungsanleitung

Kenwood

Kenwood TK-260G Bedienungsanleitung

Kenwood

Kenwood TH-26A Bedienungsanleitung

Kenwood

Kenwood Nexedge Bedienungsanleitung

Kenwood

Kenwood TH-K7 Bedienungsanleitung

Kenwood

Kenwood TH-22A Bedienungsanleitung

Kenwood

Kenwood TK-785 Bedienungsanleitung

Kenwood

Kenwood TS-700 Bedienungsanleitung

Kenwood

Kenwood TM-631A Bedienungsanleitung

Kenwood

Kenwood Pro Talk VHF Bedienungsanleitung

Kenwood

Kenwood TK-3000 K Bedienungsanleitung

Kenwood

Kenwood TR-7200G Bedienungsanleitung

Kenwood

Kenwood TH-78A Bedienungsanleitung

Kenwood

Kenwood TS-50S Bedienungsanleitung

Kenwood

Kenwood TK-5210 Bedienungsanleitung

Kenwood

Kenwood TS-700 Bedienungsanleitung

Kenwood

Kenwood UHF P25 Transceiver TK-5810 Bedienungsanleitung

Kenwood

Kenwood TS-820 Bedienungsanleitung

Kenwood

Kenwood NX-3220 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung

Standard Horizon

Standard Horizon HX320E Bedienungsanleitung

Em-Trak

Em-Trak A100 Bedienungsanleitung

HPE

HPE Aruba QSFP28 Bedienungsanleitung

RADTEL

RADTEL RT-490 Bedienungsanleitung