Kenwood TK-2140 Bedienungsanleitung

09 08 07 06 05 04 03

INSTRUCTION MANUAL

VHF FM TRANSCEIVER

TK-2140

TK-3140

UHF FM TRANSCEIVER

WARNING:

EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.)

Tu rn off your transceiver while taking on fuel, or while parked in

gasoline service stations.

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegal operation is punishable by fine and/or imprisonment

◆Refer service to qualified technicians only.

SAFETY: It is important that the operator is aware of

and understands hazards common to the operation of

any transceiver.

THANK YOU

We are grateful you chose KENWOOD for your land

mobile radio applications. We believe this easy-to-use

transceiver will provide dependable communications to

keep personnel operating at peak efficiency.

KENWOOD transceivers incorporate the latest in

advanced technology. As a result, we feel strongly that

you will be pleased with the quality and features of this

product.

MODELS COVERED BY THIS MANUAL

•TK-2140: VHF FM Transceiver

•TK-3140: UHF FM Transceiver

NOTICES TO THE USER

One or more of the following statements may be

applicable:

ATTENTION (U.S.A. Only):

The RBRC Recycle seal found on KENWOOD

nickel-cadmium (Ni-Cd) battery packs indicates

KENWOOD’s voluntary participation in an industry

program to collect and recycle Ni-Cd batteries after

their operating life has expired. The RBRC program

is an alternative to disposing Ni-Cd batteries with

your regular refuse or in municipal waste streams,

which is illegal in some areas.

For information on Ni-Cd battery recycling in your area, call (toll free)

1-800-8-BATTERY (1-800-822-8837).

KENWOOD’s involvement in this program is part of our commitment

to preserve our environment and conserve our natural resources.

FCC WARNING

This equipment generates or uses radio frequency energy. Changes

or modifications to this equipment may cause harmful interference

unless the modifications are expressly approved in the instruction

manual. The user could lose the authority to operate this equipment

if an unauthorized change or modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY

THE FCC

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from that

to which the receiver is connected.

•Consult the dealer for technical assistance.

iii

CONTENTS

UNPACKING AND CHECKING EQUIPMENT ................... 1

SUPPLIED ACCESSORIES ......................................... 1

PREPARATION .................................................. 2

BATTERY PACK PRECAUTIONS .................................... 2

INSTALLING/ REMOVING THE (OPTIONAL) RECHARGEABLE BATTERY

PACK OR ALKALINE BATTERY CASE ............................... 7

INSTALLING/ REMOVING ALKALINE BATTERIES ...................... 8

INSTALLING THE (OPTIONAL) ANTENNA ............................ 9

INSTALLING THE BELT CLIP ....................................... 9

INSTALLING THE COVER OVER THE UNIVERSAL CONNECTOR .........10

INSTALLING THE (OPTIONAL KMC-25) SPEAKER/ MICROPHONE ...10

GETTING ACQUAINTED .......................................11

DISPLAY ......................................................13

PROGRAMMABLE AUXILIARY FUNCTIONS ................14

OPERATION OVERVIEW .......................................16

TRUNKING FORMAT ............................................16

CONVENTIONAL FORMAT ........................................16

OPERATING BASICS ...........................................17

SWITCHING POWER ON/ OFF ..................................17

ADJUSTING THE VOLUME .......................................17

SELECTING ASYSTEM/ GROUP/ CHANNEL ........................17

TIME-OUT TIMER (TOT) .......................................18

TRUNKED OPERATION (Trunking Format) ..................19

PLACING ADISPATCH CALL .....................................19

RECEIVING ADISPATCH CALL ...................................19

CONVENTIONAL OPERATION (Trunking Format) ...........20

TRANSMITTING .................................................20

RECEIVING ....................................................20

SYSTEM SCAN (Trunking Format) ...........................21

SCANNING TRUNKED SYSTEMS ..................................21

SCANNING CONVENTIONAL SYSTEMS .............................21

SCAN LOCKOUT ................................................22

SCAN REVERT .................................................22

GROUP SCAN (Trunking Format) ............................23

CONVENTIONAL OPERATION (Conventional Format) .....24

TRANSMITTING .................................................24

RECEIVING ....................................................24

SCAN (Conventional Format) ................................25

PRIORITY SCAN ................................................25

2-TONE SIGNALLING (Conventional Format) ..............26

FleetSync™: ALPHANUMERIC 2-WAY PAGING FUNCTION ... 27

KEY FUNCTIONS ...............................................27

SELCALL (SELECTIVE CALLING) .................................28

STATUS MESSAGE .............................................30

OPTIONAL SHORT MESSAGES FEATURE ..........................32

AUDIBLE USER FEEDBACK TONES ..........................33

UNPACKING AND CHECKING EQUIPMENT

Note: The following unpacking instructions are for use by your

KENWOOD dealer, an authorized KENWOOD service facility, or the

factory.

Carefully unpack the transceiver. We recommend that

you identify the items listed in the following table before

discarding the packing material. If any items are missing

or have been damaged during shipment, file a claim with

the carrier immediately.

SUPPLIED ACCESSORIES

metI rebmuNtraP ytitnauQ

pilctleBXX-1070-92J1

pacrotcennoclarevinUXX-5260-90B1

wercsdesserDXX-8450-80N1

dracytnarraW—1

launamnoitcurtsnIXX-6741-26B1

Belt clip Universal

connector cap

Dressed

screw

BATTERY PACK PRECAUTIONS

◆Do not recharge the battery pack if it is already fully charged.

Doing so may cause the life of the battery pack to shorten or the

battery pack may be damaged.

◆After recharging the battery pack, disconnect it from the charger.

If the charger power is reset (turned ON after being turned OFF),

recharging will start again and the battery pack will become

overcharged.

◆Do not use the transceiver while charging the battery pack. We

recommend you switch the transceiver power OFF while charging

is taking place.

◆Do not short the battery terminals or dispose of the battery by

fire.

◆Never attempt to remove the casing from the battery pack.

Information concerning the (optional) Li-ion battery pack:

The battery pack includes flammable objects such as organic solvent.

Mishandling may cause the battery to rupture producing flames or

extreme heat, deteriorate, or cause other forms of damage to the

battery. Please observe the following prohibitive matters.

•Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suffer serious damage, the battery may

generate heat or smoke, rupture, or burst into flame.

•Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such as

a paperclip or wire). Do not carry or store the battery pack in

containers holding metal objects (such as wires, chain-neckless or

hairpins). If the battery pack is short-circuited, excessive current

will flow and the battery may generate heat or smoke, rupture, or

burst into flame. It will also cause metal objects to heat up.

PREPARATION

DANGER

•Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function is

damaged, or the electrolyte is ignited, the battery may generate

heat or smoke, rupture, or burst into flame.

•Do not use or leave the battery near fires, stoves, or other

heat generators (areas reaching over 80°C/ 176°F)!

If the polymer separator is melted due to high temperature, an

internal short-circuit may occur in the individual cells and the

battery may generate heat or smoke, rupture, or burst into flame.

•Do not immerse the battery in water or get it wet by other

means!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

•Do not charge the battery near fires or under direct sunlight!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

•Use only the specified charger and observe charging

requirements!

If the battery is charged in unspecified conditions (under high

temperature over the regulated value, excessive high voltage or

current over regulated value, or with a remodelled charger), it

may overcharge or an abnormal chemical reaction may occur.

The battery may generate heat or smoke, rupture, or burst into

flame.

•Do not pierce the battery with any object, strike it with an

instrument, or step on it!

This may break or deform the battery, causing a short-circuited.

The battery may generate heat or smoke, rupture, or burst into

flame.

•Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat or smoke,

rupture, and/or burst into flame. If the battery’s protection circuit is

damaged, the battery may charge at an abnormal current (or

voltage), and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

•Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

flame.

•Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety function

is damaged, the battery may generate heat or smoke, rupture, or

burst into flame.

•Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical

reaction may occur. In some cases, an unexpected large amount

of current may flow upon discharging. The battery may generate

heat or smoke, rupture, or burst into flame.

•Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating

equipment, do not force it; check the polarity of the battery. If the

battery pack is reverse-connected to the charger, it will be

reverse-charged and an abnormal chemical reaction may occur.

The battery may generate heat or smoke, rupture, or burst into

flame.

•Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes, wash

your eyes out with fresh water as soon as possible, without

rubbing your eyes. Go to the hospital immediately. If left

untreated, it may cause eye-problems.

•Do not charge the battery for longer than the specified time!

If the battery pack has not finished charging even after the

regulated time has passed, stop it. The battery may generate

heat or smoke, rupture, or burst into flame.

•Do not place the battery pack into a microwave or high

pressure container!

The battery may generate heat or smoke, rupture, or burst into

flame.

•Keep ruptured and leaking battery packs away from fire!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from flammable areas. Electrolyte leaking

from battery can easily catch on fire and may cause the battery to

generate smoke or burst into flame.

•Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have different

coloring, is deformed, or seems abnormal for any other reason,

remove it from the charger or operating equipment and do not

use it. The battery may generate heat or smoke, rupture, or burst

into flame.

■Using the Li-ion Battery Pack

•Charge the battery pack before using it.

•To keep the battery discharge at a minimum, remove

the battery pack from the equipment when it is not in

use. Store the battery pack in a cool and dry location.

•When storing the battery pack for a long period:

1Remove the battery pack from the equipment.

2Discharge the battery pack, if possible.

3Store the battery pack in a cool (below 25°C/ 77°F)

and dry location.

Andere Handbücher für TK-2140

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kenwood Transceiver Handbücher

Kenwood

Kenwood NX-3200 Bedienungsanleitung

Kenwood

Kenwood Nexedge NX-230EX Bedienungsanleitung

Kenwood

Kenwood TM-221A Bedienungsanleitung

Kenwood

Kenwood TR-7625 Bedienungsanleitung

Kenwood

Kenwood ProTalk tk-3501 Bedienungsanleitung

Kenwood

Kenwood TS-450S Bedienungsanleitung

Kenwood

Kenwood TK-880 series Bedienungsanleitung

Kenwood

Kenwood TK 3230 - FreeTalk XLS UHF Montage- und Bedienungsanleitung

Kenwood

Kenwood TM-733A Bedienungsanleitung

Kenwood

Kenwood TS-670 Bedienungsanleitung

Kenwood

Kenwood TK-8100 Bedienungsanleitung

Kenwood

Kenwood NX-1700N-C Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Kenwood

Kenwood TS-870S Bedienungsanleitung

Kenwood

Kenwood ProTalk NX-P500 Bedienungsanleitung

Kenwood

Kenwood TH-D72A Bedienungsanleitung

Kenwood

Kenwood TK-760G series Bedienungsanleitung

Kenwood

Kenwood TS-930S Bedienungsanleitung

Kenwood

Kenwood TK-285 Bedienungsanleitung

Kenwood

Kenwood TH-G71A Bedienungsanleitung

Kenwood

Kenwood TM-V7A/E Bedienungsanleitung

Kenwood

Kenwood TK-780 series Bedienungsanleitung

Kenwood

Kenwood TK-2140 Bedienungsanleitung

Kenwood

Kenwood TS-120S Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung

Standard Horizon

Standard Horizon HX320E Bedienungsanleitung

Em-Trak

Em-Trak A100 Bedienungsanleitung

HPE

HPE Aruba QSFP28 Bedienungsanleitung