Kenwood TK2360ISK Bedienungsanleitung

09 08 07 06 05 04 03 02 01 00

INSTRUCTION MANUAL

VHF FM TRANSCEIVER

TK-2360

UHF FM TRANSCEIVER

TK-3360

Thank You

We are grateful you have chosen Kenwood for your land

mobile radio applications.

noTices To The user

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegaloperationispunishablebyneand/orimprisonment.

◆ Referservicetoqualiedtechniciansonly.

SAFETY: It is important that the operator is aware of and

understands hazards common to the operation of any

transceiver.

Firmware Copyrights

Thetitletoandownershipofcopyrightsforrmwareembeddedin

Kenwood product memories are reserved for Kenwood Corporation.

One or more of the following statements may be applicable:

FCC WARNING

This equipment generates or uses radio frequency energy.

Changes or modications to this equipment may cause harmful

interference unless the modications are expressly approved in the

instruction manual. The user could lose the authority to operate this

equipment if an unauthorized change or modication is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY

THE FCC

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can generate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that the

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer for technical assistance.

The RBRC Recycle seal found on Kenwood

lithium-ion (Li-ion) battery packs indicates

Kenwood’s voluntary participation in an industry

program to collect and recycle Li-ion batteries

after their operating life has expired. The RBRC

program is an alternative to disposing Li-ion

batteries with your regular refuse or in municipal

waste streams, which is illegal in some areas.

For information on Li-ion battery recycling in your area, call (toll

free) 1-800-8-BATTERY (1-800-822-8837).

Kenwood’s involvement in this program is part of our commitment

to preserve our environment and conserve our natural resources.

The RBRC Recycle seal found on

Kenwood

nickel

metal hydride (Ni-MH) battery packs indicates

Kenwood’s

voluntary participation in an industry

program to collect and recycle Ni-MH batteries after

their operating life has expired. The RBRC program

is an alternative to disposing Ni-MH batteries with

your regular refuse or in municipal waste streams,

which is illegal in some areas.

For information on Ni-MH battery recycling in your area, call (toll

free) 1-800-8-BATTERY (1-800-822-8837).

Kenwood’s involvement in this program is part of our commitment

to preserve our environment and conserve our natural resources.

Precautions

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the

transceiver and the battery pack.

• Do not use options not specied by Kenwood.

• If the die-cast chassis or other transceiver part is damaged, do not

touch the damaged parts.

• If a headset or headphone is connected to the transceiver, reduce

the transceiver volume. Pay attention to the volume level when

turning the squelch off.

• Do not place the microphone cable around your neck while near

machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the

radiator and chassis will become hot. Do not touch these locations

when replacing the battery pack.

• Always switch the transceiver power off before installing optional

accessories.

• The charger is the device that disconnects the unit from the AC

mains line. The AC plug should be readily accessible.

iii

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while

the vehicle is running. When the airbag inates, the transceiver

may be ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if

any metallic parts are exposed from the antenna covering.

Transmitting at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the

transceiver, switch the transceiver power off immediately,

remove the battery pack from the transceiver, and contact your

Kenwood dealer.

• Use of the transceiver while you are driving may be against

trafc laws. Please check and observe the vehicle regulations

in your area.

• Do not expose the transceiver to extremely hot or cold

conditions.

• Do not carry the battery pack (or battery case) with metal

objects, as they may short the battery terminals.

• Danger of explosion if the battery is incorrectly replaced;

replace only with the same type.

Turn the transceiver power off in the following locations:

• Near blasting sites.

• In airplanes. (Any use of the transceiver must follow the

instructions and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of

radio devices, including but not limited to medical facilities.

• Near persons using pacemakers.

information concerning the battery Pack

The battery pack includes ammable objects such as organic solvent.

Mishandling may cause the battery to rupture producing ames or

extreme heat, deteriorate, or cause other forms of damage to the

battery. Please observe the following prohibitive matters.

•Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suffer serious damage, the battery may

generate heat or smoke, rupture, or burst into ame.

•Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such

as a paper clip or wire). Do not carry or store the battery pack

in containers holding metal objects (such as wires, chain-

necklace or hairpins). If the battery pack is short-circuited,

excessive current will ow and the battery may generate heat

or smoke, rupture, or burst into ame. It will also cause metal

objects to heat up.

•Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function

is damaged, or the electrolyte is ignited, the battery may

generate heat or smoke, rupture, or burst into ame.

•Do not use or leave the battery near fires, stoves, or other

heat generators (areas reaching over 80°C/ 176°F)!

If the polymer separator is melted due to high temperature,

an internal short-circuit may occur in the individual cells and

the battery may generate heat or smoke, rupture, or burst into

ame.

•Avoid immersing the battery in water or getting it wet by

other means!

If the battery becomes wet, wipe it off with a dry towel before

use. If the battery’s protection circuit is damaged, the battery

may charge at extreme current (or voltage) and an abnormal

chemical reaction may occur. The battery may generate heat or

smoke, rupture, or burst into ame.

• Do not charge the battery near fires or under direct

sunlight!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal

chemical reaction may occur. The battery may generate heat or

smoke, rupture, or burst into ame.

•Use only the specified charger and observe charging

requirements!

If the battery is charged in unspecied conditions (under high

temperature over the regulated value, excessive high voltage

or current over regulated value, or with a remodelled charger),

it may overcharge or an abnormal chemical reaction may occur.

The battery may generate heat or smoke, rupture, or burst into

ame.

•Do not pierce the battery with any object, strike it with an

instrument, or step on it!

This may break or deform the battery, causing a short-circuit.

The battery may generate heat or smoke, rupture, or burst into

ame.

•Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat

or smoke, rupture, and/or burst into ame. If the battery’s

protection circuit is damaged, the battery may charge at an

abnormal current (or voltage), and an abnormal chemical

reaction may occur.

• Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

ame.

•Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety

function is damaged, the battery may generate heat or smoke,

rupture, or burst into ame.

•Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical

reaction may occur. In some cases, an unexpected large

amount of current may ow upon discharging. The battery may

generate heat or smoke, rupture, or burst into ame.

• Do not charge the battery for longer than the specified

time!

If the battery pack has not nished charging even after the

regulated time has passed, stop it. The battery may generate

heat or smoke, rupture, or burst into ame.

•Do not place the battery pack into a microwave or high

pressure container!

The battery may generate heat or smoke, rupture, or burst into

ame.

•Keep ruptured and leaking battery packs away from fire!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from ammable areas. Electrolyte

leaking from battery can easily catch on re and may cause the

battery to generate smoke or burst into ame.

•Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have different

coloring, is deformed, or seems abnormal for any other reason,

remove it from the charger or operating equipment and do not

use it. The battery may generate heat or smoke, rupture, or

burst into ame.

•Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating

equipment, do not force it; check the polarity of the battery. If

the battery pack is reverse-connected to the charger, it will be

reverse-charged and an abnormal chemical reaction may occur.

The battery may generate heat or smoke, rupture, or burst into

ame.

•Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes,

wash your eyes out with fresh water as soon as possible,

without rubbing your eyes. Go to the hospital immediately. If

left untreated, it may cause eye-problems.



UNPACKING AND CHECKING EQUIPMENT. . . . . . . . . . . . . . . . . . . 1

PREPARATION..........................................2

ORIENTATION ..........................................7

PROGRAMMABLE AUXILIARY FUNCTIONS . . . . . . . . . . . . . . . . . . 8

BASICOPERATIONS....................................11

SCAN ...............................................12

FleetSync: ALPHANUMERIC 2-WAY PAGING SYSTEM . . . . . . . . . 14

VOICE OPERATED TRANSMISSION (VOX) . . . . . . . . . . . . . . . . . . 15

BACKGROUNDOPERATIONS ............................16



Note: These unpacking instructions are for use by your Kenwood

dealer, an authorized Kenwood service facility, or the factory.

Carefully unpack the transceiver. If any items are missing or

damaged, le a claim with the carrier immediately.



Beltclip................................................1

Speaker/ microphone jacks cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Speaker/ microphone locking bracket . . . . . . . . . . . . . . . . . . . . . . . . . 1

Stopper (4-channel: white) . ................................1

Stopper(8-channel: gray)..................................1

Stopper(12-channel: black)................................1

Instructionmanual........................................1

1Match the guides of the

battery pack with the grooves

on the upper rear of the

transceiver, then rmly press

the battery pack in place.

2Lock the safety catch to

prevent accidentally releasing

the battery pack.

3To remove the battery pack,

lift the safety catch, press the

release latch, then pull the

battery pack away from the

transceiver.

Note:

◆For battery pack charging procedures and useage, refer to the

battery charger Instruction Manual.

◆Before charging a battery pack that is attached to the

transceiver, ensure that the safety catch is rmly closed.



◆ Do not install batteries in a hazardous environment where

sparks could cause an explosion.

◆ Never discard batteries in re; extremely high temperatures can

cause batteries to explode.

◆Do not short circuit the battery case terminals.

◆Do not use rechargeable batteries.





Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kenwood Transceiver Handbücher

Kenwood

Kenwood TK-3148 Bedienungsanleitung

Kenwood

Kenwood TS-700A Bedienungsanleitung

Kenwood

Kenwood TM-621A Bedienungsanleitung

Kenwood

Kenwood UBZ-LH68 Bedienungsanleitung

Kenwood

Kenwood TK-3173K4 Bedienungsanleitung

Kenwood

Kenwood TK-5210 Bedienungsanleitung

Kenwood

Kenwood FreeTalk XL Bedienungsanleitung

Kenwood

Kenwood TK-2260EX Bedienungsanleitung

Kenwood

Kenwood TK-7302E Bedienungsanleitung

Kenwood

Kenwood TK-90 Bedienungsanleitung

Kenwood

Kenwood TK-D200G Bedienungsanleitung

Kenwood

Kenwood TK 3230 - FreeTalk XLS UHF Bedienungsanleitung

Kenwood

Kenwood TR-7625 Bedienungsanleitung

Kenwood

Kenwood TH-28A Bedienungsanleitung

Kenwood

Kenwood TH-225A Bedienungsanleitung

Kenwood

Kenwood TS-2000 Bedienungsanleitung

Kenwood

Kenwood TK-5710 Series Bedienungsanleitung

Kenwood

Kenwood TS-700SP Bedienungsanleitung

Kenwood

Kenwood TK-360G Bedienungsanleitung

Kenwood

Kenwood TS-430S Bedienungsanleitung

Kenwood

Kenwood TS-780 Bedienungsanleitung

Kenwood

Kenwood UBZ-LF14 Bedienungsanleitung

Kenwood

Kenwood TM-411A Bedienungsanleitung

Kenwood

Kenwood TS-440S Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung

Standard Horizon

Standard Horizon HX320E Bedienungsanleitung

Em-Trak

Em-Trak A100 Bedienungsanleitung

HPE

HPE Aruba QSFP28 Bedienungsanleitung