Keysight Technologies E8257D Installations- und Betriebshandbuch

NOTE: For the latest revision of this installation note,

go to the following website:

http://www.keysight.com/find/psg

Keysight E8257D/67D

PSG Signal Generators

Add Option 1EH (Improved Low Band Harmonics from

10 MHz to 3.2 GHz)

Kit Part Number: E8251-60382

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

E8251-90382

Edition

Edition 1, August 2015

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note E8251-90382 3

Add Option 1EH (Improved Low Band Harmonics from 10 MHz to 3.2 GHz) Kit Part Number:

E8251-60382

Add Option 1EH (Improved Low Band Harmonics from

10 MHz to 3.2 GHz)

Kit Part Number: E8251-60382

Introduction

This upgrade kit adds Option 1EH (Improved Low Band Harmonics) to the E8257D (Analog) and

E8267D (Vector) PSG Signal Generators.

Installation includes the following major steps, starting on page 5:

1. Check signal generator functionality.

2. Remove the outer and inner signal generator covers.

3. Install Option 1EH.

4. Activate Option 1EH.

5. Verify proper installation of Option 1EH.

6. Re-assemble the signal generator.

7. Verify signal generator calibration.

Product Affected: . . . . . . . . . . . . . . . . . . . . . . . . . E8257D/67D

Serial Numbers: . . . . . . . . . . . . . . . . . . . . . . . . . . E8257D Prefix < US/MY/SG4928

E8267D Prefix < US/MY/SG5042

Options: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

To Be Performed By: . . . . . . . . . . . . . . . . . . . . . . (X) Keysight Technologies Service Center

(X) Personnel Qualified by Keysight Technologies

(X) Customer

Estimated Installation Time: . . . . . . . . . . . . . . . 1.0 hour

Estimated Verification Time: . . . . . . . . . . . . . . . 1.0 hour

4Installation Note E8251-90382

Add Option 1EH (Improved Low Band Harmonics from 10 MHz to 3.2 GHz) Kit Part Number:

E8251-60382

Installation Kit Parts List

Tools Required

— TORX T-10 driver

— TORX T-15 driver

— TORX T-20 driver

— 5/16” open-ended wrench

— Needle-nose pliers

Item Quantity Description Part Number

1 1 Installation Note E8251-90382

2 1 A38 Low Band Switch Filter E8251-60305

3 1 W76 Semi-Rigid Cable E8251-20590

4 1 W118 Semi-Rigid Cable E8251-20588

5 1 W119 Semi-Rigid Cable E8251-20589

6 4 Cable Retainer Base E8251-40001

7 4 Cable Retainer Top E8251-40007

8 1 Entitlement Certificate 5964-5143

9 1 Entitlement Certificate Envelope 5967-7169

Installation Note E8251-90382 5

Add Option 1EH (Improved Low Band Harmonics from 10 MHz to 3.2 GHz) Kit Part Number:

E8251-60382

Safety Considerations

Check Signal Generator Functionality

Use the following procedure to confirm that the signal generator powers up and the internal check

identifies no errors. The internal check evaluates the operation of the signal generator and returns

an error message if it detects a problem.

1. Turn on the signal generator and let it warm up for at least five minutes.

2. Run the signal generator self-test by pressing Utility > Instrument Info/Help Mode > Self

Test > Run Complete Self Test. Upon completion, a summary of the self-test will be

displayed. Use the E8257D/67D PSG Service Guide to troubleshoot any failures detected by

the test.

3. Check to see if the ERR annunciator is on.

—If the ERR annunciator is on, review the error messages in the error queue by pressing

Utility > Error Info. The first page of error messages in the error queue appears in the

display text area. (Refer to the signal generator error messages document for information

about each error message.)

After resolving all problems causing errors, press Clear Error Queue(s).

—If the ERR annunciator is off, the signal generator functionality check has passed.

Before you disassemble the signal generator, turn the power switch

off and unplug the power cord. Failure to unplug the signal

generator can result in personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All

work on electronic assemblies should be performed at a static-safe workstation.

When the signal generator is first connected to ac line power, the error message

ERROR 514, Reference Oven Cold occurs which causes both the OVEN COLD

annunciator and the ERR annunciator to turn on.

After approximately five minutes, the OVEN COLD annunciator automatically

clears, but the ERR annunciator remains on until all errors are cleared from the

error queue.

Some circuits may require up to 50 minutes to warm up before passing the

self-test. If self-tests continue to fail after 50 minutes of warm up, troubleshoot

the instrument.

6Installation Note E8251-90382

Add Option 1EH (Improved Low Band Harmonics from 10 MHz to 3.2 GHz) Kit Part Number:

E8251-60382

Remove the Outer and Inner Signal Generator Covers

Remove the Outer Cover

Refer to Figure 1.

1. Disconnect the power cord.

2. Using a T-20 driver, loosen the two screws (1) and remove the strap handle (2).

3. Using a T-15 driver, remove the center screws (3) on the four rear-panel feet (4).

4. Remove the four bottom feet (5) from the cover by lifting the tab and sliding the foot toward

the tab.

5. Place the signal generator on its side.

6. Tilt the signal generator forward and slide the outer cover (6) back to remove it from the frame.

Remove the Inner Top Cover

Refer to Figure 2.

1. Using a T-10 driver, remove the screws (1) from the inner-top cover (2). There are twelve

screws for E8257D and eleven screws for E8267D.

2. Remove the inner-top cover.

Installation Note E8251-90382 7

Add Option 1EH (Improved Low Band Harmonics from 10 MHz to 3.2 GHz) Kit Part Number:

E8251-60382

Figure 1 Outer Cover Removal

8Installation Note E8251-90382

Add Option 1EH (Improved Low Band Harmonics from 10 MHz to 3.2 GHz) Kit Part Number:

E8251-60382

Figure 2 Inner Top Cover Removal

Install Option 1EH (For Instruments without Option UNW)

Refer to Figure 3 for steps 1-3.

Refer to Figure 4 for steps 4-14.

Refer to for Figure 7 steps 15 and 16.

1. Remove A6 thru A8.

2. Using needle-nose pliers remove the cable retainer base for W37 (E8251-20225).

3. With the A31 Motherboard facing you, using the 5/16” open-ended wrench, remove the other

end of semi-rigid cable W37.

4. Position the instrument on it’s side.

5. Place a cable retainer base on W118 (E8251-20588).

6. Insert W118 through the A31 Motherboard, at the A38 Lowband Switch Filter (IN) opening.

7. Using the needle-nose pliers, connect a cable retainer top to W118.

Installation Note E8251-90382 9

Add Option 1EH (Improved Low Band Harmonics from 10 MHz to 3.2 GHz) Kit Part Number:

E8251-60382

8. Place a cable retainer base on the other end of W118.

9. Insert W118 through the A31 Motherboard, at the A8 LB Output (OUT) opening.

10.Using the needle-nose pliers, connect a cable retainer top to W118.

11.Place a cable retainer base on W119 (E8251-20589).

12.Insert W119 through the A31 Motherboard, at the A38 Lowband Switch Filter (OUT) opening.

13.Using the needle-nose pliers, connect a cable retainer top to W119.

14.Using the 5/16” open-ended wrench, connect the other end of W119 to the

A23 Lowband Coupler/Detector.

15.Position the instrument with the RF deck on top and the front panel facing you.

16.Install the A38 Lowband Switch Filter (Option 1EH) assembly.

10 Installation Note E8251-90382

Add Option 1EH (Improved Low Band Harmonics from 10 MHz to 3.2 GHz) Kit Part Number:

E8251-60382

Figure 3 Placement of W37

W37

Andere Handbücher für E8257D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Keysight Technologies Tragbarer Generator Handbücher

Keysight Technologies

Keysight Technologies B2961A Bedienungsanleitung

Keysight Technologies

Keysight Technologies E8251-60384 Kurzanleitung

Keysight Technologies

Keysight Technologies N5191A Kurzanleitung

Keysight Technologies

Keysight Technologies M8100A Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies UXG X Series Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies N5171B EXG Bedienungsanleitung

Keysight Technologies

Keysight Technologies X Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies 33210A Bedienungsanleitung

Keysight Technologies

Keysight Technologies M9383B VXG-m Bedienungsanleitung

Keysight Technologies

Keysight Technologies N5166B CXG Bedienungsanleitung

Keysight Technologies

Keysight Technologies B2961B Bedienungsanleitung

Keysight Technologies

Keysight Technologies UXG X-Series Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies X Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies X-Series Betriebsanleitung

Keysight Technologies

Keysight Technologies X Series Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies M8190A Bedienungsanleitung

Keysight Technologies

Keysight Technologies N9310A Bedienungsanleitung

Keysight Technologies

Keysight Technologies E8257D Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies N8241A Bedienungsanleitung

Keysight Technologies

Keysight Technologies M8196A Bedienungsanleitung

Keysight Technologies

Keysight Technologies X Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies E8267D Bedienungsanleitung

Keysight Technologies

Keysight Technologies 33210A Bedienungsanleitung

Keysight Technologies

Keysight Technologies B2961B Betriebsanleitung

Beliebte Tragbarer Generator Handbücher anderer Marken

Kohler

Kohler 20EORZ Bedienungsanleitung

Powerhorse

Powerhorse 83171 Bedienungsanleitung

HURST

HURST ML-630-SI Bedienungsanleitung

ETQ

ETQ TG4000 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton 40265 Einrichtungshandbuch

ConMed

ConMed 7550 Bedienungsanleitung

Owon

Owon Waveform Generator Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

Power Stroke

Power Stroke PS906025 Bedienungsanleitung

Firefly

Firefly Cygnus CYG2400/460/24 Bedienungsanleitung

Draper

Draper PG950S Firmware-Update

PowerBoss

PowerBoss PowerBoss Bedienungsanleitung

SDMO

SDMO SH 4000 Bedienungsanleitung

EINHELL

EINHELL STE 5500 Bedienungsanleitung

Wanco

Wanco WI3000P Bedienungsanleitung

Full Boar

Full Boar FBT-3300 Bedienungsanleitung

Dwyer Instruments

Dwyer Instruments ASG Bedienungsanleitung

Westinghouse

Westinghouse WH1000i Series Bedienungsanleitung