Keysight Technologies E6640A EXM Installations- und Betriebshandbuch

Notice: This document contains references to Agilent.

Please note that Agilent’s Test and Measurement

business has become Keysight Technologies. For

more information, go to www.keysight.com.

Keysight E6640A EXM Wireless Test Set

Add Option E6640AU-TRX (add M9430A module)

Add Option E6640AU-TR4 (add M9431A module)

Add Option E6640AU-TR2 (add M9432A module)

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

E6640-90027

Edition

Edition 1, June 2015

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note E6640-90027 3

E6640AU-TRX/TR4/TR2 Module Add

STE 9000 software and test equipment is required for making adjustments and for performance

verification testing.

Information on how to obtain these calibration services can be found at:

www.keysight.com/find/calibration

There is no calibration required.

New TRX module additions are fully calibrated from the factory.

Products Affected: E6640A

Serial Numbers: All

Options:

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

( ) Customer

Estimated Installation Time:

Estimated Verification Time:

1.0 Hours

5 Minutes

4Installation Note E6640-90027

Introduction

The following instructions will guide you through the process of adding and an additional M9430A

TRX module into the E6640A main frame /chassis.

Table of Contents:

—Tools Required

—Remove Face Plate Panel

—Remove New TRX Module Filler Plate from Dress Panel

—Remove Impact Cover

—Remove Module Slot Fillers

—Install the TRX Module and Cable Connections

—Install Impact Cover and Dress Panel

—Enable the New TRX Module (in the XSA configuration file)

—Enable the New TRX Module (by sending a SCPI command)

—Update the FPGA Code

—Back Up New TRX Module Calibration Data to Hard Drive

—Run Self-Test Manual Verify

Tools Required

— T-10 TORX Driver

— T-20 TORX Driver

— #1 Phillip screwdriver

— Needle nose pliers

— Calibration Void if Broken sticker (PN: 7121-5432)

—USB keyboard and mouse

— E6640AU-TRX, -TR4, or -TR2 kit

Optional

— Cable removal tool (PN: 5002-3361)

Installation Note E6640-90027 5

Installation Procedure

The E6640A instrument has and Impact cover and face plate panel which cover access to the TRX

modules. The face plate panel and Impact cover frame needs to be removed to perform the module

addition. The following steps are based on the E6640A being a 2 up system.

Remove Face Plate Panel

1. Refer to Figure 1. Use the #1 Phillips screwdriver to loosen the 10 screws (1) on the edge of

the face plate panel till they spin freely. Use the T-10 TORX driver to remove the 4 screws (2)

in the middle of each TRX module. Then remove the 2 screws (3) on the Controller panel and

the Reference panel. Remove the face plate panel.

Figure 1 Face Plate Panel Screws

Electrostatic discharge (ESD) can damage or destroy electronic components. All

work on electronic assemblies should be performed at a static-safe workstation.

Observe proper procedures for performing static-safe work.

6Installation Note E6640-90027

Installation Procedure

Remove New TRX Module Filler Plate from Dress Panel

2. When adding an additional TRX module the filler panel will need to be removed. Refer to

Figure 2. Remove the 2 screws (1) that attach the filler panel (2) to the face plate.

Figure 2 Remove Filler Plate from Dress Panel

Installation Note E6640-90027 7

Installation Procedure

Remove Impact Cover

3. Tilt the main frame up in front by extending the front feet down.

4. Refer to Figure 3. After removing the face plate panel you will remove the 4 screws securing

the Controller panel (1) and the 2 securing the Reference panel (2). These can be moved

enough to allow the outer Impact cover to slide over them in the next step.

Figure 3 Controller and Reference Screws

8Installation Note E6640-90027

Installation Procedure

5. Refer to Figure 4. Remove the 4 screws (2) on each side of the Impact cover (1). This will

disconnect it from the chassis frame. Slide the Impact cover away from the chassis and over

the Controller and Reference panels which were disconnected in the previous step.

Figure 4 Impact Cover Screws

The Controller panel cover panel and Reference panel do not need to be

removed with the Impact cover. The Controller panel and the Reference

panel may be tilted in and the Impact cover slipped around them.

Removal of the Impact cover over the Controller panel requires you to

move the Impact cover towards the controller. This will allow you to tilt the

Controller sub-panel. See Figure 5.

Installation Note E6640-90027 9

Installation Procedure

Figure 5 Impact Cover Removal

On first production units and later, the Controller panel is mounted on the inside

of the Impact cover lip, so the tilting movement shown in the above picture will be

unnecessary.

10 Installation Note E6640-90027

Installation Procedure

Remove Module Slot Fillers

6. Refer to Figure 6. To gain access to the 4 Air blockers/ slot fillers you must first remove the 4

Filler Plates from Slot 3 of the main frame. Remove the 2 screws (1) for each Filler Plate. This is

where you will install your next TRX Module.

Figure 6 Filler Plate Removal

7. Refer to Figure 7. Remove the 4 Air blockers / slot fillers.

Inhaltsverzeichnis

Andere Keysight Technologies Prüfgeräte Handbücher

Keysight Technologies

Keysight Technologies 16380V Bedienungsanleitung

Keysight Technologies

Keysight Technologies 16034E Bedienungsanleitung

Keysight Technologies

Keysight Technologies 85059A Service-Handbuch

Keysight Technologies

Keysight Technologies IOT8700 Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies N4891A Bedienungsanleitung

Keysight Technologies

Keysight Technologies U1610/20A Bedienungsanleitung

Keysight Technologies

Keysight Technologies InfiniiVision 6000 X Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies 11645A Series Handbuch

Keysight Technologies

Keysight Technologies X Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies Infiniium V Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies 85051B Handbuch

Keysight Technologies

Keysight Technologies N9910X-888 Bedienungsanleitung

Keysight Technologies

Keysight Technologies 85054B Handbuch

Keysight Technologies

Keysight Technologies TN2870A Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies N5991 Bedienungsanleitung

Keysight Technologies

Keysight Technologies 85059V Service-Handbuch

Keysight Technologies

Keysight Technologies N5990A Bedienungsanleitung

Keysight Technologies

Keysight Technologies InfiniiVision MSO-X 4022A Handbuch

Keysight Technologies

Keysight Technologies MSO-X 2002A Bedienungsanleitung

Keysight Technologies

Keysight Technologies X Series Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies N4000A SNS Series Service-Handbuch

Keysight Technologies

Keysight Technologies PD1500A Installationsanleitung

Keysight Technologies

Keysight Technologies U2941A Bedienungsanleitung

Keysight Technologies

Keysight Technologies 1000A Series Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung