KI Basic Adjustable CPU Holder Bedienungsanleitung

Tools Provided:

•T-20 Torx Driver (#8 screw)

•T-30 Torx Driver (1⁄4"screw)

•3⁄32"Allen Wrench (set screw collar)

Tools Required:

•11⁄16"Open End Wrench,

•7⁄16"Open End Wrench or Socket

•Power Drill

•3⁄16"Drill Bit

Note: In some installations,

the CPU may not be available

for placement into the CPU Holder

until a later time. Follow these

directions using an accurate

measurement of the CPU height

and width as a guideline.

1. Position the glide plate under

the worksurface. Be sure that the

glide plate is parallel and placed

2" from the front edge of the

worksurface (1" on 24" deep

worksurfaces). Mark the four

mounting holes through the

plate onto the underside of the

worksurface (Figure 1).

2. Using a 3⁄16"drill bit to a maximum

depth of 3⁄4", drill the four mounting

holes in the underside of the

worksurface. Be careful not to

pierce through the top of the

worksurface when drilling the

holes. Attach the glideplate to the

worksurface with four 1⁄4x1" torx

head screws. Tighten each screw

only halfway, leaving the glide

plate to hang down 1⁄2"from the

surface (Figure 1).

3. Slide the slotted bracket over the

end of the glide plate. Tighten the

screws into the worksurface

(Figure 1).

Note: If the CPU is not available

to be placed into the holder until a

later time, skip step 4 and go onto

step 5, through 10. When a CPU is

to be installed along with the CPU

Holder, follow steps 4 through 10

but skip step 5.

Assembly Instructions

Basic Adjustable CPU Holder

August 2006

Assemble units as described herein only. To do otherwise

may result in instability. All screws, nuts and bolts must be

tightened securely and must be checked periodically after

assembly. Failure to assemble properly, or to secure parts

may result in assembly failure and injury.

1330 Bellevue Street • P. O. Box 8100 • Green Bay, WI 54308-8100 • Tel 1-800-424-2432 • www.ki.com

1⁄4x1"

torx head screw

3⁄16"hole

(3⁄4"deep max.)

slotted bracket

glide plate

Figure 1

7⁄16"nut, locking

&flat washer

side panels

(assembled)

7⁄16"carriage bolt (4", 7" and 10")

slotted bracket

side panels

(assembled)

Figure 3

upper side

panel

1⁄4"-20

acorn nut

lower side

panel

CPU

Figure 2

1⁄4-20

nut & washer

4. Carefully lay the CPU on its side

on a soft protective surface. Lay

the upper side panel onto the side

of the CPU. Lay the lower side

panel into the upper side panel to

fit the height of the CPU as tight

as possible. Tighten the side pan-

els together with two 1⁄4-20 acorn

nuts onto the studs. Repeat the

above procedure for the other pair

of side panels (Figure 2).

5. Have an accurate measurement

of the height of the CPU. Lay the

lower side panel onto the upper

side panel as illustrated. The

studs on the upper side panel

should go through the slots in

the lower side panel at or slightly

more than the measured height of

the CPU. Tighten the side panels

together with two 1⁄4-20 acorn nuts

onto the studs. Repeat step five

for the other pair of side panels

(Figure 2).

6. Position the assembled side

panels up into the slotted bracket.

Space the side panels to the

approximate width of the CPU and

finger tighten the four 1⁄4-20 nuts

and washers to hold the brackets

in place (Figure 3).

Note: If your installation does

not include placement of the CPU

into the holder at this time, follow

steps 7 through 10 using an

accurate measurement of the

width of the CPU. When the CPU

is installed, final adjustments and

tightening of hardware must be

done, closely following steps 7

through 10.

7. Choose the appropriate 7⁄16"

carriage bolt (4", 7" or 10") for

the CPU width. Insert the bolt

through the holes in the bottom

tabs of the side panels. Place a

washer and lock washer onto the

bolt. Screw the nut on just enough

to secure the side panels together.

Take the remaining two carriage

bolts and slide them into the

storage holes in the side of the

slotted bracket (Figure 3).

Assemble units as described herein only. To do otherwise

may result in instability. All screws, nuts and bolts must be

tightened securely and must be checked periodically after

assembly. Failure to assemble properly, or to secure parts

may result in assembly failure and injury.

Basic Adjustable CPU Holder

Assembly Instructions

7⁄16"carriage bolt

1⁄4-20

nut & washer

CPU

bottom tabs

Figure 4

#8 x 3⁄8"

torx screw

storage hole

slotted bracket

handle

unused

carriage bolts

Figure 5

8. Slide the CPU between the side

panels and allow it to rest on the

bottom tabs. Center the CPU front

to back. For 24" deep work-surfaces,

the CPU must be 1 1⁄2"forward of

center (Figure 4).

9. Press the side panels tightly against

the CPU. Tighten the four 1⁄4-20 nuts

on the slotted bracket and tighten

the nut on the bottom carriage bolt

(Figure 4).

10. Attach the handle to the slotted

bracket with four #8 x 3⁄8"torx head

screws (Figure 5).

Note: If a security kit is to be

installed to the CPU Holder, this

must be done prior to installing side

panel covers (separate instructions).

See assembly instructions for

Security Kit.

Assemble units as described herein only. To do otherwise

may result in instability. All screws, nuts and bolts must be

tightened securely and must be checked periodically after

assembly. Failure to assemble properly, or to secure parts

may result in assembly failure and injury.

Basic Adjustable CPU Holder

Assembly Instructions

Basic Adjustable CPU Holder

Assembly Instructions

Inhaltsverzeichnis

Andere KI Rack & Stand Handbücher

KI CFS01 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung