Kichler Lighting Richland II Bedienungsanleitung

 2*

 2*

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

Richland IITM

A Kichler®Select™

ceiling fan

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualified licensed

electrician.

3. WARNING: Suitable for use with solid-

state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting fixtures are not acceptable for fan

support and may need to be replaced,

consult a qualified electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only CUL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. Do not operate reversing switch while fan

blades are in motion. Fan must be turned

off and blades stopped before reversing

blade direction.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

the ground wire and white (common) wire

to one side with the black (load) wire to the

other side of the outlet box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be CUL Listed and marked suitable

for use with the model fan you are

installing. Switches must be CUL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

OR PERSONAL INJURY, MOUNT FAN TO OUTLET

BOX MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS (ALSO

REFERRED TO AS FLANGES) DURING ASSEMBLY

OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

1. SAFETY RULES

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

a. Fan blades (5)

b. Ceiling mounting plate

c. Motor and hanger bracket assembly

d. Motor housing

e. Set of blade brackets (5)

f. Mounting plate

g. Switch housing

h. Part bag contents

1) Mounting hardware:

wood screw, flat washer, spring washer,

star washers (2), wire nuts (3),

machine screws (2), washers (2),

screws (2)

2) Blade attachment hardware:

screws (17), washers (17),

fiber washers (17)

3) Safety cable hardware:

wood screw, lock washer, flat washer

4) Pull chain and fob

5) Balance Kit

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

Richland IITM

4. MOUNTING OPTIONS

If there isn't an existing UL (cUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 are examples of different ways to

mount the outlet box.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 3)

Outlet box

Fig. 1

Fig. 3

Outlet box

Fig. 2

Fig. 5

REMEMBER to turn off the power before you

begin.

To properly install your ceiling fan, follow the

steps below.

Step 1. Secure the ceiling mounting Plate to

the ceiling outlet box using screws and

washers included with your outlet box. (Fig. 4)

Step 2. Careful lift the fan motor and ceiling

mounting Plate assembly to the hanger plate

with the hook on the hanger plate for easy

installation. (Fig. 5)

Fig. 4

5. HANGING THE FAN

CUL Listed

electrial box

Flat washers

Mounting screws

Ceiling mounting

plate

Motor

Hook

Hanger plate

Ceiling mounting plate

Richland IITM

Fig. 6

6. MAKE THE ELECTRIC CONNECTIONS

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel.

Follow the steps below to connect the fan to

your household wiring. Use the wire

connecting nuts suppled with your fan. Secure

the connectors with electrical tape. Make sure

there are no loose wire strands or

connections.

Step 1. Connect the fan supply (black) wire

and light supply (blue) wire to the black

household supply wire as shown in Figure 6.

Step 2. Connect the neutral fan (white) wire to

the neutral household (white) wire.

Step 3. Connect the fan ground wire (green) to

the household ground wire.

Step 4. After connecting the wires, spread

them apart so that the green and white wires

are on one side of the outlet box and the black

and the blue wires are on the other side.

Step 5. Turn the connecting nuts upward and

push the wiring into the outlet box.

WARNING: TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK OR OTHER

PERSONAL INJURY, MOUNT YOUR

CEILING FAN ON A OUTLET BOX OR

SUPPORTING SYSTEM MARKED

"ACCEPTABLE FOR FAN SUPPORT".

BLUE

BLK BLK

GRN

Wiring

box

Ground to

mounting

bracket

or downrod

BLUE

FAN

LIGHT

Power lines 220~240V

Green ground

REDRED

BLK

Fig. 7

Fig. 8

8. INSTALLING THE MOTOR HOUSING

Remove the nuts and washers from the ceiling

mounting plate.

Place the wires and connections inside the

mounting bracket and the ceiling mounting

plate.

Swing the motor assembly up into position

under the ceiling mounting plate, align the

holes on the mounting bracket with the four

studs on the mounting plate and secure with

the nuts and washers just removed. (Fig. 7)

Washer

Ceiling mounting

bracket

Mounting

supports

Motor

Ceiling

mounting

plate

Mounting

studs

motor assembly

Nut

Washer Nut

Carefully lift the motor housing onto the ceiling

mounting plate.

The four mounting supports inside the motor

housing should be placed against the four

mounting studs on the outside of the mounting

plate.

Twist the housing clockwise until snug. (Fig. 8)

7. FINISHING THE INSTALLATION

Ceiling mounting

plate

Richland IITM

Fig. 9

9. ATTACHING THE FAN BLADES

Fig. 10

Step 1. Attach a blade to a blade bracket using

the screws, metal washers and fiber washers

provided. (Fig. 9)

Make sure the blade is straight when set on

the blade bracket. Tighten each mounting

screw and then repeat this procedure for each

blade.

Step 2. Attach each blade assembly to the

motor using the "Pre-Installed" mounting

screws in the blade bracket. (Fig. 9)

Set of blade brackets

Blades

Fiber washers

Washers

Screws

Mounting plate

Mounting ring

10. INSTALLING THE MOUNTING PLATE

1. Loosen two screws on the mounting ring

attached to the motor shaft and "remove" and

save the third screw. (Fig. 10)

2. Place the key holes on the mounting plate

over the 2 screws previously loosened from

the mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 10)

Richland IITM

Fig. 11

11. INSTALLING THE SWITCH HOUSING

NOTE: Before starting installation, disconnect

the power by turning off the circuit breaker or

removing the fuse at fuse box. Turning power

off using the fan switch is not sufficient to

prevent electric shock.

1. While holding the switch housing under your

ceiling fan, push the square wire connectors

together. One from the fan and one from the

switch housing.

NOTE: These connectors are color coded and

will ONLY engage when the colored strips are

matched (aligned).

2. Carefully push all the wires into the switch

housing.

Attach the switch housing to the mounting

plate with the screws provided. Make use

each screw is tight. (Fig. 11)

Switch

housing

Wire connector

Screws

Mounting plate

Fig. 12

Fig. 13

12. OPERATING INSTRUCTIONS

The pull chain controls the 3 speeds of your

ceiling fan.

1 pull = High, 2 pulls = Medium, 3 pulls = Low

and the 4th pull turns the motor off.

The Black Slide Switch on the side of the

switch housing controls the direction of the

blades "Forward and Reverse".

Warm weather - Forward (counter clockwise)

A downward airflow creates a cooling effect

as shown in Fig. 12. This allows you to set

your air conditioner on a warmer setting

without affecting your comfort.

Cool weather - Reverse (clockwise) An

upward airflow moves warm air off the ceiling

area as shown in Fig. 13. This allows you to

set your heating unit on a cooler setting

without affecting your comfort.

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Bentzen Bedienungsanleitung

Kichler Lighting

Kichler Lighting Maor 310136 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Leeds Bedienungsanleitung

Kichler Lighting

Kichler Lighting VASSAR Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ample Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk 330174OZ Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sunburst 300170 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 310155 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 inch Skye Bedienungsanleitung

Kichler Lighting

Kichler Lighting Select Sutter Place Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lacey Bedienungsanleitung

Kichler Lighting

Kichler Lighting Cameron Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35162 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Renew Select Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting Renew Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Fit Bedienungsanleitung

Kichler Lighting

Kichler Lighting Olympia Bedienungsanleitung

Kichler Lighting

Kichler Lighting Emerson HIGH COUNTRY Bedienungsanleitung

Kichler Lighting

Kichler Lighting Rana 310155 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Riggs 300143 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300395 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35166 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Arkwright Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300044 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung