Kicker VSS PWRA4P15 Bedienungsanleitung

PWRA4P15

Designed for 2015 and newer Jeep® Wrangler four door with premium audio

PWRA4P15-A1-20150224

Power Harness

Subwoofer Harness

Subwoofer

Amplifier

Assembly

Wire Ties x 6

T-Taps x 2

Fuse

12 channel Amplifier

Subwoofer

Assembly

Driver Selectable Surround

DSS (Driver Selectable Surround) mode can be turned on and off with the volume control knob on the

radio or steering wheel volume control buttons. DSS will give your music a new dimension by simulating a

surround sound feel. You can enable DSS by turning the volume control knob on the radio up two

increments and then down two increments within three seconds. You will hear a momentary attenuation in

the sound when the system switches to DSS mode. You can also enable DSS with the steering wheel

volume control buttons in the same way. Press the volume up button twice and then the volume down

button twice within three seconds. To disable DSS just repeat the same process.

Note: the balance is automatically controlled when you are in DSS mode. In fact, an easy way to tell

whether you are in DSS or non-DSS mode is to try the balance control. DSS can be utilized with any

source - i.e., Sirius® satellite radio, regular radio, and compact disc player.

KMS-1® or Kicker® Mobile Surround

If your vehicle is equipped with factory VES® (Video Entertainment System) you can enjoy the benefits of

KMS-1® (Kicker Mobile Surround).

KMS-1 is enabled automatically when the Radio is put into the VES® mode. This feature offers the

ultimate listening experience by providing surround sound uniquely equalized for your interior space.

Note: While in KMS mode the system automatically sets balance, fade and tone to provide the optimal

surround experience.

KMS® is available only if a DVD is in the player and the radio mode is set to VES®.

Fig. 2

Fig. 1

Fig. 5

Fig. 6

1. Disconnect negative battery cable

2. Gently pull out on the panel just below the steering column, rotate down and remove. Fig. 1

3. Remove the two 7mm screws (one on each side of the steering column) that secure the

radio/instrument bezel. Fig. 2

4. Remove the two screws securing the plastic panel below the steering column indicated by the

arrow in Fig. 3, and the one 7mm screw near the kick panel. Also, remove the two 10mm bolts

securing the metal plate and remove plate.

5. Remove the dash end panel by prying loose with a panel removal tool. Fig. 4

6. Remove the two screws securing the speaker housing. Fig. 5

7. Remove the 10mm bolt securing the speaker housing. Fig. 6

Fig. 4

Fig. 3

Fig. 11

8. Carefully pull the dash panel outward until there is sufficient room to allow access to remove

speaker housing and disconnect wiring.

9. Install the amp/bracket assembly into position as shown in Fig. 7 and secure the top of the

amp bracket using the supplied 10mm bolts.

10.Secure the bottom of the amp bracket using the supplied ¼” screw. Fig. 8

11.Install the sub amp into position by lining up the holes in the amp bracket with the two holes

for the bolts that retained the metal plate. Fig. 9

12.Install the supplied bolt into the bottom hole and leave loose. Fig. 10

13.Using a panel removal tool remove the four plastic retainers (three in front door opening and

one in rear door opening) securing the driver’s side sill plate and B pillar post cover. Fig. 11

14.Gently pull the kick panel/sill plate toward the brake pedal to release the fasteners securing it.

Fig. 10

Fig. 9

Fig. 7

Fig. 8

Fig. 15

Fig. 14

15.

Power Harness Installation

16.Find the rubber grommet in the top driver’s side of the fire wall underneath the hood and

remove it. Fig. 12

17.Using a razor knife make a small cut in the center of the grommet. Pass the power wire

through the grommet and pull the grommet up to the point where the plastic sheathing starts.

Fig. 13

18.Run the wire through the grommet hole in the fire wall and reinstall the grommet.

19.Run the wire along the top of the fire wall toward the battery and secure with wire ties.

20.Remove the top of the fuse cover and using a socket and ratchet loosen and remove the nut

on the positive battery accessory lug. Fig. 14

21.Connect the ring terminal of the power harness to the lug and retighten the nut. Torque to 10Nm.

22.Install the supplied black, two-pin connector by inserting the terminal on the end of the power

into the back of the connector, until it clicks and locks into place. Fig. 15

Fig. 13

Fig. 12

23.Remove the bolt securing the support brace under the steering column and connect the

subwoofer harness ground wire as shown in Fig. 16. Torque to 8Nm.

24. Locate the 16 pin connector on the amplifier behind the left front speaker housing. Find the

green/brown stripe wire and the gray/brown strip wire in this connector and install one of the

self-stripping t-tap connectors on to each wire. Lay the wire in the open channel, fold the

connector body over and squeeze with a pair of pliers until connector snaps shut. Fig. 17

25. Connect the green wire of the subwoofer harness to the gray/brown strip wire. Connect the

brown wire of the subwoofer harness to the green/brown stripe wire.

26.Connect the ten-pin connector of the harness to the amplifier. Slide the red locking tab

over to prevent the connector from accidentally coming disconnected.

27.Route the harness along the bottom of the front and rear door jam and toward the back

seat.

28. Run the wire harness along the floor under the rear seats to approximately the middle of the

vehicle and pull the end of the harness under the seat to the cargo area. Fig. 18

29. Set the subwoofer in place and connect the wire harness.

30. Rotate the rear seat back until it is nearly vertical. While holding the seat back with one hand,

slide the enclosure back until the hooks on the bracket are centered under the anchor points at

the bottom of the seat. Slowly rotate the seat back toward the rear of the vehicle until it locks

into place. Fig. 19

31. Reinstall all previously removed parts in reverse order.

32. Install supplied fuse in the fuse holder under hood.

33. Reconnect the negative battery cable. Torque to 5Nm.

Fig. 19

Fig. 18

Fig. 16

Fig. 17

Troubleshooting theKickerIntegrated Systems

IfyouexperienceaproblemoncetheSubwooferisinstalledusethisguidetolocatethetrouble.

Theradioisworking,buttheSubwooferisnotworking:

•Checkthebatteryvoltagetomakesureitisnotdischargedbelow11volts.

•Checkthenegativebatterycabletoseeifithasbeensecurelytightenedbackonthebattery.

•Checktheinlinefuselocatednearthebatterytomakesureitispluggedincompletely,andnot

blown.

•Checktheinline+12Voltpower-connectornearthefirewalltomakesureitispluggedinsecurely.

•Checktheinlineconnectorsnearthesubwooferenclosuretomakesuretheyarepluggedsecurely.

•Checkthegroundwireconnectiontomakesureitistightlysecuredtothepropergroundinthe

vehicle.

•Checktheaudioinputsignalconnectiontomakesureitissecurelyconnectedtothecorrectwiring.

•Testwithdifferentmusicincasethereisnolowfrequencyaudiointheinitialsoundcheck.

Thereisabuzzorrattlenoisethataccompaniesthe

lowfrequencyelementofthemusic:

•Checkforaconnectororanyotherobjectthatcouldbeverynearthesubwooferortheenclosure.

•Checkthesubwooferenclosuremountingbracketstomakesuretheyaresecure.

There is a problem with the multi-channel stereo amplifier:

•Checkthebatteryvoltagetomakesureitisnotdischargedbelow11volts.

•Checkthenegativebatterycabletoseeifithasbeensecurelytightenedbackonthebattery.

•Checkthemulti-pinconnectorsatthebackoftheradioandattheamplifierchassistomakesure

theyarepluggedallthewayin.

Symptom

Possible Cause

Solution

No Subwoofer Output

Fuse not installed in inline

fuse holder on subwoofer

and/or amp harness

Install fuse(s) into fuse holder(s). Refer to

instructions for correct placement

Low battery voltage

Recharge the battery

Negative batterycable not

connected

Reconnect negative battery cable

Power wire connector not

connected to body harness Connect power wire to body harness. Check

for loose connection

Ground wire not grounded

properly Check ground wire with voltmeter to insure it is

a good ground

Signal input connector not

connectedproperly

Connect signal wire of subwoofer harness to

signal wire of amplifier harness or factory

speaker wire depending on application.

Check for loose connection

Balance or fader controls not

set to neutral position

Set balance and fader control to center

settings. (only affects stand alone subwoofer

kit)

No low frequency

information in music

Test with several different songs

Subwoofer harness not

properly/completely

connected to subwoofer.

Securely fasten both of the connectors on the

subwoofer harness to the subwoofer. Check

for loose connections.

Radionotcomingon

Radio connector not

properly/completely

connected

Check radio connector to insure it is

completelyseated

Blown radio fuse Refer to owner's manual for radio fuse location

and value

Low battery voltage

Recharge the battery

Radiocomeson,butno

sound from any speakers

Fuse not installed in inline

fuse holder on amplifier

harness

Install fuse into fuse holder. Refer to

instructions for correct placement

Radio connector not

properly/completely

connected

Check radio connector to insure it is

completelyseated

Ground wire not grounded

properly Check ground wire with voltmeter to insure it is

a good ground

Low battery voltage

Recharge the battery

If you continue to experience problems after troubleshooting with this list, please contact KICKER®

Technical Support at (800) 256-0808 ext. 6009, or support@kicker.com.

Andere Kicker Subwoofer Handbücher

Kicker

Kicker SOLO-BARIC S10L3 Bedienungsanleitung

Kicker

Kicker S18XSP Bedienungsanleitung

Kicker

Kicker CompVR CVR15 Bedienungsanleitung

Kicker

Kicker CompVX CVX15 Bedienungsanleitung

Kicker

Kicker subwoofer ES104 Bedienungsanleitung

Kicker

Kicker TCVR10 Bedienungsanleitung

Kicker

Kicker Solo-Baric S8L7 Bedienungsanleitung

Kicker

Kicker Amphitheater BTL Bedienungsanleitung

Kicker

Kicker SubStation PES10C Bedienungsanleitung

Kicker

Kicker SWRA211 Bedienungsanleitung

Kicker

Kicker SOLOX Bedienungsanleitung

Kicker

Kicker PSUTA15 Bedienungsanleitung

Kicker

Kicker CompVR DCVR10 Bedienungsanleitung

Kicker

Kicker Solo-Baric S15L5 Bedienungsanleitung

Kicker

Kicker CompVX Series Bedienungsanleitung

Kicker

Kicker Solo-Baric L7-Series Bedienungsanleitung

Kicker

Kicker Solo-Baric S1L7 Bedienungsanleitung

Kicker

Kicker COMPETITION C18c Bedienungsanleitung

Kicker

Kicker PSON13 Bedienungsanleitung

Kicker

Kicker KMW10 Bedienungsanleitung

Kicker

Kicker Hideaway HS8 Bedienungsanleitung

Kicker

Kicker Comp DC12 Bedienungsanleitung

Kicker

Kicker SubStation PES10C Bedienungsanleitung

Kicker

Kicker ZX350.2 Bedienungsanleitung

Beliebte Subwoofer Handbücher anderer Marken

Sony

Sony XS-AW8 Bedienungsanleitung

Sony

Sony XS-L836 Bedienungsanleitung

B&C Speakers

B&C Speakers 15 HPL 76W Bedienungsanleitung

Velodyne

Velodyne DD-18+ Bedienungsanleitung

Sonance

Sonance Cinema Series SUB 10-150 Bedienungsanleitung

Hifonics

Hifonics HW-12 Kurzanleitung

Magnat Audio

Magnat Audio ADR 130 BP Bedienungsanleitung

Blitz

Blitz BZP106 Bedienungsanleitung

Technics

Technics SB-AS500 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-2 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-3 Bedienungsanleitung

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Bedienungsanleitung

REL Acoustics

REL Acoustics Q Series Bedienungsanleitung

Pioneer

Pioneer Elite S-W1EX Bedienungsanleitung

L-Acoustics

L-Acoustics KIVA SB15M Kurzanleitung

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Bedienungsanleitung

KEF

KEF KUBE 200 Bedienungsanleitung

Yamaha

Yamaha SW500 Bedienungsanleitung