Kielder KWT-355 Benutzerhandbuch
ORIGINAL INSTRUCTION MANUAL
For use with all variants of KWT-355 Digital Tyre Pressure Gauge
KWT-355
Kielder
DIGITAL TYRE PRESSURE GAUGE
www.kielder.co
KWT-355-IMA21
2
KWT-355-IMA21 Kielder WT Ltd
INSTRUCTIONS
NOTES:
1. Pressure HOLD feature is disable from
factory. To enable pressure HOLD
feature, please see check valve spring
assembly instructions.
2. When taking tyre pressure measurement
do not remove air chuck from valve. See
step 4 for correct method.
STEPS
1. Consult your vehicle’s manual for
correct tyre pressure. Check pressure
when tyres are cool.
2. Push “On” button gauge comes on
with lighted display This gauge reads
in four dierent units: PSI, BAR & KPA,
KGF/CM2 and should display “0” when
on standby in any of these units.
3. To select a dierent unit, press “UNIT”
button and see bottom side of display
until desired unit has been selected.
4. Press valve connector rmly onto tyre
stem ensuring no air leakage. The
exact air pressure value of your tyre
will be displayed.
5. To check the next tyre. REPEAT
steps 4
6. The display will remain ON for
proximately 2 and a half minutes and
automatically switch OFF.
7. Backlight stays on for 1 minute.
8. If pressure reading seems unusually
low, repeat above steps, ensuring that
no air escapes between gauge chuck
and tyre valve stem.
BATTERY MAINTENANCE
To replace the battery, remove the
rubber covering. Then slide both battery
compartments out to reveal 2 CR2032
batteries.
3
Kielder WT Ltd KWT-355-IMA21
FEATURES
AUnits display
BPressure display
C On / o button
DUnit button
EPressure release button
A
B
C
D
E
4
KWT-355-IMA21 Kielder WT Ltd
Warranty & Support
The Kielder 1 Year Warranty
Warranty Statement
• Each Kielder product is thoroughly
inspected during production and is
guaranteed to perform as specied. The
product will be free of defects, in both
workmanship and materials, for the duration
of the warranty from the date the product is
purchased.
• The warranty becomes eective at the
date of purchase (or the date of delivery if
this is later).
• In the event that your gauge needs
repairing or replacing, you must provide
proof of purchase/delivery before any
work can be carried out on your gauge.
Without this, any work carried out may be
chargeable.
• If your product requires attention from
our engineers, we aim to have it collected &
repaired within 7-10 working days.
• The repair or replacement of your gauge
under warranty will not extend the period of
warranty.
• The warranty provides benets which are
additional to and do not aect your statutory
rights as a consumer.
What is covered?
• The repair or replacement of your guage
(at Kielder’s discretion), if your gauge is
found to be defective due to faulty materials,
workmanship or function within the warranty
period (if any part is no longer available or
out of manufacture, Kielder will replace it
with a functional replacement part).
• Use of the gauge in the UK only, overseas
users should contact the ocial importer or
retailer for that country.
What is not covered?
• Kielder does not guarantee the repair or
replacement of a product incurred as a result
of normal wear and tear. this includes any
moving parts which are prone to wear and
tear, over time.
• Accidental damage, faults caused by
negligent use or care, misuse, neglect,
careless operation or handling of the
product which is not as instructed in
Kielder’s Instruction manual.
• Batteries are excluded from the 1 Year
warranty.
• Use of parts which are not assembled or
installed in accordance with the instructions
of Kielder.
• Use of parts which are not Kielder
genuine components.
• Repairs or alterations carried out by
parties other than Kielder.
How to contact Kielder
If you have any queries over your product,
please don’t hesitate to contact us via:
tools@kielder.co
or call customer services on:
0114 242 3794.
...and we’ll be happy to help.
5
Kielder WT Ltd KWT-355-IMA21
SPECIFICATION
SERVICE: Compatible gases
ACCURACY: +/- 1% FS, Grade A, ANSI/
ASME B40.7
RESOLUTION: 0.1 PSI
PRESSURE RANGE: 0 to 150 PSI (0.21
to 10.34 Bar)
TEMPERATURE LIMITS: 0 to 100 degree
F (-17.8 to 37.8 C)
CONNECTION: Tyre valve stem or
equivalent
DISPLAY: 3-1/2 digit, 3/8- LCD with
backlight
SCREEN SIZE: 1.50” measured
diagonally
CALIBRATION: To ensure accurate
readings we recommend calibrating your
tool with us once a year
SHUTOFF: 90 second
POWER REQUIREMENTS: (2) CR2032
battery, installed functional, user
replaceable.
WEIGHT: Hose style: 8oz (230g)
1 year warranty
KIELDER
Distributed by KIELDER WT
www.kielder.co
Designed in the UK
- Made in China
KWT-355-IMA21 Kielder WT Ltd
Kielder
KIELDER WORKS TEAM
WT
Kielder WT Ltd
Sheeld, UK
T: +44 (0)114 242 3794
E: tools@kielder.co
W: http://www.kielder.co
Registered in England & Wales: 09426163
Kielder Tools
Inhaltsverzeichnis
Andere Kielder Werkzeuge Handbücher
