KIMBALL MIDWEST 84-150 Bedienungsanleitung

Operating Instructions Manual

0.5HP 5-in-1 Pneumatic Tool Kit

84-150

Read through this operating instructions manual carefully before using

the product. Protect yourself and others by observing all safety

information, warnings, and cautions. Failure to comply with instructions

could result in personal injury and/or damage to product or property.

Please retain instructions for future reference.

SPECIFICATIONS:

AIR SUPPLY:

Tools of this class operate at a wide range of air pressure. It is recommended

that the dynamic air pressure be maintained at 90 PSI at the tool. Higher

pressure and unclean air will shorten the tool’s life due to accelerated wear

and may create a hazardous condition.

Water in the air line will cause damage to the tool. Drain the air tank daily.

Clean the air inlet filter screen at least weekly.

The air inlet, used for connecting the air supply, has a standard 1/4” NPT

thread.

Line pressure should be increased to compensate for pressure drops in air

hoses over 25’ in length.

OPERATING INSTRUCTIONS:

To remove tools from the air motor body, remove the air supply and pull back

the locking collar, as indicated by the arrow, and pull the tool head off of the air

motor.

To install tools onto the air motor body, simply pull back the locking collar and

push the tool head onto the air motor body. Once the tool is seated, release the

locking collar and reconnect the air supply

An external air regulator can be used as an air throttle and can be used for

setting positive speed control.

Have the throttle in the “off” position when connecting the tool to the air supply.

Disconnect the tool before performing service, changing drill bits and when not

in use.Always use the tool a safe distance from other people in the work area

Airline Setup (components not included):

WARNING: Cancer and Reproductive Harm – www.p65warnings.ca.gov.

SAFETY PRECAUTIONS:

1. Make sure the RPM rating of the drill bit and abrasives are compatible

with the free speed of the tool. Over-speeding an accessory is dangerous

and can cause personal injury.

2. Disconnect the tool before performing service, changing accessories, or

when not in use.

3. Always use the tool a safe distance from other people in the work area.

4. Keep the tool away from your body when it is running. Do not wear loose

or ill-fitting clothing; remove watches and rings.

5. Secure the work with clamps or a vise so both hands are free to operate

the tool. Don’t overreach. Keep proper footing and balance at alltimes.

6. Maintain tools with care. Keep tools clean and oiled for the best

performance. Follow the instructions for lubricating and changing

accessories. Wiping or cleaning rags and other flammable waste

materials must be disposed of as per local, state and federal regulations.

LUBRICATION:

Lubricate the tool daily with a high quality air tool oil. If no air line oiler is used,

run a teaspoon of oil through the tool. The oil can be added into the tool air

inlet or into the hose at the nearest connection to the air supply, then run the

tool.

MAINTENANCE:

Other factors outside the tool may cause loss of power. Reduced compressor

output, excessive draw on the air line, moisture or restriction in air lines or the

use of hose connections of improper size or poor condition may reduce the air

supply. Grit or gum deposits in the tool may reduce power and may be

corrected by cleaning the air strainer and flushing out the tool with Ultra Guard

Extreme Air Tool Conditioner [K-M No. 80-293 or 80-291] or Power+ Air Tool

Conditioner [K-M No. 80-769].

REPAIR & SERVICING:

For tools out of warranty Kimball Midwest carries a General Maintenance Kit

[K-M No. 84-151]. Tools can also be serviced by Power Tool Repair (371

West Ave. Tallmadge, OH 44278, 330-630-0022).

LIMITED WARRANTY:

Kimball Midwest warrants to the original buyer ("Buyer") all parts and

accessories purchased by it from Kimball Midwest against defects in material

or workmanship.

Kimball Midwest will repair or replace, at no charge to the buyer, this tool which,

after examination by Kimball Midwest, is determined to be defective within a

period of 1 year from receipt.

Coverage under this warranty will be provided only if the defective tool has

been submitted to Kimball Midwest for inspection.

This warranty does not cover any damage to this tool due to alteration,

modification, improper installation, accident, post-installation misuse, abuse,

negligence, inadequate maintenance, or malfunction of associated parts or

equipment not supplied by Kimball Midwest.

This warranty is in lieu of any other warranty, expressed or implied, including

any warranty of merchantability or fitness for a particular purpose.

Replacement or repair as provided under this warranty is the exclusive remedy

of the buyer. Kimball Midwest shall not be liable for any incidental or

consequential damages resulting from breach of this warranty. Kimball

Midwest neither assumes, nor authorizes any person to assume for it, any

other liability in connection with the sale of its products.

If this Kimball Midwest Product proves defective in material or workmanship

within one year after purchase, contact the Kimball Midwest Quality Assurance

Department at All-QualityAssurance@kimballmidwest.com

Exploded View & Parts List

NOTES:

Manufactured For:

Kimball

Midwest

4800 Roberts Road

Columbus, OH 43228

1-800-233-1294

www.kimballmidwest.com

Inhaltsverzeichnis

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung