Kimo C310 Bedienungsanleitung
Configuration of C310 multifunction
transmitters by keypad
Table of contents
1. Introduction..........................................................................................................................................5
1.1. Description of the transmitter.......................................................................................................5
1.2. Description of the keys.................................................................................................................5
1.3. Protection tips of the sensor........................................................................................................6
2. Modbus................................................................................................................................................7
2.1. Confi uration of parameters........................................................................................................7
2.2. Functions......................................................................................................................................7
2.3. Access code to re ister................................................................................................................7
3. Confi ure the transmitter...................................................................................................................10
3.1. Enter the security code..............................................................................................................10
3.2. Set the parameters of the transmitter........................................................................................10
3.2.1 Set the screen......................................................................................................................11
3.2.2 Set the raphical period.......................................................................................................11
3.2.3 Set the lan ua e..................................................................................................................11
3.2.4 Set date and time.................................................................................................................11
3.2.5 Activate /deactivate the beep key........................................................................................11
3.2.6 Lock and unlock the keyboard.............................................................................................11
3.2.7 Modify the security code......................................................................................................12
3.2.8 Back to factory parameters..................................................................................................12
3.2.9 Set the Modbus (optional)...................................................................................................12
3.2.10 Set the Ethernet communication (optional).......................................................................12
3.2.11 Access to the transmitter information................................................................................13
3.3. Confi ure the measurement channels.......................................................................................13
3.4. Confi ure the analo ue outputs.................................................................................................13
3.4.1 Select the type of output......................................................................................................13
3.4.2 Set the minimum and maximum ran es..............................................................................14
3.4.3 Perform an output dia nostic...............................................................................................14
3.5. Confi ure the alarms..................................................................................................................15
3.5.1 Select the alarm mode.........................................................................................................15
3.5.2 Set the alarm in risin or fallin ed e..................................................................................16
3.5.3 Confi ure the alarm in monitorin mode.............................................................................16
3.5.4 Confi ure the alarm on Transmitter state mode..................................................................16
3.5.5 Confi ure the relays (optional)............................................................................................17
3.6. Confi ure the probes, boards and normative values.................................................................18
3.6.1 Confi ure an air velocity and airflow probe.........................................................................18
3.6.2 Confi ure a CO2 probe or a temperature/hy rometry probe..............................................19
3.6.3 Confi ure a board................................................................................................................19
3.7. Activate an option.......................................................................................................................22
4. Description of function and Modbus connections.............................................................................24
4.1. Device........................................................................................................................................24
4.2. Channels....................................................................................................................................24
4.3. Outputs.......................................................................................................................................25
4.4. Alarms........................................................................................................................................26
4.5. Measurement parameters..........................................................................................................26
1. Introduction
1.1. Description of the transmitter
C310 transmitters with display can be configured via keypad. It is possible to set the measurement units, to activate or not a
channel,...
Trend indicator : on the screen, a trend indicator represented by a rising arrow, a going down arrow or a stable arrow is
displayed above the measurement unit. It means the calculation of a moving average on the last hour ( 1) to compare with
a moving average on the last 5 minutes ( 2) :
•If 1 = 2, the trend is stable.
•If 1 < 2, the trend is upwards.
•If 1 > 2, the trend is downward.
This trend indicator is displayed after 5 minutes.
Indicator light : the indicator light indicates that the transmitter if powered on.
1.2. Description of the keys
–Up key : increments a value, allows to browse through the menus
–Down key : decrements a value, allows to browse through the menus
–Left key : allows to browse through the menus
–Right key : allows to browse through the menus
–OK key : validates an input, allows to enter in the main menu
–Esc key : cancels an input or backs to the previous step
5
Right key
Down key OK key
Left key Indicator light
C1 9
Pa
Graphique►
Mesures Alarm lights
Up key
Input probe 1 Input probe 2
C2 35
%RH
◄Min/max
05/02/14 9.53
Esc key
1.3. Protection tips of the sensor
It's extremely unwise to remove the protection tip of our hygrometry probes as
the sensitive element is very fragile even to light contacts. However, if you
have to remove the protection tip, take all possible precautions and avoid any
contact with the sensitive element.
To remove the protection tip, unscrew it or unclip it.
6
Protection tip
to unscrew
Protection tip
to unscrew
Sensitive
element
Sensitive
element
2. Modbus
2.1. Configuration of parameters
•Comm nication speed : between 2400 and 115200 bauds, 19200 bauds by default
•Data bits : 8 bits
•Stop bit : 1 bit
•Parity : None
•Flow control : None
•Transmitter addressing : between 1 and 255 (automatically answers the requests from address 0)
2.2. Functions
•Register f nction : Function 03
•Register writing : Function 16
•Comm nication loop test : Function 08
2.3. Access code to register
•Registers type:
Type Size Detail
Serial number 8 octets Data organization
U8 1 octet 8 bits unsigned integer
U16 2 octets 16 bits unsigned integer
U32 4 octets 32 bits unsigned integer
Real 4 octets 32 bits real
Enumeration 1 octet See table “Enumerations”” pError: Reference source not found
Boolean 1 octet True = 1 ; False = 0
Date 4 octets Year (2 octets), onth (1 octet), Day (1 octet)
Time 5 octets Hour (1 octet), inute (1 octet), Second (1 octet), illisecond (2 octets)
•Alarms stat s – odbus code : 7000
b31 … b4 b3 b2 b1 b0
0 1 0 1
•Val es – odbus code : 7010 (channel 1)
7040 (channel 2)
7070 (channel 3)
7100 (channel 4)
•N mber of digits after the decimal point – odbus code : 7020 (channel 1)
7050 (channel 2)
7080 (channel 3)
7110 (channel 4)
7
Alarm channel 1
Alarm channel 2
Alarm channel 3
Alarm channel 4
•Unit – odbus code : 7030 (channel 1)
7060 (channel 2)
7090 (channel 3)
7120 (channel 4)
List of nits :
Field Unit Val e Field Unit Val e
None 0 None 0
Temperat re °C 16
Air velocity
m/s 64
°F 17 fpm 65
Hygrometry
%HR 32 km/h 66
G/Kg 33
Airflow
m3/h 80
Kj/KG 34 L/s 81
°C td 35 cfm 82
°F td 36 m3/s 83
m3/h 80
°C Tw 37 Comb stion ppm 112
°F Tw 38
Electricity
mV 160
Press re
kPa 50 V 161
inWg 51 µA 162
hPa 52 mA 163
mbar 53 A 164
mmHg 54
mmH2O 55
daPa 56
Pa 57
Example of a meas rement at 24.2 °C :
•Value : code 7010, real type ( ost Significant Byte / Least Significant Byte)
Byte 3 Byte 4 Byte 1 Byte 2
b15 b16 b31 b24 b7 b0 b15 b8
0100 0001 1100 0001 1001 1001 1001 1010
Val e : 24.2
•Number of digits after the decimal point : code 7020, U8 type
Byte 1
b7 b0
0000 0001
N mber of digits after the decimal point : 1
8
•Unit : code 7030, U8 type
Byte 1
b7 b0
0001 0000
Unit val e : 16 : °C (See table “List of nits” p8)
“En merations” table :
Corresponding val es 0 1 2 3 4 5 6 7
Backlight d ration Off 10s 30s 60s Permanent
Graphical period 3 mn 15 mn 30 mn 1 hour 3 hours 6 hours 12
hours
24
hours
Lang age French English Third language
Date Format dd-mm-yyyy mm-dd-yyyy yyyy-mm-dd
Time Format 24H 12H
Modb s Com speed 2400 4800 9600 19200 38400 115200
Channel x Unit See list of unit
Channel x Transmitter none probe 1 probe 2 module
O tp t x Type 4 - 20 mA 0 - 20 mA 0 - 10 V 0 - 5 V 0 - 1 V
O tp t x Diagnostic Deactivate 0% 50% 100%
Inp t x Type 4 - 20 mA 0 - 20 mA 0 - 10 V 0 - 5 V 0 - 1 V
Alarm x Mode Deactivate Rising edge Falling edge onitoring Transmitter
state
Alarm x Sec rity Negative Positive
Relay x Selection OFF ON Alarm 1 Alarm 2 Alarm 3 Alarm 4
Compensation Temperat re :
Unit °C °F
Compensation Temperat re :
Mode Value Thermocouple Probe N°1
Compensation Press re :
Unite hPa mbar mmHg m (alt)
Compensation Normative val e None DIN1343 ISO2533
Débit Press re nit
for airflow Pa mmH2O inWg mbar
Moy. Mes re Differential
press re device Pitot L Pitot S Debimo blades Factor
Section Type Rectangular Circular Coefficient
Section Unit mm inch
9
3. Configure the transmitter
3.1. Enter the security code
To configure the transmitter, and for security purposes, a security code must be entered. The default code is 0101.
➢Connect the transmitter.
➢Wait until the initializing period is over.
➢Press OK.
“Code” is displayed with “0000” below.
➢Press OK to go to the second zero.
➢Press Up key to display 1 then press OK.
➢Press OK to go to the 4th zero.
➢Press Up key to display 1 then press OK.
The configuration screen is displayed.
This screen allows to set :
•the transmitter
•the channels
•the analogue outputs
•the alarms
•the relays
•the configurations
•the options
If a wrong code is entered, the following message is displayed : “Bad code”. Press OK to go back to the
measurement screen then press OK to enter the code again.
3.2. Set the parameters of the transmitter
This part allows to set :
•the screen : contrast and backlight
•the graphical period : during”X” last minutes, the transmitter displays the measured values as a graph
•the language : French or English
•the date and time
•the beep key
•the keypad locking
•the safety code : modify the access code
•back to factory configuration
•the odbus
•the Ethernet
•Information : get an access to information about the transmitter and the connected probes
➢Enter the security code then press OK.
➢Press OK on “Device” line.
The screen allowing to configure the transmitter is displayed.
10
Code ?
0101
Inhaltsverzeichnis
Andere Kimo Sender Handbücher
Kimo
Kimo Class 300 Bedienungsanleitung
Kimo
Kimo CPE 311-S Bedienungsanleitung
Kimo
Kimo Class 200 Bedienungsanleitung
Kimo
Kimo CA 310 Bedienungsanleitung
Kimo
Kimo ATE 310 Bedienungsanleitung
Kimo
Kimo CP 111 Bedienungsanleitung
Kimo
Kimo 210-R Series Bedienungsanleitung
Kimo
Kimo TG 100 Bedienungsanleitung
Kimo
Kimo HM 50 Bedienungsanleitung
Kimo
Kimo CPE 300 Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
