Kinderkraft JUNIOR FIX 2 i-Size Bedienungsanleitung

MODEL: I-LITE ECE.R129.03 ver. 1.0

SAFETY FIX 2

i-Size

USER GUIDE

MODEL: SAFETY FIX 2 i-Size ECE R129.03 v.1.0

ATTENTION! Product graphics serve an illustrative function.

A.1

Please read the operating manual carefully before using the child car seat for the first time.

Ensuring the safety of the child is your responsibility, and not reading this instruction may have an

impact on it.

1.0 Car seat components

1. Headrest

2. Internal pad

3. Removable internal safety harness pads

4. Internal safety harness

5. Internal safety harness buckle

6. Buckle pad

7. Button for adjusting the internal safety harness

8. Strap for adjusting the internal safety harness

9. Seat

10. Headrest height adjustment lever

11. Shoulder safety harness guide

12. Internal car seat insert

13. ISOFIX release button

14. ISOFIX connector arms

15. ISOFIX identifiers

16. Top-Tether strap

17. Top-Tether strap buckle



























 



Hight of the child

Car seat setting

Car seat mounting

Securing the child

in a car seat

76cm - 105cm

/≤18kg

forward

facing

ISOFIX + Top Tether

Internal safety

harness

100cm - 150cm

forward

facing

ISOFIX + three-

point car seat belt

three-point car

seat belt

three-point car

seat belt

three-point car

seat belt

2.0 Usage

The car seat has been designed, tested and approved for use in accordance with the requirements of

UN/ECE Regulation No. 129 concerning the approval of child improved restraint systems (UN/ECE

R129/03).

The SAFETY FIX 2 i-Size car seat is designed for children from 76 cm to 150 cm in height and can be

installed facing forward. In the range from 76 cm to 105 cm and up to 18 kg, the car seat is installed

using the ISOFIX connectors and the Top Tether strap. In this range, the child is held in the car seat by

the internal safety harness. In the range from 100 cm to 150 cm, the car seat is installed using ISOFIX

connectors and three-point car seat belt or using a three-point car seat belt. In this range, the child is

held in the car seat by a three-point car seat belt.

The car seat can be installed in the car in the places indicated by the manufacturer in the vehicle

manual. It is required to read the vehicle manufacturer's operating instructions.

A.2

A.3

3.0 Safety instructions

WARNINGS

Please take a few minutes to read this instruction manual in order to ensure the proper security of your

child. Many injuries that are easy to avoid are caused by reckless and improper use of the car seat.

• The car seat is designed to be mounted only on forward-facing seats. The car seat must not be

mounted on rearward facing or side facing seats (fig. A.2, A.3).

• If the car seat is installed in the front seat, the front air-bag must be deactivated. It is recommended

to install the car seat only on the back seats of the car. Please refer to your vehicle operating manual

for information on the suitability of the seat for use with a car seat.

• Remember that the internal safety harness holding the child should be adapted to the child's body

shape and not twisted. For this reason, child should not wear thick clothes under the safety harness.

• The car seat waist belts must run as low as possible across your child's pelvis to ensure optimum

effect in the event of an accident.

• The car seat should be replaced when it has been subjected to violent stresses during a traffic

accident.

• The car seat may not be modified in any way without the acceptance of the relevant approval

authority. Failure to install the car seat in accordance with the manufacturer's instructions may pose a

threat to life and health.

• Protect the car seat from direct sunlight, otherwise your child may be burnt by heated parts. Protect

your child and car seat from sunlight.

• Never leave your child unattended in the car seat.

• Make sure that the luggage and other objects are adequately secured, in particular on the parcel

shelf, as they can cause injuries in the event of a collision.

• The car seat cannot be used without the cover.

• Do not use replacement covers, other than those recommended by the manufacturer, as the

cover is an integral part of the safety system of the car seat.

• Do not use any other attachment points than those described in the instruction manual and

marked on the car seat.

• All hard elements and plastic parts of the child car seat should be placed and installed in a way

that, under normal vehicle operating conditions, they cannot get trapped by the sliding seat or

vehicle doors.

• Regularly check the technical condition of the car seat, pay special attention to the fixing

points, seams and adjusting elements. It is important to ensure that all mechanical elements are

fully operational. Never grease or oil parts of the car seat.

• Do not use the car seat if its parts are damaged or loose.

• In the event of an emergency, it is important to quickly unfasten the car seat belt. This means

that the release button of the safety harness is not fully secured; make sure your child does not

play with the safety harness.

• Set a good example for your child and wear your car seat belt at all times. An adult who is not

fastened with a car seat belt can also pose a threat to a child.

• Make sure that the car seat is correctly fastened before each journey in the car.

• The car seat must be secured at all times, even when not in use. The car seat that is not

fastened can injure the passengers even during emergency braking.

• On some vehicle seats made of delicate materials, the use of car seats may leave marks and/or

discolouration. To prevent this from happening, you can place a blanket, towel or similar product

under the car seat.

B.1

B.2

4.0 Securing the child

4.1 Use of insert

The baby insert (fig. B.1, item 12) improves comfort and gives extra support for young children. We

recommend using the lower part as well as the upper part, which serves as a pillow for the child's

head until the child needs more space in the car seat. Then the inserts should be removed.

4.2 Installation of insert

•Unfasten the internal safety harness (4) by pressing the red button on the buckle (5).

•Place the insert (12) in the car seat so that it adheres to the sides.

•Adjust the position of the internal safety harness. Check whether the safety harness is not twisted.

(fig. B.2)

•Using a strap, place the upper part of the insert on the headrest.

C.1 C.2

C.3 C.4

5.0 Using the car seat

5.1 Adjusting the position of the internal safety harness and

the headrest

The adjustment of the car seat safety harness is integrated with the adjustment of the headrest. The

headrest should be adjusted according to the child's height. The height of the safety harness will

change with the height of the headrest. Before changing the position of the headrest, loosen the

inner belts (4) by pressing the adjustment button (fig. C.1, item 7) while pulling the shoulder straps

towards you (fig. C.2).

A correctly positioned headrest ensures optimal placement of the shoulder part of the vehicle seat

belt and provides protection and comfort for your child. NOTE Adjust the appropriate height of the

shoulder safety harness so that the harness enters the seat backrest slightly above the child's

shoulders (fig. C.4).

• To raise the headrest and shoulder safety harness, grasp the headrest adjustment lever (1) located

on the back of the headrest (1) and pull it gently upwards. The headrest will be unlocked.

• The headrest (1) can now be adjusted to the desired height (fig. C.4). When the height is adjusted,

let go of the adjustment lever (10) - the headrest will be locked after slightly adjusting the height up

and down.

IMPORTANT! Make sure the seat headrest is locked in place.

• In order to lower the headrest and shoulder safety harness, pull the headrest adjustment handle

(10) and lower the headrest. The headrest and shoulder safety harness will be lowered at the same

time.

ATTENTION! Proper adjustment of the headrest height has a direct impact on the child's safety.

Place the car seat on the vehicle seat. Place your child in the car seat and check the height of the

headrest. Attention! If necessary, repeat the steps to adjust the headrest height until you reach the

optimal height.



D.1

D.3

D.2

5.2 Securing the child with the internal safety harness

• Loosen the internal safety harness fully by pressing the button (4) and pulling the safety harness

straps (fig. B.8).

• Undo the buckle (5) and place the internal safety harness on the sides of the car seat (fig.B.8). Place

the child in the car seat (fig. D.1).

• Adjust the headrest to the child's height (see section 5.1).

• Bring the two buckle latches together to engage them and insert them into the buckle (5) until you

hear a "click" (fig. D.2).

5.3 Tightening the internal safety harness

• Pull the shoulder straps to eliminate slack in the waist section, so the internal safety harness will lie

flat.

• Tighten the internal safety harness with the adjustment strap (7) until it lies flat on the child's body

and close to it (fig. D.3).

NOTE The waist internal safety harness straps must be positioned as low as possible on the child's hips.

Make sure that the internal safety harness is not twisted.

E.1

6.0 Installation in the car

In the event of sudden braking or an accident, people not wearing car seat belts may injure other

passengers.

Always check whether:

• The seat backrests in the vehicle are locked (i.e. the folding backrest of the rear seat is latched).

• All heavy and sharp-edged items are secured (e.g. on the rear shelf).

• All passengers have fastened their car seat belts.

• The car seat is always secured even if the child is not transported in it.

6.1 Installing a forward-facing car seat for children between

76 and 105 cm tall using the ISOFIX system and the Top-

Tether).

IMPORTANT The vehicle manual provides the location of the ISOFIX installation points and top

fastening strap, as well as other necessary information for installing the car seat in your vehicle. The

user MUST read the vehicle operation manual.

6.1.1 ISOFIX installation

• Press both sides of the ISOFIX release button (13) and extend the ISOFIX connector arms (14) to

their maximum length (fig. E.1). Repeat it on the other side.

• Grasp the car seat with both hands and insert both latches into the places of installation on the

vehicle seat (fig. E.1).

• Place the Top-Tether fastening strap (16) over the headrest so that you do not block your access to

it when installing the ISOFIX connectors.

• When you hear a "click" from each of the ISOFIX latches, push the seat of the car seat against the

backrest, exerting firm, even pressure on both sides (fig. E.1).



E.2

E.3

6.1.2 Installation of the Top-Tether

• Pull out the Top-Tether strap (16) and press the buckle release button to loosen it. The length of

the strap must allow the hook to be placed on the anchorage point at the rear of the vehicle seat or

in the trunk.

• Attach the strap anchorage hook to the vehicle anchorage point recommended in the vehicle

manual (fig. E.3). IMPORTANT: The Top-Tether (16) must not pass over the headrest of the vehicle. It

should pass under the headrest of the vehicle. If it is not possible, remove the headrest of the vehicle

(check if it is allowed according to the vehicle manual).

• Pull the fastening strap on the other end to tighten it.

•The Top-Tether is correctly tensioned when the green indicator in the buckle is visible.

• Place the child in the car seat and secure it with the internal safety harness (see section 5.2)

Andere Handbücher für JUNIOR FIX 2 i-Size

Inhaltsverzeichnis

Andere Kinderkraft Autositz Handbücher

Kinderkraft

Kinderkraft Unity Bedienungsanleitung

Kinderkraft

Kinderkraft I-CARE i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft MINK PRO i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft MINK Bedienungsanleitung

Kinderkraft

Kinderkraft I-SPARK i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft XPAND 2 i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft VADO Bedienungsanleitung

Kinderkraft

Kinderkraft XPEDITION 2 i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft JUNIOR FIX 2 i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft I-GUARD Bedienungsanleitung

Kinderkraft

Kinderkraft SAFETY FIX Bedienungsanleitung

Kinderkraft

Kinderkraft ONETO3 Bedienungsanleitung

Kinderkraft

Kinderkraft I-GROW Bedienungsanleitung

Kinderkraft

Kinderkraft XPAND 2 i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft CAR SEAT ADAPTER EVOLUTION COCOON Bedienungsanleitung

Kinderkraft

Kinderkraft XPAND 2 i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft MYWAY Bedienungsanleitung

Kinderkraft

Kinderkraft JUNIOR FIX Bedienungsanleitung

Kinderkraft

Kinderkraft Comfort Up Bedienungsanleitung

Kinderkraft

Kinderkraft JUNIOR FIX 2 i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft I-360 Bedienungsanleitung

Kinderkraft

Kinderkraft I-GUARD Bedienungsanleitung

Kinderkraft

Kinderkraft COMFORT UP i-Size Bedienungsanleitung

Kinderkraft

Kinderkraft ONETO3 Bedienungsanleitung

Beliebte Autositz Handbücher anderer Marken

Britax

Britax PARKWAY SGL Bedienungsanleitung

JANE

JANE nurse cruiser Bedienungsanleitung

Digicom

Digicom Tippy Pad Bedienungsanleitung

Giordani

Giordani orion 012 Bedienungsanleitung

BRIO

BRIO ZENTO Bedienungsanleitung

Combi

Combi Zeus Turn 8815 Series Bedienungsanleitung

Graco

Graco Car Booster Seat Bedienungsanleitung

Coccolle

Coccolle Atira Bedienungsanleitung

hifold

hifold HF01-GL Bedienungsanleitung

CYBEX

CYBEX SOLUTION X2-FIX Bedienungsanleitung

kiwy

kiwy SLF 123 Bedienungsanleitung

Safety 1st

Safety 1st Summit ISO 30 Bedienungsanleitung

Safety 1st

Safety 1st Grand 2-IN-1 Bedienungsanleitung

Graco

Graco NAUTILUS Bedienungsanleitung

Britax

Britax Multi-Tech BB0-702-00 Bedienungsanleitung

Grammer

Grammer MSG45/421 Betriebsanleitung

Nuna

Nuna REBL PLUS Bedienungsanleitung

Graco

Graco Child Restraint Bedienungsanleitung