KING KC-12HS-VS Bedienungsanleitung

INSTRUCTION MANUAL

MODEL: KC-12HS-VS

12” VARIABLE SPEED BENCH DRILL PRESS

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

FOR THIS 12” DRILL PRESS

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY

FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this product are available at our authorized King Canada service centers across Canada. Please use the 10 digit

part numbers listed in this manual for all part orders where applicable.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the

original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from

defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence

or accidents, repairs done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be

liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purchase to an

authorized King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our

authorized service centers. In cooperation with our authorized service center, King Canada will either repair or replace the product if

any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the

warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

GENERAL SAFETY INSTRUCTIONS

FOR POWER TOOLS

1. USING A DRILL PRESS VISE. When using a drill press vise, always

fasten it to the table.

2. NEVER DO “FREEHAND WORK”. Never do any work “Freehand”

(hand holding the workpiece rather than supporting it on the table)

except when you have polishing to do.

3. NEVER move the head or table while the drill press is running.

4. USE THE RECOMMENDED SPINDLE SPEED for the specific

operation and workpiece material.

5. NEVER climb on the drill press table, it could break or pull the entire

drill press down on you.

6. KEEP HANDS well away from the drill bit and all moving parts. Use

a hold-down or clamp to secure the workpiece, and use a brush, not

hands, to clear away chips and dust.

7. BE SURE THAT THE DRILL BIT IS SECURELY INSTALLED in the

chuck before operation.

8. BE SURE THE DRILL BIT has gained full operating speed before

beginning to drill.

9. ALWAYS USE a clean, properly sharpened bit. Dirty or dull bits are

unsafe and can lead to accidents.

10. USE SUITABLE WORKPIECE SUPPORT if the workpiece does

not have a flat surface.

11. DO NOT PUSH OR FORCE THE BIT into the workpiece. The drill

will perform better and more safely when working at the rate feed

for which it was designed.

12. AVOID WORKING FROM AWKWARD OR OFF BALANCE

POSITIONS. Do not overreach and keep both feet on floor.

13. KEEP GUARDS IN PLACE and in working order. If a guard must

be removed for maintenance or cleaning be sure it is properly

reinstalled before using the machine again.

14. NEVER LEAVE THE MACHINE unattended while it is running or

with the power on.

SPECIFIC SAFETY INSTRUCTIONS FOR 12” DRILL PRESS

1. KNOW YOUR TOOL

Read and understand the owners manual and labels affixed to

the tool. Learn its application and limitations as well as its specific

potential hazards.

2. GROUND THE TOOL.

This tool is equipped with an approved 3-conductor cord and a

3-prong grounding type plug to fit the proper grounding type

receptacle. The green conductor in the cord is the grounding wire.

NEVER connect the green wire to a live terminal.

3. KEEP GUARDS IN PLACE.

Keep in good working order, properly adjusted and aligned.

4. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and adjusting wrenches

are removed from tool before turning it on.

5. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents. Make sure the floor

is clean and not slippery due to wax and sawdust build-up.

6. AVOID DANGEROUS ENVIRONMENT.

Don’t use power tools in damp or wet locations or expose them to

rain. Keep work area well lit and provide adequate surrounding

work space.

7. KEEP CHILDREN AWAY.

All visitors should be kept a safe distance from work area.

8. MAKE WORKSHOP CHILD-PROOF.

-with padlocks, master switches or by removing starter keys.

9. USE PROPER SPEED.

A tool will do a better and safer job when operated at the proper

speed.

10. USE RIGHT TOOL.

Don’t force the tool or the attachment to do a job for which it was

not designed.

11. WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties or jewelry (rings,

watch) because they could get caught in moving parts. Non-slip

footwear is recommended. Wear protective hair covering to

contain long hair. Roll up long sleeves above the elbows.

12. ALWAYS WEAR SAFETY GLASSES.

Always wear safety glasses (ANSI Z87.1). Everyday eye-glasses

only have impact resistant lenses, they are NOT safety glasses.

Also use a face or dust mask if cutting operation is dusty.

13. DON’T OVERREACH.

Keep proper footing and balance at all times.

14. MAINTAIN TOOL WITH CARE.

Keep tools sharp and clean for best and safest performance.

Follow instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS.

Before servicing, when changing accessories or attachments.

16. AVOID ACCIDENTAL STARTING.

Make sure the switch is in the ‘’OFF’’ position before plugging in.

17. USE RECOMMENDED ACCESSORIES.

Consult the manual for recommended accessories. Follow the

instructions that accompany the accessories. The use of improper

accessories may cause hazards.

18. NEVER STAND ON TOOL.

Serious injury could occur if the tool tips over. Do not store

materials such that it is necessary to stand on the tool to reach

them.

19. CHECK DAMAGED PARTS.

Before further use of the tool, a guard or other parts that are

damaged should be carefully checked to ensure that they will

operate properly and perform their intended function. Check for

alignment of moving parts, breakage of parts, mounting, and any

other conditions that may affect its operation. A guard or other

parts that are damaged should be properly repaired or replaced.

20. NEVER LEAVE MACHINE RUNNING

UNATTENDED.

Turn power ‘’OFF’’. Don’t leave any tool running until it comes to

a complete stop.

WARNING

ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN

SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE MACHINE DISCONNECTED FROM THE POWER

SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!

POWER SUPPLY

WARNING: YOUR DRILL PRESS MUST BE CONNECTED TO A 120V WALL

OUTLET, WITH A MINIMUM 15-AMP. BRANCH CIRCUIT AND USE A

15-AMP TIME DELAY FUSE OR CIRCUIT BREAKER. FAILURE TO

CONNECT IN THIS WAY CAN RESULT IN INJURY FROM SHOCK OR FIRE.

GROUNDING

Your drill press must be properly grounded. Not all outlets are properly

grounded. If you are not sure if your outlet is properly grounded, have it

checked by a qualified electrician.

WARNING: IF NOT PROPERLY GROUNDED, THIS DRILL PRESS CAN

CAUSE ELECTRICAL SHOCK, PARTICULARLY WHEN USED IN DAMP

LOCATIONS. TO AVOID SHOCK OR FIRE, IF THE POWER CORD IS WORN

OR DAMAGED IN ANY WAY, HAVE IT REPLACED IMMEDIATELY.

If this drill press should malfunction or breakdown, grounding provides a path

of least resistance for electric current, to reduce the risk of electric shock. This

drill press is equipped with a cord having an equipment-grounding conductor

and grounding plug. The plug must be plugged into an appropriate outlet that

is properly installed and grounded in accordance with all local codes and

ordinances.

WARNING: TO MAINTAIN PROPER GROUNDING, DO NOT REMOVE OR

ALTER THE GROUNDING PRONG IN ANY MANNER.

120V OPERATION

As received from the factory, your drill press is ready to run for 110V-120V

operation. This machine is intended for use on a circuit that has an outlet and

a plug which looks like the one illustrated in Fig.1.

WARNING: DO NOT USE A TWO-PRONG ADAPTER(S) FOR THEY ARE

NOT IN ACCORDANCE WITH LOCAL CODES AND ORDINANCES. NEVER

USE IN CANADA.

EXTENSION CORDS

The use of any extension cord will cause some loss of power. If you do not

have a choice, use the table in Fig.2 to determine the minimum wire size

(A.W.G-American Wire Gauge) extension cord needed. Use only 3-wire

extension cords which have 3-prong grounding type plugs and 3-hole

receptacles which accept the tool’s plug.

For circuits that are further away from the electrical circuit box, the wire size must

be increased proportionately in order to deliver ample voltage to the drill press

motor. Refer to Fig.2 for wire length and size.

ON/OFF SWITCH WITH REMOVABLE SAFETY KEY

The On/Off switch (A) Fig.3 comes with a removable safety key (B). When the

safety key is removed from the switch and placed in a safe location,

unauthorized persons or children can’t turn the switch to the On position. It is

recommended to always remove the safety key from the switch whenever the

Drill Press is not in use.

To turn the Drill Press On, lift the switch (A) Fig.3. To turn the Drill Press Off

press down on the switch.

Figure 1

Figure 2

PROPERLY GROUNDED OUTLET

CURRENT CARRYING

PRONGS

GROUNDING

PRONG

Figure 3

ELECTRICAL INFORMATION

Tool’s

Amperage

Rating

3-6

6-8

8-10

10-12

12-16

Cord Size in A.W.G.

Cord Length in Feet

25 50 100 150

18 16 16 14

18 16 14 12

14 12 --

FIGURE 4

FIGURE 5

GETTING TO KNOW YOUR DRILL PRESS

1. Base

2. Column

3. Table locking lock handle

4. Tilting table

5. Tilting table extension

6. 5/8” chuck

7. Worklight switch

8. Dual laser switch

9. On/Off switch

10. Variable speed digital readout

11. Pulley cover

12. Feed handle (1 of 3)

13. Table raising/lowering handle

14. Mechanical variable speed

adjusting lever

15. Depth stop

SPECIFICATIONS

MODEL KC-12HS-VS

Capacity 5/8”

Chuck size 5/8”

Swing 12”

Max. distance chuck to column 6”

Max. distance chuck to table 13”

Stroke 3”

Table size with extension 16-1/4” x 9-1/2”

Spindle taper MT#2

Variable speeds 580 -3200 RPM

Table T-slots 9/16”

Motor/Voltage 5 Amp. @ 120V, 60 Hz, 1 phase

Ass. dimensions (LxWxH)/weight 19-1/2” x 21” x 37-1/2” / 82 lbs

Pkg dimensions (LxWxH)/weight 29-1/4” x 19-3/4” x 11-1/2” / 87 lbs

FIGURE 6

ASSEMBLY

FIGURE 7

FIGURE 8

BASE, COLUMN & TABLE ASSEMBLY

1) Position the base (A) Fig.6 on the floor. Remove the protective

covering and discard.

2) Remove protective bag from the column, column support and table

support assembly (B) and discard. Place the column assembly on the

base, align the holes in the column support with the holes in the base.

3) Locate four long hex. bolts from the parts bag.

4) Install a hex. bolt (C) Fig.6 in each hole through the column support

and the base and tighten with a wrench.

Note: It is recommended to securely fasten the drill press base (A) Fig.6

to a wooden base or floor. This would prevent the drill press from

possibly tipping over, walking during operation.

5) Locate the crank handle (A) Fig.7 and install it on the worm gear shaft

on the side of the table support (B). Tighten the set screw (C) on the

flat section of the worm gear shaft.

6) Install the table support lock handle (D) Fig.7 to the table support as

shown.

7) Install the table lock handle (A) Fig.8 to the table support as shown.

Do not tighten.

8) Slide the table (B) Fig.8 into the opening of the table support. This

table comes with a convenient table extension (C) which can be

pulled out to support larger workpieces. Choose which side you

would like the table extension to face (right or left side), then install

and tighten 2 lock knobs (D). Tighten table lock handle (A).

ASSEMBLY

FIGURE 9

FIGURE 10

FIGURE 11

INSTALLING THE HEAD

Warning! The drill press head is very heavy, it is not recommended to

attempt installation of the head by yourself, obtain help.

1) Carefully lift the head (A) Fig.9 above the column (B) and slide it down

on the column as far as it will go. Align the head with the table and the

base.

2) Using a 5 mm hex. key, tighten both head set screws (C) Fig.9 on the

right side of the head.

INSTALLING DOWNFEED HANDLES

1) Screw the 3 downfeed handles (A) Fig.10 to the feed hub (B) as

shown.

INSTALLING VARIABLE SPEED ADJUSTING HANDLE

1) Screw the variable speed handle (C) Fig.10 to the variable speed hub

(D) as shown.

INSTALLING CHUCK & ARBOR

1) Before attempting to install chuck on the drill press arbor, and

installing arbor in spindle, it is extremely important to clean all grease

and or dirt particles from the chuck opening and the arbor. Make sure

there are no foreign particles sticking to the surfaces. The slightest

piece of dirt on the arbor nose or the chuck will prevent the chuck from

seating properly. This will cause the drill to “wobble”.

2) Locate the 5/8” chuck (A) Fig.11 and arbor (B). Insert the arbor into

the chuck opening.

3) Push the chuck and arbor assembly up into the drill spindle (C) as far

as they will go. Turn chuck and arbor assembly until it completely

enters the spindle.

4) Turn the chuck sleeve clockwise, or use the supplied chuck key, and

open the chuck jaws completely.

5) Lightly tap the nose of the chuck with a piece of wood to insure the

proper seating of the chuck on the arbor and arbor in the spindle.

REMOVING THE CHUCK & ARBOR

1) Lower the quill using the feed handles. Align key holes in spindle and

quill (A) Fig.12 as shown by rotating the chuck (B) by hand.

2) Insert drift key (C) into key holes in the quill.

3) Tap drift key lightly until the chuck and arbor fall out of the spindle.

NOTE: Place one hand below the chuck to catch it when it falls out.

FIGURE 12

ASSEMBLY & ADJUSTMENTS

FIGURE 13

FIGURE 14

FIGURE 15

INSTALLING A DRILL BIT IN THE 5/8” CHUCK

1) Insert the chuck key (A) Fig.13 into the chuck (B) as shown, turn

chuck key counterclockwise to open the chuck jaws.

2) Insert a drill bit (C).

3) Tighten the chuck key clockwise to secure the drill bit in the chuck.

Note: This drill press comes with a convenient chuck key holder (D)

Fig.13. Reposition chuck key in chuck key holder after adjustment to

avoid misplacing the chuck key.

ADJUSTMENTS

RAISING/TILTING TABLE

Raising Table-

1) Loosen table lock handle (A) Fig.14.

2) Turn the table height adjustment handle (B) until the table is at the

desired height.

3) Retighten table lock handle (A).

Tilting Table-

1) Loosen table angle setting hex bolt (A) Fig.15 using a 17mm wrench.

2) Tilt the table (B) to the desired position. Use the angle scale (C) as a

general guide for the desired angle.

3) Retighten table angle setting hex bolt (A).

Note: When working with taller workpieces, swing the table 180° out of

the way and use the base as a table.

SQUARING TABLE WITH DRILL BIT

1) With a drill bit installed in the 5/8” chuck, raise table until it is a few

inches away from the tip of the drill bit. Lock the table.

2) Position a square (A) Fig.16 on the table, and up against the drill bit

(B) as shown in Fig.16.

3) Check to make sure the table is perfectly square with the drill bit. If an

adjustment is needed, loosen table angle setting hex bolt (A) Fig.15

using a 17mm wrench.

4) Slightly tilt the table until it is square with the drill bit, once adjustment

is done, retighten table angle setting hex bolt (A) Fig.15 using a

17mm wrench.

FIGURE 16

ADJUSTMENTS & OPERATION

FIGURE 17

FIGURE 18

FIGURE 19

USING AND ADJUSTING DUAL LASER GUIDES

Warning! Do not look into the direct or reflected laser beam; can cause

eye injury up to 50 feet (15m) away. Class 2 lasers are considered safe

for accidental eye exposure. Do not look or stare into laser beam. This

is not a toy.

1) The dual laser guide system can be turned On/Off using the front

mounted laser switch (A) Fig.17.

2) Position your workpiece on the table and clamp it. Lower the drill bit

just above the workpiece. Turn on dual laser guide, The dual laser

guide laser beams must cross where the drill bit touches the

workpiece. If the dual laser guide laser beams is not properly aligned,

an adjustment can be made:

- Loosen set screw (A) Fig.18 using a hex. key. Turn laser tip (B) until

the laser beam is correctly positioned. Retighten set screw. Repeat

this step for the other laser guide on opposite side if needed.

USING THE DEPTH STOP

The depth stop mechanism Fig.19 allows repetitive drilling to an equal

depth, to adjust the depth stop mechanism:

1) Lower the downfeed handles until your cutting tool reaches the

desired drilling depth.

2) At the same time, push in the spring button (A) Fig.19 of the depth

stop setting nut (B) and move it against the head casting (C). The

depth stop scale (D) can also be used as a guide for setting the depth

adjustment.

3) Release the downfeed handles and check your adjustment.

CHANGING SPEED

This drill press has a variable spindle speed range from 580 to 3200

RPM. The spindle speed setting is conveniently displayed on the digital

readout on the head of the drill press. To change the spindle speed:

WARNING! Always adjust the spindle speed while the drill press is

running to avoid damaging the speed adjustment mechanism.

1) Turn the drill press on.

2) The spindle speed is controlled by the speed adjusting lever (A)

Fig.20 located on the left side of the drill press head.

3) Turn the lever counterclockwise to increase the spindle speed.

4) Turn the lever clockwise to decrease the spindle speed.

5) Refer to the digital readout (B) Fig.20 on the front of the drill press

head to set the desired speed.

FIGURE 20

ADJUSTMENTS & OPERATION

FIGURE 21

FIGURE 22

ADJUSTING PLAY IN QUILL/SPINDLE

If a small or excessive play in the quill/spindle is noticed, an adjustment

can be made. Using the downfeed handles, lower the quill/spindle (C)

Fig.21 as far as it will go. Check to see if there is excessive play

(side-to-side movement) in the quill/spindle. If there is play, adjust as

follows:

1) Place a flat head screwdriver on the screw (B) Fig.21, while preventing

the screw from turning, loosen large hex. nut (A).

2) Slightly tighten the flat head screw (B) until the play is eliminated.

Note that a small amount of play is normal.

3) Make sure the up and down movement of the quill/spindle is

unobstructed.

4) Place a flat head screwdriver on the screw (B) Fig.21, while

preventing the screw from turning, retighten large hex. nut (A).

OPERATION

TURNING DRILL PRESS ON/OFF

The On/Off switch (A) Fig.22 comes with a removable safety key (B).

When the safety key is removed from the switch and placed in a safe

location, unauthorized persons or children can’t turn the switch to the On

position. It is recommended to always remove the safety key from the

switch whenever the Drill Press is not in use.

To turn the Drill Press On, lift the switch (A) Fig.22. To turn the Drill Press

Off press down on the switch.

ACTIVATING THE LASER GUIDE SYSTEM

In order to activate the laser guide system, first the Drill Press power

cord must be connected to a power source, or the lasers will not turn on.

The laser switch (C) Fig.22 turns the laser guide system on/off.

TURNING WORKLIGHT ON/OFF

In order to activate the incorporated worklight, first the Drill Press power cord must be connected to a power source, or the worklight will not turn

on. The worklight switch (D) Fig.22 turns worklight on/off.

WARNING! To reduce the risk of fire, do not use light bulb greater than 40 watts.

OPERATIONAL GUIDELINE

FEEDING

Pull down the feed handles with only enough effort to allow the drill to cut. Feeding too slowly might cause the drill to burn...feeding too rapidly

might stop the motor...cause the belt or drill to slip... tear the workpiece loose or break the drill bit.

HOLE LOCATION

Make an indentation in the workpiece where you want the to drill a hole using a centre punch or a sharp nail. Before turning the switch ON, bring

the drill bit down to the workpiece, lining it up with the hole location.

POSITIONING THE TABLE AND WORKPIECE

Lock the table to the column in a position so that the tip of the drill is just a little above the top of the workpiece. Always place a piece of

back-up material (wood, plywood) on the table underneath the workpiece. This will prevent splintering or making a heavy burr on the underside

of the workpiece as the drill breaks through. To keep the back-up material from spinning out of control, it must come in contact with the left side

of the column.

WARNING! To prevent the workpiece or the back-up material from being torn from your hand while drilling, position them against the left side of

the column. If the workpiece or the back-up material are not long enough to reach the column, clamp them to the table. Failure to do this could

result in personal injury.

Inhaltsverzeichnis

Andere KING Elektrowerkzeuge Handbücher

KING

KING KC-30HS-VS Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung