KING KC-30HS-VS Bedienungsanleitung

INSTRUCTI N MANUAL

MODEL: KC-30HS-VS

15” VARIABLE SPEED

INDUSTRIAL DRILL PRESS

Line Interruption

09/2017

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

F R THIS 15” DRILL PRESS

KING CANADA T LS

FFERS A 2-YEAR LIMITED WARRANTY

F R N N-C MMERCIAL USE.

PR F F PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this product are available at our authorized King Canada service centers across Canada.

LIMITED T L WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the

original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from

defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence or

accidents, repairs done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be liable

for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an authorized

King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our authorized

service centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if any part or

parts covered under this warranty which examination proves to be defective in workmanship or material during the warranty period.

N TE T USER

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

KING CANADA INC. D RVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

GENERAL SAFETY INSTRUCTIONS

FOR POWER TOOLS

1. USING A DRILL PRESS VISE. When using a drill press vise, always

fasten it to the table.

2. NEVER D “FREEHAND W RK”. Never do any work “Freehand”

(hand holding the workpiece rather than supporting it on the table)

except when you have polishing to do.

3. NEVER move the head or table while the drill press is running.

4. USE THE REC MMENDED SPINDLE SPEED for the specific

operation and workpiece material.

5. NEVER climb on the drill press table, it could break or pull the entire

drill press down on you.

6. KEEP HANDS well away from the drill bit and all movingparts. Use

a hold-down or clamp to secure the workpiece, and use a brush, not

hands, to clear away chips and dust.

7. BE SURE THAT THE DRILL BIT IS SECURELY INSTALLED in the

chuck before operation.

8. BE SURE THE DRILL BIT has gained full operating speed before

beginning to drill.

9. ALWAYS USE a clean, properly sharpened bit. Dirty or dull bits are

unsafe and can lead to accidents.

10. USE SUITABLE W RKPIECE SUPP RT if the workpiece does

not have a flat surface.

11. D N T PUSH R F RCE THE BIT into the workpiece. The drill

will perform better and more safely when working at the rate feed

for which it was designed.

12. AV ID W RKING FR M AWKWARD R FF BALANCE

P SITI NS. Do not overreach and keep both feet on floor.

13. KEEP GUARDS IN PLACE and in working order. If a guard must

be removed for maintenance or cleaning be sure it is properly

reinstalled before using the machine again.

14. NEVER LEAVE THE MACHINE unattended while it is running or

with the power on.

SPECIFIC SAFETY INSTRUCTIONS FOR 15” DRILL PRESS

1. KN W Y UR T L

Read and understand the owners manual and labels affixed to the

tool. Learn its application and limitations as well as its specific

potential hazards.

2. GR UND THE T L.

This tool is equipped with an approved 3-conductor cord and a

3-prong grounding type plug to fit the proper grounding type

receptacle. The green conductor in the cord is the grounding wire.

NEVER connect the green wire to a live terminal.

3. KEEP GUARDS IN PLACE.

Keep in good working order, properly adjusted and aligned.

4. REM VE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and adjusting wrenches

are removed from tool before turning it on.

5. KEEP W RK AREA CLEAN.

Cluttered areas and benches invite accidents. Make sure the floor

is clean and not slippery due to wax and sawdust build-up.

6. AV ID DANGER US ENVIR NMENT.

Don’t use power tools in damp or wet locations or expose them to

rain. Keep work area well lit and provide adequate surrounding

work space.

7. KEEP CHILDREN AWAY.

All visitors should be kept a safe distance from work area.

8. MAKE W RKSH P CHILD-PR F.

-with padlocks, master switches or by removing starter keys.

9. USE PR PER SPEED.

A tool will do a better and safer job when operated at the proper

speed.

10. USE RIGHT T L.

Don’t force the tool or the attachment to do a job for which it was

not designed.

11. WEAR PR PER APPAREL.

Do not wear loose clothing, gloves, neckties or jewelry (rings,

watch) because they could get caught in moving parts. Non-slip

footwear is recommended. Wear protective hair covering to

contain long hair. Roll up long sleeves above the elbows.

12. ALWAYS WEAR SAFETY GLASSES.

Always wear safety glasses (ANSI Z87.1). Everyday eye-glasses

only have impact resistant lenses, thet are N T safety glasses.

Also use a face or dust mask if cutting operation is dusty.

13. D N’T VERREACH.

Keep proper footing and balance at all times.

14. MAINTAIN T L WITH CARE.

Keep tools sharp and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

15. DISC NNECT T LS.

Before servicing, when changing accessories or attachments.

16. AV ID ACCIDENTAL STARTING.

Make sure the swich is in the ‘’OFF’’ position before plugging in.

17. USE REC MMENDED ACCESS RIES.

Consult the manual for recommended accessories. Follow the

instructions that accompany the accessories. The use of improper

accessories may cause hazards.

18. NEVER STAND N T L.

Serious injury could occur if the tool tips over. Do not store

materials such that it is necessary to stand on the tool to reach

them.

19. CHECK DAMAGED PARTS.

Before further use of the tool, a guard or other parts that are

damaged should be carefully checked to ensure that they will

operate properly and perform their intended function. Check for

alignment of moving parts, breakage of parts, mounting, and any

other conditions that may affect its operation. A guard or other parts

that are da -maged should be properly repaired or replaced.

20. NEVER LEAVE MACHINE RUNNING

UNATTENDED.

Turn power ‘’OFF’’. Don’t leave any tool running until it comes to a

complete stop.

WARNING

ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS

IN URY! ALL AD USTMENTS OR REPAIRS MUST BE DONE WITH THE MACHINE DISCONNECTED FROM THE POWER SOURCE.

FAILURE TO COMPLY MAY RESULT IN SERIOUS IN URY!

P WER SUPPLY

WARNING: YOUR DRILL PRESS MUST BE CONNECTED TO A 115V

WALL OUTLET, WITH A MINIMUM 15-AMP. BRANCH CIRCUIT AND USE

A 15-AMP TIME DELAY FUSE OR CIRCUIT BREAKER. FAILURE TO

CONNECT IN THIS WAY CAN RESULT IN IN URY FROM SHOCK OR

FIRE.

GR UNDING

Your drill press must be properly grounded. Not all outlets are properly

grounded. If you are not sure if your outlet is properly grounded, have it

checked by a qualified electrician.

WARNING: IF NOT PROPERLY GROUNDED, THIS DRILL PRESS CAN

CAUSE ELECTRICAL SHOCK, PARTICULARLY WHEN USED IN DAMP

LOCATIONS. TO AVOID SHOCK OR FIRE, IF THE POWER CORD IS

WORN OR DAMAGED IN ANY WAY, HAVE IT REPLACED IMMEDIATELY.

If this drill press should malfunction or breakdown, grounding provides a

path of least resistance for electric current, to reduce the risk of electric

shock. This drill press is equipped with a cord having an

equipment-grounding conductor and grounding plug. The plug must be

plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

WARNING: TO MAINTAIN PROPER GROUNDING, DO NOT REMOVE OR

ALTER THE GROUNDING PRONG IN ANY MANNER.

115V PERATI N

As received from the factory, your drill press is ready to run for 115V

operation. This machine is intended for use on a circuit that has an outlet

and a plug which looks like the one illustrated in Fig.1.

WARNING: DO NOT USE A TWO-PRONG ADAPTER(S) FOR THEY ARE

NOT IN ACCORDANCE WITH LOCAL CODES AND ORDINANCES.

NEVER USE IN CANADA.

EXTENSI N C RDS

The use of any extension cord will cause some loss of power. If you do not

have a choice, use the table in Fig.2 to determine the minimum

wire size (A.W.G-American Wire Gauge) extension cord

needed. Use only 3-wire extension cords which have 3-prong

grounding type plugs and 3-hole receptacles which accept the

tool’s plug.

For circuits that are further away from the electrical circuit box,

the wire size must be increased proportionately in order to

deliver ample voltage to the drill press motor. Refer to Fig.2

for wire length and size.

Figure 1

Figure 2

PR PERLY GR UNDED UTLET

CURRENT CARRYING

PR NGS

GR UNDING

PR NG

Figure 3

TURNING THE DRILLPRESS N/ FF

This Drill Press comes with a 2 step activation safety switch, refer

to Fig.3, which starts and stops the machine. To turn the Drill Press

on:

1. Push up on the emergency stop button (A) Fig.3 and lift the switch

cover (B) upwards as shown.

2. Press the green On button (C) to start the Drill Press.

3. To stop the Drill Press, you can either press the red Off button (D)

or lower the switch cover and push the large emergency stop

button (E).

ELECTRICAL INFORMATION

Tool’s

Amperage

Rating

3-6

6-8

8-10

10-12

12-16

Cord Size in A.W.G.

Cord Length in Feet

25 50 100 150

18 16 16 14

18 16 14 12

14 12 - -

FIGURE 4

FIGURE 5

GETTING TO KNOW YOUR DRILL PRESS

1. Variable speed digital readout.

2. Speed adjusting handwheel.

3. 2 step activation safety switch.

4. Safety guard.

5. 5/8” chuck.

6. Table.

7. Base.

8. Head locking handle.

9. Depth stop rod.

10. Feed handle (1 of 3).

11. Column and rack.

12. Table raising/lowering handle.

13. Safety guard lock knob.

14. Limit switch.

15. Safety guard height adjusting lock

knob.

16. Spring return.

SPECIFICATIONS

MODEL KC-30HS-VS

Capacity 5/8”

Chuck size 5/8”

Swing 15”

Max. distance chuck to column 7-1/2”

Max. distance chuck to table 27-1/2”

Stroke 6”

Table size 18” x 14”

Spindle taper T#3

Variable speeds 400 - 5,000 RPM

Table T-slots 9/16”

Quill diameter 2-1/4”

Column diameter 3”

Motor/Voltage 14 Amp. @ 115V, 7 Amp. @ 230V

Pre-wired 115V

Ass. dimensions (LxWxH)/weight 18” x 28” x 71-1/2” / 310 lbs

Pkg dimensions (LxWxH)/weight 22” x 32” x 70” / 375 lbs

ASSEMBLY

This drill press comes partially assembled and requires minimal assembly

and set up before being put into use.

INSTALLING TABLE HEIGHT ADJUSTMENT HANDLE

1. Align the set screw (A) Fig.6 in the table height adjustment handle (B)

with the flat portion of the handle shaft.

2. Slide the table height adjustment handle (B) onto the shaft and

tighten the set screw (A) using a 4mm hex. key.

RAISING THE HEAD

This drill press is shipped with the head lowered. To operate this drill

press correctly, the head must be raised.

1. Loosen the head locking handle (A) Fig.7 and place a block of wood

(B) on the table and under the bottom of the head as shown.

2. Loosen table lock handle (C), then turn table height adjustment handle

(D) to raise the head.

3. Once the head is positioned at a comfortable height, retighten head

locking handle (A) and table lock handle (C).

4. Loosen and move up the column collar (E) until it comes in contact

with the bottom of the head, secure the column collar up against the

head by tightening the large hex. bolt and hex. nut.

INSTALLING THE 5/8” CHUCK

1. Slide the 5/8” chuck (A) Fig.8 onto the tapered end of the spindle (B).

2. Place a piece of wood on the table and using the down-feed handles,

lower the quill assembly against the piece of wood on the table to

secure the chuck on the spindle.

FIGURE 6

ASSEMBLY

FIGURE 7

FIGURE 8

AD USTMENTS AND OPERATION

RAISING R L WERING W RK TABLE

1. Loosen table lock handle (A) Fig.9.

2. Turn the table height adjustment handle (B) until the table is at the

desired height.

3. Retighten table lock handle (A).

ADJUSTING ANGLE F W RK TABLE

1. Loosen table lock handle (A) Fig.9.

2. Swing the table (C) to the desired position.

3. Retighten table lock handle (A).

Note: When working with taller workpieces, swing the table 180° out of

the way and use the base as a table.

USING THE DEPTH ST P

The depth stop mechanism Fig.10 allows repetitive drilling to an equal

depth, to adjust the depth stop mechanism:

1. Lower the downfeed handles until your cutting tool reaches the desired

drilling depth.

2. At the same time, position the bottom hex. nut (A) Fig.10 against the

head casting (B).

3. Release the downfeed handles and check your adjustment.

4. If properly set, tighten hex. nut (C) against hex. nut (A) to secure the

adjustment. Depth stop mechanism is now set and you can now do

repetitive drilling at equal depth.

CHANGING SPEED

This drill press has a variable spindle speed range of 400 to 5000 RPM,

the speed setting is conveniently displayed on the digital readout on the

head of the drill press. To set the spindle speed:

WARNING! Always adjust the spindle speed while the drill press is

running to avoid damaging the speed adjustment mechanism.

1. Turn the drill press on.

2. The spindle speed is controled by the speed adjusting handwheel (A)

Fig.11 located on the left side of the drill press head.

3. Turn the handwheel clockwise to increase the spindle speed.

4. Turn the handwheel counterclockwise to decrease the spindle speed.

5. Refer to the digital readout (B) on the front of the drill press head to

set the desired speed.

Refer to the reference chart (Fig.12) for recommended speed selection,

based on the drill bit size and workpiece material.

FIGURE 9

FIGURE 10

FIGURE 11

AD USTMENTS & OPERATION

INSTALLING A DRILL BIT IN THE 5/8” CHUCK

1. Swing the chuck safety guard out of the way.

2. Insert the chuck key (A) Fig.13 into the chuck (B) as shown, turn chuck

key counterclockwise to open the chuck jaws.

3. Insert a drill bit (C).

4. Tighten the chuck key to secure the drill bit in the chuck.

USING AND AJUSTING THE LIMIT SWITCH PR TECTED

SAFETY GUARD

The limit switch safety guard (A) Fig.14 is intended to protect the operator

during drilling operations. If the safety guard is not positioned in its closed

position (in front of the drill chuck as shown), the safety guard limit switch

will prevent the drill press from starting. Close the safety guard and then

press the green On button to start. If the safety guard is opened during a

drilling operation the drill press will shut off automatically, the safety guard

will need to be closed and the green On button will need to be pressed

to restart drill press.

To adjust the safety guard:

1. The height of the safety guard (A) Fig.14 needs to be adjusted so it

covers the cutting tool. To adjust the height of the safety guard

assembly loosen lock handle (D), move the safety guard bar (B) up or

down until the safety guard is positioned correctly. Retighten lock

handle (D).

2. To lock and prevent the bar (B) and safety guard (A) from opening

during an operation, tighten lock knob (C).

3. Always make sure the hex. nut (E) is tight, to prevent the safety guard

from pivoting at this point. The bar (B) and safety guard (A) must move

together.

It is recommended to test the limit switch safety guard before any drilling

operation. Turn drill press on and open the safety guard, the drill press

MUST shut off. If it doesn’t, the safety guard limit switch needs to be

replaced or reinstalled correctly.

FIGURE 13

FIGURE 14

REFERENCE CHART F R SPINDLE SPEED SELECTI N - BASED N BIT SIZE/W RKPIECE MATERIAL

CAST STEEL

1900 - 2445

1220 - 1275

765 - 815

610

480-490

380-405

350

300-305

TOOL STEEL

2865-3665

1835-1910

1145-1220

915-955

715-735

570-610

520-525

440-460

CAST IRON

3820-4890

2445-2545

1530-1630

1220-1275

955-980

765-815

700

560-610

MILD STEEL

4775-6110

3055-3185

1910-2035

1530-1590

1195-1220

955-1020

870

735-765

ALUM. & COPPER

9550-12225

6110-6365

3820-4075

3055-3180

2390-2445

1910-2035

1740-1745

1470-1530

The information in the above chart is supplied as a general guide only. For best results always follow the speed recommendations supplied

with the drill bits being used.

REVOLUTIONS PER MINUTE (RPM)

WORKPIECE MATERIAL

BIT SIZE (DIAMETER)

1-16” (2 mm)

1/8" (3 mm)

3/16" (5 mm)

1/4" (6 mm)

5/16" (8 mm)

3/8" (10 mm)

7/16" (11 mm)

1/2" (13 mm)

FIGURE 12

MAINTENANCE

WARNING! For your own safety, turn the switch “OFF” and remove the

plug from the power source before maintaining or lubricating your drill

press.

• Keep the Drill Press clean and free of dust and debris. Painted surfaces

can be wiped with a damp rag.

• Periodically lubricate all sliding or moving parts including the column (A)

Fig.15, rack (B) and the quill (C) (use any all purpose grease, available

at any hardware store).

• Bearings in the quill and the V-belt pulleys are sealed and permanently

lubricated – no further lubrication is required.

• Frequently blow out any dust that may accumulate inside the motor. After operation, remove chips or dirt on the machine and apply a coat of

furniture-type paste wax to the table and the column, this will help keep the surfaces clean and free of rust.

PR BLEM

Drill bit burns.

Wood splinters on un-

derside of workpiece.

Workpiece torn loose

from hand.

Drill bit binds in

workpiece.

Excessive drill bit

wobbling.

Quill returns too fast or

too slow.

Chuck will not stay at-

tached to the spindle. It

falls off when trying to

install it.

PR BABLE CAUSE

1. Incorrect speed.

2. Chips not comming out of hole.

3. Dull drill bit.

4. Feeding too slow.

5. Not lubricated.

1. No “Back-up material” under the

workpiece.

1. Not supported or clamped properly.

1. Workpiece is pinching the drill bit or there

is an excessive feeding pressure.

1. Bent drill bit.

2. Worn spindle bearings.

3. Drill bit is not properly installed in the

chuck.

4. Chuck not properly installed.

1. Spring has improper tension.

1. Dirt, grease or oil on the tapered inside

surface of the chuck or on the spindle

tapered surface.

S LUTI N

1. Change the speed.

2. Retract the drill bit frequently to clear the chips.

3. Resharpen the drill bit.

4. Feeding too fast...allow the drill bit to cut.

5. Lubricate the drill bit with cutting or motor oil.

1. Support the workpiece or clamp it.

1. Support the workpiece or clamp it. Reduce feeding

pressure.

1. Use a straight drill bit.

2. Replace the bearings.

3. Install drill bit properly.

4. Install chuck properly.

1. Adjust the spring tension.

1. Using a household detergent, clean the tapered surfaces

of the chuck and the spindle to remove the dirt, grease

and oil.

FIGURE 15

Inhaltsverzeichnis

Andere KING Elektrowerkzeuge Handbücher

KING

KING KC-12HS-VS Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch