Kipor Sinemaster IG2600h Bedienungsanleitung

SINEMASTER

DIGITAL INVERTER GENERATOR

IG2600

IG2600h

WUXI KIPOR POWER CO., LTD.

12. SKETCH MAP

IG2600h

IG2600h movement state IG2600h placed state

PREFACE

Thank you for purchasing our generators.

This manual covers operation and maintenance of the IG2600, IG2600h

generator.

All information in this publication is based on the latest product information

available at the time of approval for printing.

We reserve the right to make changes at any time without notice and without

incurring any obligation.

No part of this publication may be reproduced without written permission.

This manual should be considered a permanent part of the generator and should

remain with it if it is resold.

Pay special attention to statements preceded by the following words;

Failure to properly follow these precautions can result in

property damage, serious injury or DEATH!

Read all labels and the owner's manual before operating

this generator.

Operate only in well ventilated areas. Exhaust gas

contains poisonous carbon monoxide, and can be deadly.

Always stop engine before refueling. Wait 5 minutes

before restarting.

Check for spilled fuel or leaks. Clean and/or repair before

use.

Keep any sources of ignition away from fuel tank, at all

times.

Indicates a strong possibility of severe personal injury or

death if instructions are not followed.

Indicates a possibility of personal injury or equipment

damage if instructions are not followed.

NOTE: Gives helpful information.

If a problem should arise, or if you have any questions about the generator,

consult an authorized dealer.

Our generators are designed to give safe and dependable

service if operated according to instructions. Read and

understand the Owner's Manual before operating the gen-

erator. Failure to do so could result in personal injury or

equipment damage.

The illustration may vary according to the type.

WARNING

CAUTION

WARNING

11. SPECIFICATIONS

DC output

DC voltage

Electric circuit breaker

No. of Phase

12V-8.3A

Available

Single phase

Model IG2600/IG2600h

Rated frequency (Hz)

Rated voltage (V)

Rated current (A)

Rated speed (rpm)

Rated output (kVA)

Max output (kVA)

230

3600

2.3

2.6

240

9.6

Engine

Model Type KG171

Type

Displacement (Bore Stroke)

Compression ratio

Rated power (kW)

Rated rotation speed (rpm)

Ignition system

Spark plug

Starting system

Fuel

Fuel consumption (g /kW.h)

Lube oil

Single cylinder, 4 stroke, vertical, air-cooled, OHV, gasoline engine

171ml (66 55mm)

8.5:1

3.5/3600

3600

T. C. I

R6-388

Recoil starter

Automotive unleaded gasoline

450

SAE 10W30 (above CC grade)

Fuel tank capacity (L)

Continuous running time (hr) (at rated output)

Noise level(zero load~ full load) [dB(A)/7m]

Overall dimension (L W H) [mm(in)]

4.8

2.5

58-63 *

Dry weight [kg(lbs)]

IG2600: 26 (57.2) IG2600h: 27.5 (60.5)

IG2600: 564 317 453(22.20 12.48 17.83)

IG2600h: 590 330 480 (23.23 12.99 18.90)

120

19.5

CONTENTS

1. Safety Instructions

2. Safety Label Locations

3. Component Indentificaction

4. Pre-operation Check

5. Starting the Engine

High altitude operation

6. Generator Use

7. Stopping the Engine

8. Maintenance

9. Transporting/Storage

10. Troubleshooting

11. Specifications

12. Sketch Map

*: The declared values shall consider uncertainties due to production variation and

measurement procedures.

Is the overload

indicator light ON?

Appliance does not operate:

Is the output indicator light ON?

YES

Take the generator to an

authorized dealer.

Take the generator to an

authorized dealer.

Check the electrical appli-

ance or equipment for any

defects.

Replace the electrical

appliance or equipment

Take the electrical appli-

ance or equipment to an

electrical shop for repair

Push the reset button.

YES

No electricity at the DC receptacle:

Is DC circuit breaker tripped?

Take the generator to an

authorized dealer.

1. SAFETY INSTRUCTIONS

WARNING

Exhaust gas contains poisonous carbon monoxide.

Never run the generator in an enclosed area.

The muffler becomes very hot during operation and

remains hot for a while after stopping the engine.

Be careful not to touch the muffler while it is hot.

Let the engine cool before storing the generator indoors.

The engine exhaust system will be heated during op-

eration and remain hot immediately after stopping the

engine.

To prevent scalding, pay attention to the warning marks

attached to the generator.

Our generators are designed to give safe anddepend-

able service if operated according to instructions.

Read and understand the Owner's Manual before op-

erating the generator. Failure to do so could result in

personal injury or equipment damage.

Be sure to provide adequate ventilation.

When installed in ventilated protection are to be

observed.

To ensure safe operation--

WARNING

Gasoline is extremely flammable and explosive under

certain conditions. Refuel in a well ventilated area with

the engine stopped.

Keep away from cigarette, smoke and sparks when re-

fueling the generator. Always refuel in a well-ventilated

location.

Wipe up spilled gasoline at once.

Connections for standby power to a building's electrical

system must be made by a qualified electrician and must

comply with all applicable laws and electrical codes. Im-

proper connections can allow electrical current from the

generator to back feed into the utility lines. Such back

feed may electrocute utility company workers or others

who contact the lines during a power outage, and when

utility power is restored, the generator may explode,burn

or cause fires in the building's electrical system.

Always make a pre-operation inspection before you

start the engine. You may prevent an accident or

equipment damage.

Place the generator at least 1m(3ft) away from build-

ings or other equipment during operation.

Operate the generator on a level surface.

If the generator is tiled, fuel spillage may result.

Know how to stop the generator quickly and understand

operation of all the controls.Never permit anyone to op-

erate the generator without proper instructions.

Keep children and pets away from the generator when

it is in operation.

Keep away from rotating parts while the generator is

running.

The generator is a potential source of electrical shocks

when misused; do not operate with wet hands.

Do not operate the generator in rain or snow and do not

let it get wet.

10.TROUBLESHOOTING

When the engine will not start:

Is there fuel in the tank?

Is the engine switch on?

YES

Is there enough oil in the engine?

Is there a spark from

the spark plug?

NO Refill the fuel tank.

Turn the engine switch on.

Add the recommended oil.

Still no

spark

Replace the

spark plug.

Take the generator to an

authorized dealer.

WARNING

If the engine still does not

start, take the generator to

an authorized dealer.

Be sure there is no spilled

fuel around the spark pulg.

Spilled fuel may ignite.

To check:

1)Remove the spark plug cap and clean

any dirt from around the spark plug.

2)Remove the spark plug and install the

spark plug in the plug cap.

3)Set the plug side electrode on the cylin-

der head to ground.

4)Pull the recoil starter, sparks should jump

across the gap.

Oil level

Choke lever

Engine switch

Model

Hot caution

Drain Screw

Starter Grip

2. SAFETY LABEL LOCATIONS

These lables warn you of potential hazards that can cause serious injury. Read

the labels and safety notes and precautions described in this manual carefully.

If a label comes off or becomes hard to read, contact you dealer for a replace -

ment.

a. Drain all gasoline from the fuel tank into an approved gasoline container.

b. Turn the engine switch ON, and loosen the carburetor drain screw and drain the

gasoline from the carburetor into a suitable container.

c. With the drain screw loosened remove the spark plug cap, and pull the starter grip

3 to 4 times to drain the gasoline from the fuel pump.

d. Turn the engine switch to the OFF position, and tighten the drain screw securely.

5.Slowly pull the starter grip until resistance is felt. At this point, the piston is coming

3. Change the engine oil.

4. Remove the spark plug and pour about a tablespoon of clean engine oil into the

cylinder.

Crank the engine several revolutions to distribute the oil, then reinstall the spark

plug.

up on its compression stroke and both the intake and exhaust valves are closed.

Storing the engine in this position will help to protect it from internal corrosion.

Safety caution

Chock Lever Fuel Cap Lever

Fuel Filler Cap

Left Side

Maintenance

Cover

Starter Grip

Engine Switch

Control Panel

Spark Plug

Maintenance Cover

Muffler

9.TRANSPORTING/STORAGE

To prevent fuel spillage when transporting or during temporary storage, the genera-

tor should be secured upright in its normal operating position, with the engine swith

OFF. Turn the cap lever fully counterclockwise to the "OFF" position.

WARNING

Gasoline is extremely flammable and explosive under

certain conditions.

Do not smoke or allow flames or sparks in the area.

3.COMPONENT IDENTIFICATION

When transporting the generator:

Do not overfill the tank (there should be no fuel in the

filler neck).

Do not operate the generator while it is on a vehicle.

Take the generator off the vehicle and use it in a well

ventilated place.

Avoid a place exposed to direct sunlight when putting

the generator on a vehicle. if the generator is left in an

enclosed vehicle for many hours, high temperature in-

side the vehicle could cause fuel to vaporize resulting in

a possible explosion.

Do not drive on a rough road for an extended period

with the generator on board, if you must transport the

generator on a rough road, drain the fuel from the gen-

erator beforehand.

Before storing the unit for an extended period:

1. Be sure the storage area is free of excessive humidity and dust.

2.Drain out the fuel completely.

Air exhauat hole

Air intake hole

5mm Screw

Muffler Protector

6mm Bolts

Muffler Gasket

Smart Throttle Switch

DC Receptacle

DC Circuit

Protector

AC Receptacle

Output Indicator Light

Overload Indicator

Light

Ground Terminal

Low Oil Alarm

Indicator Light

AC Receptacle AC Receptacle AC Receptacle

H Type (230V) AType (240V) AType (120V)

Control panel

WARNING

4.SPARK ARRESTER MAINTENANCE(Equipped type only)

If the generator has been running, the muffler will be

very hot. Allow it to cool before proceeding.

1.Remove the four 5mm screws, and remove the muffler protector.

2.Remove the four 6mm bolts, and remove the muffler, and the muffler gasket.

3.Check the muffler gasket replace if damaged. Reinstall the muffler gasket, the

muffler and the muffler protector in the reverse order of removal.

0.6-0.7mm

(0.024-0.028in)

Smart Throttle Switch

ON OFF

Never use a spark plug without damping resistance, or

it will cause no AC output.

5.Visually inspect the spark plug. Discard it if the insulator is cracked or chipped.

Clean the spark plug with a wire brush if it is to be reused.

6.Measure the plug gap with a feeler gauge.

The gap should be 0.6-0.7 mm (0.024-0.028in). Correct as necessary by carefully

bending the side electrode.

7.Install the spark plug carefully, by hand, to avoid cross-threading.

8.After a new spark plug has been seated by hand, it should be tightened 1/2 turn

with a wrench to compress its washer.

If a used plug is being reinstalled, it should only require 1 / 8 to 1/4 turn after being

seated.

9.Reinstall the spark plug cap on the spark plug securely.

10.Reinstall the spark plug maintenance cover.

CAUTION

The spark plug must be securely tightened.An improp-

erly tightened plug can become very hot and possibly

damage the generator.

Never use a spark plug with an improper heat range.

SMART throttle

Engine speed is kept at idle automatically when the electrical appliance is discon-

consumption while in operation.

trical appliance is connected. This position is recommended to minimize the fuel

nected and it returns to the proper speed to power of the electrical load when elec-

NOTE

OFF:

Note:Smart throttle system does not operate. Engine speed is kept over rated speed.

Smart throttle system does not operate effectively if the

electrical appliance requires the momentary electric power.

When high electrical loads are connected simultaneously,

turn the smart throttle switch to the OFF position to re-

duce voltage changes.

In DC operation, turn the smart throttle switch to the OFF

position

Spark Plug Maintenance Cover

Handle Bar

Plug Wrench

Spark Plug

-20- -10 0 10 20 30 40

0 20 40 60 80 100 F

Ambient Temperature

RECOMMENTED SPARK PLUG: R6-388 4.PRE-OPERATION CHECK

CAUTION

1. Check the engine oil level.

CAUTION

Be sure to check the generator on a level surface with

the engine stopped.

Using nondetergent oil or 2-stroke engine oil could shorten

the engine's service life.

Use high-detergent, premium quality 4-stroke engine oil, certified to meet or exceed

U.S.automobile manufacturer's requirements for API Service Classification SG, SF.

Select the appropriate viscosity for the average temperature in your area.

SAE Viscosity Grades

Loosen the cover screw and remove the left side maintenance cover. Remove the

oil filler cap, and wipe the dipstick with a clean rag. Check the oil level by inserting

the dipstick in the filler hole without screwing it in.

If the oil level is below the end of the dipstick, refill the recommended oil up to the top

of the oil filler neck.

NOTE

Running the engine with insufficient oil can cause serious

engine damage.

3.SPARK PLUG SERVICE

To ensure proper engine operation, the spark plug must be properly gapped and

free of deposits.

1.Remove the spark plug maintenance cover.

2.Remove the spark plug cap.

3.Clean any dirt from around the spark plug base.

4.Use the wrench to remove the spark plug.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kipor Tragbarer Generator Handbücher

Beliebte Tragbarer Generator Handbücher anderer Marken

Kohler

Kohler 20EORZ Bedienungsanleitung

Powerhorse

Powerhorse 83171 Bedienungsanleitung

HURST

HURST ML-630-SI Bedienungsanleitung

ETQ

ETQ TG4000 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton 40265 Einrichtungshandbuch

evertz

evertz 7700 Series Bedienungsanleitung

Firefly

Firefly Cygnus CYG2400/460/24 Bedienungsanleitung

Owon

Owon Waveform Generator Bedienungsanleitung

Draper

Draper PG950S Firmware-Update

SDMO

SDMO SH 4000 Bedienungsanleitung

EINHELL

EINHELL STE 5500 Bedienungsanleitung

Wanco

Wanco WI3000P Bedienungsanleitung

Full Boar

Full Boar FBT-3300 Bedienungsanleitung

Dwyer Instruments

Dwyer Instruments ASG Bedienungsanleitung

Westinghouse

Westinghouse WH1000i Series Bedienungsanleitung

Wallenstein

Wallenstein GF5000A Bedienungsanleitung

Leroy-Somer

Leroy-Somer LSA 49.1 Bedienungsanleitung

Yamakoyo

Yamakoyo SH2900DX Bedienungsanleitung