Start the installation
Installation dimensions
Garbage Disposer Dimensions
MOOr-LNO. A 8° C" D E
KCDB150 11_" 5_s/_6" 4" 6s/q6°5°
KcDa250 12_i* 5's/_" 4" 6s/_*5"
KCDC150 12_" 6"A," 4" 8'A_" 5¥,"
KCDC250 12_° 6VI°4" 7_" 5¥,"
KCDI250 13v/_6#613/16" 4" 9'/_" g_"
KCDS250 13"/_6"6_3/_6" 4" 10%B" 7_"
I_OSgSO 16V_6" 97/_6" 4" 10'/_6" 7V="
B" -Distance from bottom of sink to center
line of disposer outlet. Add 1/2 inch when ,
stainless steel sink is used.
C" - I.ength of waste hne pipe from center
line of disposer outlet to end of waste hne
pipe
IMPORTANT: Plumb waste line to prevent
standing water in the disposer motor
housing
,on! ,
Drawing shows just one model type.
Check that Jam .breakt_r
all parts were F]
included.
Mounting
assembly
sink flange
2rubber
gaskets
back-up ring
mountin S ring
and 3 screw
snap ring
Elect.rical
requirements
Electrical ground is required on this
appliance.
• * " F.
ELECTRICAL SHOCK HAZARD
•Electncal ground is required on this
appliance
•Improper connection of the equipment-
grounding conductor can result in
electrical shock.
• Check with a qualified elecmcian if you
are in doubt as to whether the
appliance is properly grounded.
•Do Not have a fuse in the neutral or
grounding circuit. A fuse in the neutral
or grounding circuit could result in
electrical shock.
Failure to follow these instructions could
result in a fire, elec_ical shock Or other
personal injury.
A. 120 Volt, 60 Hz, AC only, 15 or 20 Ampere
fused elec'_ical supply is required. (Time-
delay fuse Orcircuit breaker is recommended.)
It is recommended that a separate circuit
serving only this appliance be provided.
B. THE DISPOSER MUST BE CONNEC'[ED _._TH
COPPERWIREONLY.
C. Wire sizes and connections must conform
to the requirements of the National Elec_-ical
Code, ANSI/NFPA 70-latest edition* and all
(peal codes and Ordinaries.
D. This appliance should be connected to the
fused-disconnect (or circuit breaker) box
through flexible, armored or nonmetalhe
sheathed, copper cable (w_th grounding
wire). The flexible armored cable extending
from the appliance should be connected
directly to the junction box
E. A U L-h'sted conduit connector
must be provided at the junction
box.
It is the personal responsibility
and obligation of the customer to
contact a quahfied electhcian to
assure that the electrical installation
is adequate and iS in conformance
with the National Electrical Code
ANSI/NFPA 70-latest edition" and
all local codes and Ordinances.
Copies of the standards listed
may be obtained from:
* National Fire ProtecUon
,_ssociation
Batterymarch Park
Quincy, Massachusett_ 02269
G.For continuous feed models:
Install a 15- or 20-amp wall
s_vltch above the countertop and
junction box inside cabinet as
shown. (switch and electrical
wiring can be obtained locally)
Posit_on switch in a convenient
location Connect switch to
unction box
Go_ _
PANEL A
Remove old
disposer.
Compare your new disposer mounbng
assembly '-.'_th [he existing mounting
If the mou, itlng assembhes are the same,
complete Steps 3-A, B, D, E
A. Using a pipe wrench, disconnect tJ_edra_n
line where rtattaches to the disposer waste
hne pipe.
B. if old disposer mounting is the same as
your new one, _nsert end of jam-breaker
wrench or screwdriver into fight side of a
d_sposer mounting nng lug at top of
disposer Hold d_sposer w_th other hand
Turn jam-breaker wrench or scr_drlver
:ounterclock'vv_se until lug lines up with one
_fthe sink-mounting assembly screws
POTENTIAL PROPERTY DAMAGE
Hold disposer with one hand while
turning to prevent it from falling when
the mounting ring is disconnected.
Failure to do so could result in damage
to cabinet or floor.
Remove disposer Go to Step 3-D
C. If old disposer mounting is different from
your new one, remove the nuts on the
mount_n_ nng us_n_ pher_ or an adjustable
wrench Remove old disposer You may
need to remove a clamp or bNist the
disboser to remove it.
P.Turn disposer upside down and remove the
electrical plate
E. Use a screwdrrver [o remove the grounding
wire Remove wire nuts from power
wires Separate d_sposer Dower wires
from the cable wires Loosen screw(s)
on strain reLief and remove cable from the
disposer
If old disposer mounting is the same
as your new disposer mounting, go to
Step 5.
_- Loosen ser_s and remove the moun_mg
ring and backIU D rings A hammer may be
needed to loosen rings
G. Push Od s_nksleeve uD through the s_nkhole
and remove
H.Clean sealant from sink hole rim using a
screwdriver or putty knife tO scrape _ay air
tracesof put_ or caulking from [he s_nk hole
rim Hole nm must be as clean as poss_bre
for a good, watertight seal H'_"-_ _1
To install yoursink's first I
disposer:
/_ U_e_pnCh to loosen nutat top of
