KitchenAid 5KSM45 Series Bedienungsanleitung
Stand Mixer
5KSM45-5KSM180
W11389352A.indb 1 11/22/2019 11:52:24 AM
2 |
PARTS AND FEATURES
*Included with select models only. Also available as optional accessory.
**The bowl design and material depend on the Stand Mixer model.
1
2
4
5
611
10
1Speed control lever
2Motor head
3Attachment hub
4Attachment knob
5Motor head locking lever (not shown)
6Beater shaft
7Beater height adjustment screw
(not shown)
8Bowl clamping plate
9Bowl**
10 Pouring shield*
11 3 L stainless steel bowl*
12 Dough hook
13 Wire whip
14 Flex Edge beater*
15 Flat beater
12
13
14
15
8
9
3
7
W11389352A.indb 2 11/22/2019 11:52:25 AM
ENGLISH
| 3
STAND MIXER SAFETY
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
1. Read all instructions. Misuse of appliance may result in personal injury.
2. To protect against risk of electrical shock, do not put Stand Mixer in water or
other liquid.
3. This appliance is not intended for use by persons (including children) with
reduced physical, sensory, or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
4. Turn the appliance OFF, then unplug from the outlet when not in use, before
assembling or disassembling parts and before cleaning. To unplug, grasp
the plug and pull from the outlet. Never pull from the power cord.
5. Avoid contacting moving parts. Keep hands, hair, clothing, as well as
spatulas and other utensils away from beater during operation to reduce the
risk of injury to persons and/or damage to the Stand Mixer.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions or is dropped or damaged in any manner. Return
appliance to the nearest Authorised Service Centre for examination, repair or
adjustment.
7. The use of attachments not recommended or sold by KitchenAid may cause
fire, electrical shock or injury.
8. Do not use the Stand Mixer outdoors.
9. Do not let the cord hang over edge of table or counter.
10. Remove flat beater, wire whip, or dough hook from Stand Mixer before
washing.
W11389352A.indb 3 11/22/2019 11:52:25 AM
4 |
11. Children should be supervised to ensure that they do not play with the
appliance.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent, or similarly qualified persons in order to avoid a hazard.
13. Never leave the appliance unattended while it is in operation.
14. To avoid product damage, do not use the Stand Mixer bowls in areas of high
heat such as an oven, microwave, or on a stovetop.
15. Refer to the “Care and Cleaning” section for instructions on cleaning the
surfaces in contact with food.
16. This appliance is intended to be used in household and similar applications
such as:
- staff kitchen areas in shops, offices, or other working environments;
- farmhouses;
- by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments.
SAVE THESE INSTRUCTIONS
STAND MIXER SAFETY
ELECTRICAL REQUIREMENTS
Electrical Shock Hazard
Plug into an earthed outlet.
Do not remove earth prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these
instructions can result in
death, fire, or electrical shock.
Wattage:
300 Watts MAX
for 5KSM125 - 5KSM180 Series
275 Watts MAX
for 5KSM45, 5KSM95 Series
Voltage: 220-240 V
Hertz: 50-60 Hz
NOTE: If the plug does not fit in the
outlet, contact a qualified electrician.
Do not modify the plug in any way.
Do not use an adapter.
Do not use an extension cord. If the power
supply cord is too short, have a qualified
electrician or service technician install an
outlet near the appliance.
W11389352A.indb 4 11/22/2019 11:52:25 AM
ENGLISH
| 5
NOTE: The speed control lever can be set between the speeds listed in the above chart to
obtain speeds 3, 5, 7, and 9 if a finer adjustment is required. Do not exceed Speed 2 when
preparing yeast doughs as this may cause damage to the Stand Mixer.
SPEED CONTROL GUIDE
Speed Action Attachment Description
1Stir
For slow stirring, combining, mashing,
starting all mixing procedures. Use to add
flour and dry ingredients to batter and to
add liquids to dry ingredients. Do not use
Speed 1 to mix or knead yeast doughs.
2Slow
Mixing
For slow mixing, mashing, faster stirring.
Use to mix and knead yeast doughs,
heavy batters and candies, start mashing
potatoes or other vegetables, cut
shortening into flour, mix thin or splashy
batters.
4Mixing,
Beating
For mixing semi-heavy batters, such
as cookies. Use to combine sugar and
shortening and to add sugar to egg
whites for meringues. Medium speed for
cake mixes.
6Beating,
Creaming
For medium fast beating (creaming) or
whipping. Use to finish mixing cake,
doughnut, and other batters. High speed
for cake mixes.
8Fast
Beating,
Whipping
For whipping cream, egg whites, and
boiled frostings.
10 Fast
Whipping
For whipping small amounts of cream,
egg whites, or for final whipping of
mashed potatoes.
USING THE STAND MIXER
ACCESSORY GUIDE
Accessory Uses
Flat beater and
Flex Edge beater*
for normal to heavy mixtures:
Cakes, creamed frostings, candies,
cookies, pie pastry, biscuits, meat
loaf, mashed potatoes
Wire whip for mixtures that
need air incorporated:
Eggs, egg whites, heavy cream,
boiled frostings, sponge cakes,
mayonnaise, some candies
Dough hook for mixing and
kneading yeast doughs:
Breads, rolls, pizza dough, buns
*Included with select models only. Also available as optional accessory.
W11389352A.indb 5 11/22/2019 11:52:26 AM
6 |
ATTACHING/REMOVING THE BOWL
USING THE STAND MIXER
LIFTING/LOWERING THE MOTOR HEAD
NOTE: Motor head should always be in LOCK position when using the Stand Mixer.
To attach bowl: Turn speed control to
“0.” Unplug Stand Mixer.
1
To lift motor head: Push the locking lever
to the UNLOCK position and lift the head.
Once lifted, the lever will automatically go
back in LOCK position to keep the head
lifted.
1
Place bowl on bowl clamping plate. Turn
bowl gently in clockwise direction.
3
Hold the locking lever in the UNLOCK
position and tilt motor head back.
2
To put down motor head: Push the
locking lever to UNLOCK and gently
bring the head down. The locking lever
will automatically go back in LOCK
position when the head is down. Before
mixing, test lock by attempting to raise
motor head.
2
To remove bowl: Repeat steps 1 and 2.
Turn bowl gently counterclockwise.
4
W11389352A.indb 6 11/22/2019 11:52:26 AM
ENGLISH
| 7
USING THE STAND MIXER
*Included with select models only. Also available as optional accessory.
ATTACHING/REMOVING THE FLAT BEATER, FLEX EDGE BEATER*,
WIRE WHIP, OR DOUGH HOOK
To attach accessory: Turn speed control
to “0”. Unplug Stand Mixer.
1
To remove accessory: Repeat steps 1
and 2. Press accessory upward as far as
possible and turn to the left. Then pull
accessory from the beater shaft.
4
Hold the locking lever in the UNLOCK
position and tilt motor head back.
2
Slip accessory onto beater shaft and press
upward as far as possible. Then, turn
accessory to the right, hooking accessory
over the pin on the shaft.
3
W11389352A.indb 7 11/22/2019 11:52:26 AM
8 |
USING THE STAND MIXER
PLACING/REMOVING THE POURING SHIELD*
*Included with select models only. Also available as an optional accessory.
BEATER TO BOWL CLEARANCE
Your Stand Mixer is adjusted at the factory so the flat beater just clears the bottom of the
bowl. If, for any reason, the flat beater hits the bottom of the bowl or is too far away from
the bowl, you can correct clearance easily.
NOTE: When properly adjusted, the flat beater will not strike on the bottom or side of
the bowl. If the flat beater or the wire whip is so close that it strikes the bottom of the
bowl, coating may wear off the beater or wires on whip may wear.
Turn speed control to “0”. Unplug Stand
Mixer.
1
To place pouring shield: Turn speed
control to “0”. Unplug Stand Mixer.
Attach your chosen accessory. See the
“Attaching/removing the flat beater, wire
whip, or dough hook” section.
1
Lift motor head. Turn screw slightly
counterclockwise (left) to raise flat beater
or clockwise (right) to lower flat beater.
Make adjustment with flat beater, so
it just clears surface of bowl. If you
overadjust the screw, the bowl lock lever
may not lock into place.
2
From the front of the Stand Mixer, slide
the pouring shield over the bowl until the
shield is centred. The bottom rim of the
shield should fit within the bowl.
2
W11389352A.indb 8 11/22/2019 11:52:27 AM
ENGLISH
| 9
USING THE STAND MIXER
USING THE POURING SHIELD*
Use the pouring shield to avoid having ingredients splashing out of the bowl when
mixing, as well as to easily pour ingredients in the bowl while mixing.
*Included with select models only. Also available as an optional accessory.
To remove pouring shield: Turn speed
control to “0”. Unplug Stand Mixer.
3
Lift the front of the pouring shield clear
of the bowl rim and pull forward. Remove
attachment and bowl.
4
For best results, rotate the shield so the
motor head covers the U-shaped gap in
the shield. The pouring chute will be just
to the right of the attachment hub asyou
face the Stand Mixer.
1
Pour the ingredients into the bowl
through the pouring chute.
2
W11389352A.indb 9 11/22/2019 11:52:27 AM
10 |
USING THE STAND MIXER
OPTIONAL ATTACHMENTS
KitchenAid offers a wide range of optional attachments such as food grinders or
pasta makers. They may be attached to the Stand Mixer attachment power shaft,
as shown here.
OPERATING THE SPEED CONTROL
NOTE: The Stand Mixer may warm up during use. Under heavy loads with extended
mixing time, the top of the unit may become hot. This is normal.
Plug Stand Mixer into proper electrical
outlet. Always set speed control lever
on lowest speed to start, then gradually
increase speed to avoid splashing
ingredients. See “Speed control guide”
chart.
1
To attach: Turn speed control to “0”.
Unplug Stand Mixer.
1
Do not scrape bowl while Stand Mixer
is operating. The bowl and beater are
designed to provide thorough mixing
without frequent scraping. Scraping
the bowl once or twice during mixing is
usually sufficient.
2
Loosen attachment knob by turning it
counterclockwise. Remove attachment
hub cover.
2
W11389352A.indb 10 11/22/2019 11:52:27 AM
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere KitchenAid Mischer Handbücher
KitchenAid
KitchenAid KSM7581BZ0 Kurzanleitung
KitchenAid
KitchenAid 5KSM3311 Bedienungsanleitung
KitchenAid
KitchenAid KSM500QAC0 Kurzanleitung
KitchenAid
KitchenAid 5K45SS Bedienungsanleitung
KitchenAid
KitchenAid 5KSM55 Bedienungsanleitung
KitchenAid
KitchenAid 5KSM1CBT Bedienungsanleitung
KitchenAid
KitchenAid Mixer Kurzanleitung
KitchenAid
KitchenAid 5KSM150PS Bedienungsanleitung
KitchenAid
KitchenAid KSM7586PCA Bedienungsanleitung
KitchenAid
KitchenAid 9KSM160FGA Bedienungsanleitung
KitchenAid
KitchenAid 5K45 Series Bedienungsanleitung
KitchenAid
KitchenAid K48750 Bedienungsanleitung
KitchenAid
KitchenAid KSM500ER0 Bedienungsanleitung
KitchenAid
KitchenAid KSMCB5 Bedienungsanleitung
KitchenAid
KitchenAid KSM7581BZ Bedienungsanleitung
KitchenAid
KitchenAid KP26M1XPM - Mixer 6QT, Pearl Metallic Bedienungsanleitung
KitchenAid
KitchenAid 3KSMC895 Bedienungsanleitung
KitchenAid
KitchenAid KSM75WH1 Bedienungsanleitung
KitchenAid
KitchenAid *521.004 Bedienungsanleitung
KitchenAid
KitchenAid 6397dZw608 Kurzanleitung
