KitchenAid 5KSM7586P Bedienungsanleitung

KEC97A

5KSM7586P

7KSM7586P

W10860998A_ENv02.indd 1 1/14/16 1:51 PM

STAND MIXER INSTRUCTIONS

STAND MIXER SAFETY

Important safeguards��3

Electrical requirements ��5

Electrical requirements for Brazil only ��6

PARTS AND FEATURES��7

ASSEMBLING THE STAND MIXER

Attaching the bowl and beaters��8

Adjusting the beater to bowl clearance�� 9

OPERATING THE STAND MIXER

Speed control guide – 10-speed Stand Mixers ��10

Removing the bowl and beaters��11

TIPS FOR GREAT RESULTS

Stand Mixer use��11

Mixing time�� 12

Mixing tips ��12

ATTACHMENTS ��12

CARE AND CLEANING�� 13

TROUBLESHOOTING�� 14

TECHNICAL INFORMATION�� 14

ENVIRONMENTAL ISSUES�� 15

TECHNICAL ASSISTANCE OR SERVICE ��15

TABLE OF CONTENTS

W10860998A_ENv02.indd 2 1/14/16 1:51 PM

English

STAND MIXER INSTRUCTIONS

STAND MIXER SAFETY

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions

should always be followed, including the following:

1. Read all instructions� Misuse of appliance may result in

personal injury�

2. To avoid risk of electrical shock, do not put Stand Mixer in

water or other liquid�

3. This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety�

4. Children should be supervised to ensure that they do not

play with the appliance�

5. Unplug Stand Mixer from outlet when not in use, before

putting on or taking off parts, and before cleaning�

6. Avoid contacting moving parts� Keep hands, hair, and

clothing, as well as spatulas and other utensils away from

beater during operation to reduce the risk of injury to

persons and/or damage to the Stand Mixer�

W10860998A_ENv02.indd 3 1/14/16 1:51 PM

STAND MIXER SAFETY

SAVE THESE INSTRUCTIONS

7. Do not operate Stand Mixer with a damaged cord or plug

or after the Stand Mixer malfunctions, or is dropped or

damaged in any manner� Return appliance to the nearest

Authorized Service Center for examination, repair or

electrical or mechanical adjustment�

8. The use of attachments not recommended or sold by

KitchenAid may cause re, electrical shock, or injury.

9. Do not use the Stand Mixer outdoors�

10. Do not let the cord hang over edge of table or counter�

11. Remove Flat Beater, Stainless Steel Whip, or Spiral Dough

Hook from Stand Mixer before washing�

12. To avoid product damage, do not use the mixer bowls in

areas of high heat such as an oven, microwave, or on a

stovetop�

13. Do not use the Stand Mixer on or next to an electric or gas

oven, or put it inside of a warm oven�

14. Do not use the Stand Mixer for anything other than its

intended function as specied in this manual.

15. Do not use toxic products (alcohol, ammonia, stain

removers, etc�) or steel sponges to clean the Stand Mixer�

These products may damage the Stand Mixer or leave

undesirable odors�

16. This product is designed for household use only.

STAND MIXER SAFETY

W10860998A_ENv02.indd 4 1/14/16 1:51 PM

English

STAND MIXER SAFETY

Volts: 127-220 A�C�

Hertz: 60 Hz

Wattage: 500 Watts

NOTE: Use an appropriate outlet to plug in

your Stand Mixer� If the plug does not fit in

the outlet, contact a qualified electrician� Do

not modify the plug in any way� Do not use

adapters or T’s�

Do not use an extension cord� If the power

supply cord is too short, have a qualified

electrician or serviceman install an outlet

near the appliance�

Electrical requirements

W10860998A_ENv02.indd 5 1/14/16 1:51 PM

PARTS AND FEATURES

STAND MIXER SAFETY

Residence mains:

The mains wires must be of copper

with a minimum cross-section per ABNT

(NBR-5410�)

To protect this appliance and the mains

against over loading, this appliance must

be connected to a circuit that is protected

with a thermo-magnetic circuit breaker�

If the household circuit does not include

a circuit breaker, contact an electrician

to have one installed�

Electric outlet:

For your safety and to avoid damage

to your product, it is very important

that your product is earthed correctly�

Your appliance power cord features a

3-pin-shaped hexagon-shaped plug,

10A, per ABNT (NBR 14136)�

Your residence electrical installation

must have a suitable electric outlet

for this type of plug� If not, it is your

responsibility to have one installed

by a qualified electrician�

Use appropriate outlet type for your

appliance plug, as shown below:

Before operating

this appliance, make

sure the main voltage

at the installation site

is the same as indicated

on product technical

data label�

This information is also included on the

label attached to your appliance’s cord

near the plug�

IMPORTANT:

• If it is necessary to convert your

127V appliance to 220V, use a

1�0 KVA stabiliser�

• If it is necessary to convert your

220V appliance to 127V, use a

1�0 KVA stabiliser�

• Never plug your

appliance into

multi-plug adapters

with another

appliance in the same

socket� Do

not use an extension

cord� This type of connection may cause

electrical overload in the mains, and can

damage the appliance and could cause a

fire� The appliance should be plugged into

its own outlet�

• In case of oscillation in mains voltage,

install an automatic voltage stabiliser with

minimum rating of 1000 Watts between

the appliance and the socket�

• If the cord of this appliance is damaged, it

must be replaced� Contact your nearest

authorized KitchenAid Customer Care

Center�

Electrical requirements (for Brazil only)

W10860998A_ENv02.indd 6 1/14/16 1:51 PM

English

PARTS AND FEATURES

Speed control

lever

Bowl lift lever

(not shown)

Beater Shaft

Wire whip

Bowl

Dough hook

Flat beater

Locating pins

Bowl support

Beater height

adjustment

screw

Motor head

Bowl

handle

Attachment hub

(see the “Attachments”

section)

Attachment

knob

Pouring shield

STAND MIXER SAFETY

W10860998A_ENv02.indd 7 1/14/16 1:51 PM

MONTANDO A BATEDEIRA PROLINE

Anexando a tigela e os batedores

;

1 2

Desligue a batedeira mudando o

controle de velocidade para “0”

(desligar) e retire o plugue da

tomada.

Posicione a alavanca de

elevação da tigela para baixo.

Encaixe o suporte da tigela

sobre os pinos de fixação;

pressione a parte de trás da

tigela até o pino da tigela

encaixar na mola.

Para usar o protetor de respingos,

na frente da batedeira, deslize o

protetor até centralizá-lo sobre a

borda da tigela.

A borda inferior do protetor deve

encaixar dentro da tigela.

Deslize o batedor (batedor

plano, batedor em gancho ou

batedor de aço inoxidável) sobre

o eixo do batedor e pressione

para cima o máximo possível.

Gire o batedor para a direita,

engatando-o no eixo do batedor.

Levante a tigela até a posição de

mistura, girando a alavanca de

elevação no sentido anti-horário

até a posição para cima. A tigela

deve sempre ficar na posição

para cima durante a mistura.

Mola

Pino de fixação

Protetor de

respingos.

Nota: Gire o protetor de respingos de modo que o motor da batedeira cubra a

abertura em forma de U do protetor. O protetor ficará à direita do eixo conector

quando a batedeira é vista de frente.

ASSEMBLING THE STAND MIXER

Locating Pin

Spring Latch

Pouring Chute

1Turn speed control to “0” (OFF), and

unplug Stand Mixer�

Attaching the bowl and beaters

2Place bowl lift lever into down position�

3Fit bowl supports over locating pins;

press down on back of the bowl until

bowl pin snaps into the spring latch� If

not securely snapped into place, bowl

will be unstable and wobble during use�

5If using the pouring shield, from the

front of the Stand Mixer, slide the

pouring shield over the bowl until it

is centered� The bottom rim of the

pouring shield should fit within the

bowl�

4Slip a beater (flat, wire whip, or dough

hook) onto the beater shaft and press

upward as far as possible� Turn beater

to the right, hooking it over the pin on

the beater shaft�

NOTE: Rotate the pouring shield so the

motor head covers the U-shaped gap in

the shield� The pouring chute will be just

to the right of the attachment hub as you

face the Stand Mixer�

6Raise the bowl into mixing position

by rotating the bowl lift lever

counterclockwise to the straight up

position� The bowl must always be

in the raised position when mixing�

ASSEMBLING THE STAND MIXER

W10860998A_ENv02.indd 8 1/14/16 1:51 PM

English

MONTANDO A BATEDEIRA PROLINE

Anexando a tigela e os batedores

;

1 2

Desligue a batedeira mudando o

controle de velocidade para “0”

(desligar) e retire o plugue da

tomada.

Posicione a alavanca de

elevação da tigela para baixo.

Encaixe o suporte da tigela

sobre os pinos de fixação;

pressione a parte de trás da

tigela até o pino da tigela

encaixar na mola.

Para usar o protetor de respingos,

na frente da batedeira, deslize o

protetor até centralizá-lo sobre a

borda da tigela.

A borda inferior do protetor deve

encaixar dentro da tigela.

Deslize o batedor (batedor

plano, batedor em gancho ou

batedor de aço inoxidável) sobre

o eixo do batedor e pressione

para cima o máximo possível.

Gire o batedor para a direita,

engatando-o no eixo do batedor.

Levante a tigela até a posição de

mistura, girando a alavanca de

elevação no sentido anti-horário

até a posição para cima. A tigela

deve sempre ficar na posição

para cima durante a mistura.

Mola

Pino de fixação

Protetor de

respingos.

Nota: Gire o protetor de respingos de modo que o motor da batedeira cubra a

abertura em forma de U do protetor. O protetor ficará à direita do eixo conector

quando a batedeira é vista de frente.

ASSEMBLING THE STAND MIXER

NOTE: When properly adjusted, the at

beater will not strike on the bottom or

side of the bowl. If the at beater or the

wire whip is so close that it strikes the

bottom of the bowl, the coating may wear

off the at beater (for coated beaters) or

wires on the wire whip may wear�

Scraping sides of bowl may be necessary

under certain conditions regardless of

beater adjustment� The Stand Mixer must

be stopped to scrape bowl or damage to

Stand Mixer may occur�

Adjusting beater to bowl clearance

Your Stand Mixer is adjusted at the factory so the at beater just clears the bottom of the

bowl. If, for any reason, the at beater hits the bottom of the bowl or is too far away from

the bowl, you can correct the clearance easily�

2Lower the bowl to the down position�

3Turn beater height adjustment screw

(A) slightly counterclockwise (left) to

raise the flat beater; or turn clockwise

(right) to lower the flat beater� Adjust

so that the flat beater just clears the

surface of the bowl� If you over adjust

the screw, the bowl lift lever may not

lock in place�

1Turn speed control to “0” (OFF), and

unplug Stand Mixer�

W10860998A_ENv02.indd 9 1/14/16 1:51 PM

Speed Used For Accessories Description

1 Stirring For slow stirring, combining, mashing,

starting all mixing procedures� Use to add

flour and dry ingredients to batter, and add

liquids to dry ingredients� Do not use Speed

1 to mix or knead yeast doughs�

2Slow mixing,

Kneading

For slow mixing, mashing, faster stirring�

Use to mix and knead yeast doughs, heavy

batters, and candies; start mashing potatoes

or other vegetable; cut shortening into flour;

mix thin or splashy batters�

4 Mixing,

Beating

For mixing semi-heavy batters, such

as cookies� Use to combine sugar and

shortening and to add sugar to egg whites for

meringues� Medium speed for cake mixes�

6 Beating,

Creaming

For medium-fast beating (creaming) or

whipping� Use to finish mixing cake,

doughnut, and other batters� High speed for

cake mixes�

8-10 Fast beating,

Whipping,

Fast Whipping

For whipping cream, egg whites, and boiled

frostings� For whipping small amounts of

cream, egg whites or for final whipping of

mashed potatoes�

OPERATING THE STAND MIXER

NOTE: Use Speed 2 to mix or knead yeast doughs� Use of any other speed creates high

potential for Stand Mixer failure. The dough hook efciently kneads most yeast dough

within 4 minutes�

Speed control guide – 10-speed Stand Mixers

W10860998A_ENv02.indd 10 1/14/16 1:51 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere KitchenAid Mischer Handbücher

KitchenAid

KitchenAid KSM3311 Bedienungsanleitung

KitchenAid

KitchenAid K48750 Bedienungsanleitung

KitchenAid

KitchenAid 5-qt. - Pro 500 Series Stand Mixer Bedienungsanleitung

KitchenAid

KitchenAid 3KSM55 Bedienungsanleitung

KitchenAid

KitchenAid KSM175 Bedienungsanleitung

KitchenAid

KitchenAid 5K45SS Bedienungsanleitung

KitchenAid

KitchenAid KSM150PS - Artisan Series Mixer Bedienungsanleitung

KitchenAid

KitchenAid 5KSM3311X Bedienungsanleitung

KitchenAid

KitchenAid KSM3316X Bedienungsanleitung

KitchenAid

KitchenAid KSM95ER - 4.5-qt. Ultra Power Stand Mixer Bedienungsanleitung

KitchenAid

KitchenAid K45SSAC-0 Bedienungsanleitung

KitchenAid

KitchenAid KSM3316XWH0 Bedienungsanleitung

KitchenAid

KitchenAid KSM150AGBCA0 Bedienungsanleitung

KitchenAid

KitchenAid KHM7TWH0 Bedienungsanleitung

KitchenAid

KitchenAid K4SSWH - 4.5-qt. Bowl-Lift Stand Mixer Kurzanleitung

KitchenAid

KitchenAid 5KSMC895Z Bedienungsanleitung

KitchenAid

KitchenAid KSM95GR - Ultra Power Stand Mixer Bedienungsanleitung

KitchenAid

KitchenAid KV25 Bedienungsanleitung

KitchenAid

KitchenAid KSM8990ER Bedienungsanleitung

KitchenAid

KitchenAid KHM7T - Ultra Power Plus Hand Mixer Kurzanleitung

KitchenAid

KitchenAid Bowl-Lift Mixer Bedienungsanleitung

KitchenAid

KitchenAid KSM70SN Bedienungsanleitung

KitchenAid

KitchenAid 5KSM7990 Bedienungsanleitung

KitchenAid

KitchenAid KEA25A Bedienungsanleitung

Beliebte Mischer Handbücher anderer Marken

Bosch

Bosch GRW 9 Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman WM45E Leitfaden

Jay-Lor

Jay-Lor 5050 Bedienungsanleitung

Sunbeam

Sunbeam FPSBSM210X Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman MC94S Leitfaden

Thinky

Thinky ARE-250 Bedienungsanleitung

Midas

Midas XL4 Bedienungsanleitung

bianco

bianco PURO 4 Bedienungsanleitung

Paso

Paso DAG9200 Bedienungsanleitung

Sima

Sima SFX-9A Bedienungsanleitung

better chef

better chef IM-815WC Montageanleitung

ALLEN & HEATH

ALLEN & HEATH GR1 Bedienungsanleitung

Lacor

Lacor 69083 Technisches Datenblatt

M-Audio

M-Audio Midiman SAM Bedienungsanleitung

Buffalo

Buffalo CP921 Bedienungsanleitung

Pentair

Pentair HYPRO Cleanload 3376-0870 Betriebsanleitung

Cuisinart

Cuisinart SM50WHE Bedienungsanleitung

Hobart

Hobart HCM-300 Bedienungsanleitung