KMC Controls CSC 3000 Series Benutzerhandbuch

Replacing CSC-1001 with CSC-2000/3000 Series Controllers 1 Application Guide, AN0811A Rev. A

CSC-1001 Function

The CSC-1001 is designed for use with normally

open dampers in either of the following applications:

• Constant air volume (CAV) terminals

• Variable air volume (VAV) terminals with maxi-

mum ow limiting

CAV operation is congured by connecting a nor-

mally open actuator to the C port on the controller

(or the H port if the T port is open) and adjusting the

setpoint screw to the desired ow setpoint. Airow

is measured by an SSS-1000 series sensor connected

between the HI and LO ports. Adjusting the setpoint

screw clockwise will increase the ow setpoint;

adjusting the screw counter-clockwise will decrease

the ow setpoint. The T port may be exhausted to

atmosphere during constant volume operation.

When used in VAV applications where a high ow

limit is necessary, the controller should have a

normally open damper connected to the H port, a

reverse acting thermostat connected to the T port,

and an SSS-1000 series ow pickup between HI and

LO. The C port should be capped (as installed from

the factory). With the T port exhausted, or at a low

pressure, the setpoint screw can be adjusted for the

maximum ow limit. The controller will supply the

H port with the higher of either the thermostat signal

or the congured maximum ow limit pressure, thus

limiting the maximum airow once the thermostat

signal falls below the maximum ow setpoint.

Replacing CSC-1001 Controllers

with CSC-2000/3000 Series Controllers

Overview ...............................................................1

Important Notices .................................................1

CSC-1001 Function ...............................................1

Sample Applications ..............................................2

Replacement by CSC-2001/2003 ...........................3

Replacement by CSC-3011 .................................... 3

Overview

CSC-1001 Constant Volume Controllers have been

discontinued. However, they can be replaced with a

CSC-2001/2003/3011 controller and (for VAV applica-

tions) an RCC-1008/1108 relay.

For more information about a particular device, see

the respective device data sheet, installation guide,

and/or application guide.

Application Guide

CSC-1001

CSC-3011

Important Notices

The material in this document is for information

purposes only. The contents and the product it

describes are subject to change without notice. KMC

Controls, Inc. makes no representations or warran-

ties with respect to this document. In no event shall

KMC Controls, Inc. be liable for any damages, direct

or incidental, arising out of or related to the use of

this document.

Replacing CSC-1001 with CSC-2000/3000 Series Controllers 2 Application Guide, AN0811A Rev. A

B M

SSS-1000 Series

Airflow Sensor

Constant Volume Application

CSC-2001/2003

Reset Volume

Controller

Actuator

H L T

M NO

DAMPER

CSC-3011

Reset Volume

Controller

Actuator

Constant Volume Airflow adjusted using

the LO Adjustment Knob (center knob)

B M

L M

B M

SSS-1000 Series

Airflow Sensor

VAV Application with a High Flow Limit

RCC-1008/1108

High Pressure

Selector Relay

CSC-2001/2003

Reset Volume

Controller

Thermostat

RA Cool

DA Heat

Actuator

High Flow adjusted using the LO

Adjustment Knob (center knob)

H L T

M NO

DAMPER

CSC-3011

Reset Volume

Controller

NOTE: OntheCSC-3011,ensuretheDamper

ActionSelectionDialissetproperly

(NormallyOpenintheseexamples).

Sample Applications

Replacing CSC-1001 with CSC-2000/3000 Series Controllers 3 Application Guide, AN0811A Rev. A

KMCControls,Inc.

19476 Industrial Drive

New Paris, IN 46553

574.831.5250

www.kmccontrols.com

[email protected]

Replacement by CSC-3011

A CSC-3011 “universal” Reset Volume Controller

may also be used to obtain the same functionality of

CSC-1001 Constant Volume Controllers. For constant

volumeapplications, a CSC-3011 should be used in

conjunction with a normally open actuator (connect-

ed to the B port) and an SSS-1000 series ow pickup

(connected between H and L). The T port should be

exhausted. The LO Stat (“low thermostat dierential

pressure”) adjustment knob (center knob) may be set

to maintain the desired constant volume airow. (See

the Constant Volume Application illustration on the

previous page.)

EnsuretheDamperActionSelectionDialisset

properly(NormallyOpenintheseexamples).

VAVapplicationsrequiringahighlimit should be

replaced with a CSC-3011 and an RCC-1008/1108

High Selector Relay. The normally open actuator

should be connected to the B port of the RCC. The

S1 and S2 ports of the RCC should be supplied from

the B ports of the CSC-3011 and a reverse acting

thermostat. The high ow limit can be adjusted using

the LO Stat adjustment knob on the CSC-3011. An

SSS-1000 series ow pickup should be connected be-

tween the H and L ports of the CSC-3011, and the T

port should be exhausted. (See the VAV Application

with a High Flow Limit illustration on the previous

page.)

ForCSC-3011adjustmentandotherinformation,

seetheCSC-3000seriesApplicationGuide.

Replacement by CSC-2001/2003

CSC-2000 Series Reset Volume Controllers may be

used to obtain the same functionality of CSC-1001

Constant Volume Controllers. For constantvolume

applications, a CSC-2001/2003 should be used in

conjunction with a normally open actuator (connect-

ed to the B port) and an SSS-1000 series ow pickup

(connected between X and Y). The T port should be

exhausted. The LO adjustment knob (center knob on

the front) may be set to maintain the desired constant

volume airow. (See the Constant Volume Applica-

tion illustration on the previous page.)

VAVapplicationsrequiringahighlimit can be re-

placed with a CSC-2001/2003 and an RCC-1008/1108

High Selector Relay. The normally open actuator

should be connected to the B port of the RCC. The

S1 and S2 ports of the RCC should be supplied from

the B ports of the CSC-2001/2003 and a reverse acting

thermostat. The high ow limit can be adjusted us-

ing the LO adjustment knob on the CSC-2001/2003.

An SSS-1000 series ow pickup should be connected

between the X and Y ports of the CSC-2001/2003, and

the T port should be exhausted. (See the VAV Ap-

plication with a High Flow Limit illustration on the

previous page.)

ForCSC-2001/2003adjustmentandotherinforma-

tion,seetheCSC-2000seriesApplicationGuide.

Andere Handbücher für CSC 3000 Series

Dieses Handbuch passt für folgende Modelle

Andere KMC Controls Controller Handbücher

KMC Controls

KMC Controls BAC-9001CE Bedienungsanleitung

KMC Controls

KMC Controls BAC-7001 Bedienungsanleitung

KMC Controls

KMC Controls AppStat Bedienungsanleitung

KMC Controls

KMC Controls MEP-1500 Series Bedienungsanleitung

KMC Controls

KMC Controls MCP-1160 Series Bedienungsanleitung

KMC Controls

KMC Controls KMD-7001 Original Betriebsanleitung

KMC Controls

KMC Controls MEP-4 Series Benutzerhandbuch

KMC Controls

KMC Controls MEP-4201 Bedienungsanleitung

KMC Controls

KMC Controls CSP-4702 Bedienungsanleitung

KMC Controls

KMC Controls CSC-3501 Bedienungsanleitung

KMC Controls

KMC Controls BAC-7401 Betriebsanleitung

KMC Controls

KMC Controls KMD-5210 Betriebsanleitung

KMC Controls

KMC Controls BAC-9300 Series Bedienungsanleitung

KMC Controls

KMC Controls MEP-3001 Betriebsanleitung

KMC Controls

KMC Controls SimplyVAV BAC-8001 Benutzerhandbuch

KMC Controls

KMC Controls MEP-7 Series Benutzerhandbuch

KMC Controls

KMC Controls BAC-7302 Betriebsanleitung

KMC Controls

KMC Controls KMD-5831 Original Betriebsanleitung

KMC Controls

KMC Controls CEE-3009 Bedienungsanleitung

KMC Controls

KMC Controls CSC-1001 Bedienungsanleitung

KMC Controls

KMC Controls MEP-46 Q Series Bedienungsanleitung

KMC Controls

KMC Controls BAC-5901C-AFMS Bedienungsanleitung

KMC Controls

KMC Controls MEP-5062 Bedienungsanleitung

KMC Controls

KMC Controls CTE-3017 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch