KNX Module IC-IP-S.1.0 Bedienungsanleitung

module-electronic.ru

KNX IP INTERFACE

IC-IP-S.1.0

Application Program: ver. 1.0

User Manual: ver. 1.0

User Manual

CONTENT

Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1 Basic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Speciﬁcation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 KNXnet/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 IP tunneling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 IP routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 IP bootloader / boot mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Operational description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.1 IP interface application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.2 IP network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.3 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3.1 Programming button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3.2 Individual address assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.4 Function button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.4.1 Factory reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.4.2 Boot mode activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.4.3 LED status display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 ETS database parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2 IP conﬁguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Web front-end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.1 Accessing the IC-IP-S.1.0 web front-end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.1.1 Via windows network UPnP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.1.2 Via IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.1.3 Via MAC address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.2 Device info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.3 KNX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.4 Firmware update / boot mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5.5 IP tunneling address assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6 State of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.1 Default factory setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

7 Legal Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

page 2

module-electronic.ru

1 BASIC INFORMATION

The KNX IP interface provides access to the KNX bus from the Ethernet network using the KNXnet/IP

protocol. Using to conﬁgure, monitor, visualize and manage devices on the KNX network.

• Protocol KNXnet/IP

• Up to 4 connections simultaneously

• Ethernet 10/100 BaseT IP

• LED status indication

• Long telegrams with up to 240 bytes APDU length are supported

• WEB interface for monitoring status and device settings

• Remote ﬁrmware update

• Power supply via KNX bus

• DIN rail 35mm mounting

IC-IP-S.1.0

page 3

module-electronic.ru

1.1 SPECIFICATION

Device model

IC-IP-S.1.0

Inputs

Ethernet connector

RJ45, female

KNX interface

Speciﬁcation

TP-256

Available application soware

ETS 4 and later

KNX connector

4-wire EIB connector (PUSH WIRE spring clips) for standard cable TP1 0,8мм Ø

Supported protocols

KNXnet/IP, ARP, ICMP, IGMP, HTTP, UPnP discovery, UDP/IP, TCP/IP, DHCP и AutoIP

KNX physical address by default

15.15.0

Power supply

via KNX bus: 21...30В DC

Consumption on the KNX bus (29V DC)

< 20mA

< 600mW

Operation temperature

-5°C ... + 45°C

Operation humidity

5 ... 95% (no condensation)

Degree of protection

IP 20, clean environment

Mounting type

DIN rail 35mm

Dimensions

36 х 90 х 71mm (2TE)

Weight

68 g

page 4

module-electronic.ru

1.2 APPEARANCE

90mm

36mm 71mm

A. Ethernet connector B. Function button C. Programming button D. KNX TP connector

1. LED IP state 2. LED bus state KNX TP 3. LED telegram traﬀic IP

4. LED telegram traﬀic KNX TP 5. Programming LED

1. IP state

Green: IP line OK

OFF: No IP connection

2. Bus state KNX TP

Green: KNX TP line OK

OFF: KNX TP line not connection

3. Telegram traﬀic IP

Green (blinking): Telegram traﬀic

Red (blinking): Transmission error

OFF: No telegram traﬀic

4. Telegram traﬀic KNX TP

Green (blinking): Telegram traﬀic

Red (blinking): Transmission error

OFF: No telegram traﬀic

5. Programming

Red: Programming Mode / Boot Mode active

Red (blinking): No IP connection

OFF: Programming Mode / Boot Mode not active

page 5

module-electronic.ru

KNX bus

Ethernet

ATTENTION! Installation and connection of the device to the mains must only be carried

out by qualiﬁed personnel! Be sure to turn oﬀ the power before installing or removing the

device! Even when the device is turned oﬀ, the output terminals can be live! Do not

connect to the outputs a load that exceeds the recommended values! The design of the

device meets the requirements of electrical safety according to GOST 12.2.007.0-75.

1.3 INSTALLATION AND CONNECTION

INSTALLATION

WIRING DIAGRAMS

Attaching to DIN rail

Removing from DIN rail

page 6

module-electronic.ru

2 KNXnet/IP

IC-IP-S.1.0 is a KNX IP interface. KNX IP interfaces are highly similar to USB interfaces. The only diﬀerence

is that they use the IP communication medium and the KNXnet/IP communication protocol. However,

KNX end devices can be integrated directly via IP. This makes the Ethernet a real KNX medium.

As documented in the KNXnet/IP protocol speciﬁcations, KNX telegrams can be transmitted encapsulated

in IP packets. Ethernet networks as well as Internet can be used to route or tunnel KNX telegrams. In this

way, IP interfaces and IP routers are an alternative to USB data interfaces and TP line/area/backbone

couplers, respectively. In the latter case, a TP backbone can be completely replaced by a fast Ethernet

based line then called IP backbone.

The presence of the Internet Protocol (IP) has led to the deﬁnition of the KNXnet/IP protocol. KNXnet/IP

oﬀers the possibility for point-to-point connections for the ETS (KNXnet/IP Tunneling) and/or between

supervisory system and KNX installation. The KNXnet/IP device management enables KNXnet/IP device

conﬁguring via the KNX network in order to reduce the time required for complete network conﬁguration.

2.1 IP TUNNELING

2.2 IP ROUTING

IP Routing is the way of interconnecting KNX lines and areas by IP network(s) via KNXnet/IP. In IP

networks, the KNXnet/IP Routing deﬁnes the way of KNXnet/IP router communication.

2.3 IP BOOTLOADER / BOOT MODE

The IP bootloader function is used to update the ﬁrmware and completely rewrite the ﬂash memory

content. This is not just a simple application download. Both communication stack and application

soware are downloaded.

The ﬁrmware update procedure via IP is executed by a web front-end, which is independent from ETS,

and makes use of special messages to speed up the process. To be protected, their contents are

encrypted.

Entering Boot Mode is equivalent to activating the IP bootloader function.

page 7

module-electronic.ru

3 OPERATIONAL DESCRIPTION

In network installations IC-IP-S.1.0 is used as KNX IP interface. Aer connecting to KNX TP, IC-IP-S.1.0

operates with its default settings. Setting the correct Individual Address is necessary to include IC-IP-S.1.0

in the present KNX bus system.

3.2 IP NETWORK

IC-IP-S.1.0 sends telegrams from/to the TP network to/from the IP network in accordance with the

KNXnet/IP protocol speciﬁcation. Important notes:

џAll KNX IP devices that are intended to communicate with each other via IP must have the same IP

multicast address.

џIf the IP address is changed from the IP side it may happen that ETS does no longer recognize the

device and connection cannot be maintained (tunneling uses IP addresses). So, it is recommended

to change IP addresses and restart only from TP side.

џIf problems occur for IP address assignment please ask your network administrator.

џAccording to the topology, the Tunneling addresses always have to be assigned in the range of

subline addresses. For more information about additional Individual Addresses for tunneling

please refer to IP Tunneling Address Assignment.

џTo program devices of a line diﬀerent to which the device used for (re)programming is connected,

the use of a correct topology is mandatory!

3.1 IP INTERFACE APPLICATION

IP Interface is designed for use in 10/100 BaseT networks compliant to IEEE802.3. The AutoSensing

function sets the baud rate (10 Mbit or 100 Mbit) automatically. IP address can be received from a DHCP

server. For this, the automatic assignment setting of the IP address can be set by ETS (use DHCP). If set so

and no DHCP server is found, IC-IP-S.1.0 starts an AutoIP procedure and autonomously assigns the IP

address. The IP address that IC-IP-S.1.0 receives during its start-up (via DHCP or AutoIP) is retained until

next start-up (e.g. due to power oﬀ or reprogramming). If IC-IP-S.1.0 is supposed to have a ﬁxed IP address

(as well as subnet mask and standard gateway) it can be set by ETS.

ETS does not provide an unload procedure for applications.

page 8

module-electronic.ru

3.3.2 INDIVIDUAL ADDRESS ASSIGNMENT

To download the desired Individual Address or an ETS setting the Programming Mode must be activated.

Successive pressing the Programming Button will turn on and oﬀ the Programming Mode. LED 7 lighting

in red colour indicates Programming Mode is active. When Programming Mode is activated, the ETS is

able to download the Individual Address.

A blinking red Programming LED indicates the Ethernet cable is not properly connected or no IP

network connection is available.

Also when Boot Mode is active, successive pressing the Programming Button will turn on and oﬀ

Programming Mode and Programming LED.

To conﬁgure the device an interface connection (IP, USB) to the KNX bus system is required. The device is

supplied with the Individual Address 15.15.0. The KNX product database entry (available for ETS4 and

higher) can be downloaded from the website and from the KNX Online Catalog.

The Individual Address can be assigned to the device by setting the desired address in the properties

window of the ETS. Aer starting the ETS download and then pressing the Programming Button the

device restarts itself.

3.3 PROGRAMMING

3.3.1 PROGRAMMING BUTTON

Figure 1. ETS properties window

page 9

module-electronic.ru

3.4 FUNCTION BUTTON

The Function Button activates IC-IP-S.1.0´s special function. Factory Reset can be activated. Device

settings of IC-IP-S.1.0 can be reset to manufacturer default values with the Factory Reset function. During

the ﬁrmware update procedure the Function Button has to be pressed for Boot Mode activation.

3.4.1 FACTORY RESET

A long press (≈ 15 sec) of the Function Button soon followed by a short press (≈ 3 sec) executes the Factory

Reset. Aer the ﬁrst press, the LED display lights like described in Table 1. Aer the second press, all

parameters will be set to factory default (incl. Individual Address). Subsequently, LEDs indicate normal

operation again.

3.4.2 BOOT MODE ACTIVATION

For Boot Mode activation the ﬁrmware update process must be executed. During the process, the

Function Button must be pressed to enter Boot Mode (see chapter 5.4).

Figure 2. Boot Mode is active

page 10

module-electronic.ru

Inhaltsverzeichnis

Andere KNX Netzwerk-Hardware Handbücher

KNX

KNX Module LC-S.1 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung