Kodak D4000 Bedienungsanleitung

KODAK D4000 Duplex Photo Printer

November 2011

Photo Printer

User’s Guide for the Calibration Application

D4000Duplex Photo Printer

Rewind/Unload

Advance/Load

Eastman Kodak Company

Rochester, New York 14650

Kodak and XtraLife are trademarks of Eastman Kodak Company.

Portions of this software may contain intellectual property owned

or licensed by X-Rite, Incorporated, or one of its affiliates.

P/N 4J7914

November 2011 iii

Table of Contents

1 Getting Started

About the Printer Calibration Application ................................................................................................ 1-1

System Requirements.....................................................................................................................................1-2

Additional Information for Using an X-RITE i1PRO Device...................................................................1-2

Installing the Calibration Application.........................................................................................................1-3

Uninstalling the Calibration Application .................................................................................................. 1-4

WINDOWS XP Operating Systems ....................................................................................................1-4

WINDOWS 7 Operating Systems ....................................................................................................... 1-4

2 Starting the Calibration Application

Starting the Application from the Printer Driver .....................................................................................2-1

Starting the Application from the Desktop..............................................................................................2-2

3 Using the Calibration Application

Using the Visual Calibration Mode.............................................................................................................3-1

Using the Visual Calibration Mode for Simplex Printers ................................................................3-1

Using the Visual Calibration Mode for the KODAK D4000 Duplex Photo Printer ................3-3

Using the Instrumented Calibration Mode ..............................................................................................3-5

Using the Instrumented Calibration Mode for Simplex Printers..................................................3-5

Using the Instrumented Calibration Mode for Duplex Printers ...................................................3-7

4 Troubleshooting

Error Messages ............................................................................................................................................... 4-1

Launching the Calibration Application from the Printer Driver ................................................... 4-1

Calibration Errors ..................................................................................................................................... 4-1

Instrumented Calibration Errors...........................................................................................................4-2

Non-recoverable Errors ..........................................................................................................................4-2

November 2011 1-1

Getting Started

Welcome to the KODAK Photo Printer Calibration Application for

WINDOWS, a tool for calibrating KODAK Thermal Printers using

visual or instrumented calibration techniques.

The following KODAK Printer models are supported by the

calibration application:

• KODAK D4000Duplex Photo Printer

• KODAK 8810 Photo Printer

• KODAK Photo Printer 8800/9810

• KODAK 7000/7010/7015 Photo Printer

• KODAK Photo Printer 6800/6850

• KODAK Photo Printer 605

NOTE: Instrumented calibration is not supported with the

KODAK Photo Printer 6800/6850 and the KODAK Photo

Printer 605.

To use the instrumented calibration capability of the application,

you must have an X-RITE i1PRO spectrophotometer and the latest

i1PRO device driver software from X-RITE. If you have an X-Rite

i1Pro device, “Additional Information for Using an X-RITE i1PRO

Device” on page 1-2.

About the Printer Calibration Application

The KODAK Photo Printer Calibration Application (Calibration

Application) lets your Kodak printer produce the best possible

color. Calibration adjusts the response of the printer so that a

specific data input value yields a specific color density output.

The printer is shipped with default factory calibration settings.

You can set up your printer and print right away without having to

calibrate the printer. However, if you are dissatisfied with the color

of your prints, you should calibrate your printer.

1-2 November 2011

Getting Started

System Requirements

You must have the following:

The minimum requirement is the system configuration that

MICROSOFT requires for use with WINDOWS XP or

WINDOWS 7.

NOTE: 64-bit Intel Itanium-based systems are not supported.

The Calibration Application requires:

• a functional USB 2.0 port to communicate with the printer.

NOTE: If your equipment only supports the USB 1.1 protocol, data

communication to the printer is slower and may affect

calibration performance.

• .NET FRAMEWORK 4 from MICROSOFT to be installed on

your computer prior to installing the Calibration Application.

NOTE: If .NET FRAMEWORK 4 is not installed on your system,

the Calibration Application installer provides the

opportunity to download and install it before proceeding

with the installation of the Calibration Application. To

download .NET FRAMEWORK 4, you must be connected

to the internet. If you do not install .NET FRAMEWORK 4

when prompted, the calibration installation will not be

completed.

Additional Information for Using an X-RITE i1PRO Device

The X-RITE i1PRO uses software components that belong to the

X-RITE Corporation. Users should ensure that they have the most

up to date software for their i1PRO devices by contacting X-RITE

Corporation for support.

The X-RITE i1PRO device does not have a sound generator. The

i1PRO uses sound produced by the system board or sound card of

your computer. At the time of the release of the KODAK Photo

Printer Calibration Application, the X-RITE i1PRO device drivers

did not support sound on 64-bit WINDOWS Operating Systems.

Operating System Minimum Service Pack

WINDOWS XP Home SP3

WINDOWS XP Professional SP3

WINDOWS XP Professional

(x64 Edition)

SP2

WINDOWS 7 N/A

WINDOWS 7 (x64) N/A

Getting Started

November 2011 1-3

If your computer does not have a sound card and/or speakers, or

you are running a 64-bit Operating System, when you are

prompted to 'wait for the beep' during the instrumented

calibration:

1. Wait for the light below the reading probe of the X-RITE i1PRO

device to illuminate.

2. Hold the button for 3 seconds and then begin scanning the

strip on the calibration target.

IMPORTANT: If you try to scan a strip before the lamp has

stabilized, an error appears indicating an incorrect

number of patches were read. If this error occurs,

re-scan the strip after holding the button for 3

seconds prior to starting the scan.

Installing the Calibration Application

IMPORTANT: Before installing the software:

• Have .NET FRAMEWORK 4 installed.

• Have “Administrator” privileges.

If your system has an older version of calibration software

(KODAK Visual Printer Calibration Utility) installed, the installer

configures the Visual Calibration Utility to launch the new

Calibration Application.

1. Go to www.kodak.com/go/ enter your printer model number

For example: www.kodak.com/go/D4000

NOTE: Valid printer models are: D4000, 8810, 8800, 7000,

7010, 7015, 6800, 6850, and 605

2. Select the Standalone Printer tab.

3. Select the Technical Resources link for your printer model and

download the KODAK Photo Printer Calibration Application

for WINDOWS.

4. Locate the file that you downloaded to your hard drive and

double-click the file.

5. When the WinZip Self-Extractor screen appears, browse to a

folder location that is easy to access, such as your computer's

desktop. Click Unzip.

An Installer folder is created containing all of the files.

6. Double-click the Installer folder.

7. Double-click the setup.exe file.

NOTE: The installer checks to see if you have .NET FRAMEWORK

4 installed. If it is not installed, you are prompted to

download it from the MICROSOFT Web site and install it.

When the .NET FRAMEWORK 4 installation is complete,

you return to the Calibration Application installer.

1-4 November 2011

Getting Started

8. Follow the on-screen instructions to install the Calibration

Application.

NOTE: With some WINDOWS Operating Systems, a system

restart is required after installing .NET. If a restart is

required, the calibration application installer prompts you

to restart your system at the end of the installation of both

.NET and the Calibration Application.

Uninstalling the Calibration Application

To remove the calibration application software from your

computer, you must have “Administrator” privileges.

WINDOWS XP Operating Systems

1. From the Control Panel, open Add or Remove Programs.

2. Select “Kodak Photo Printer Calibration Application.”

3. Click Remove.

4. Click Ye s at the message prompt.

WINDOWS 7 Operating Systems

1. From the Control Panel, click Programs and Features.

2. Select “Kodak Photo Printer Calibration Application.”

3. Click Uninstall.

4. Click Ye s at the message prompt.

November 2011 2-1

Starting the Calibration Application

Starting the Application from the Printer Driver

1. For your operating system, do the following:

2. Click the KODAK Photo Printer that you would like to

calibrate.

3. Select Printer Properties.

4. Select the Printer Calibration tab.

5. Click Launch Calibration

The KODAK Photo Printer Calibration dialog box opens. The

name of the printer and the paper installed appear in the

upper section of the dialog box.

WINDOWS XP WINDOWS 7

Select Start > Printers and

Faxes.

Select Start > Control Panel >

Devices and Printers.

2-2 November 2011

Starting the Calibration Application

Starting the Application from the Desktop

You can launch the application from the desktop in one of two

ways:

• Double-click the shortcut for the Photo Printer Calibration

Application.

• Select Start>Programs>KODAK Photo Printer> Calibration

Application.

The KODAK Photo Printer Calibration Application dialog box

opens. The name of the printer and the paper installed appear

in the upper section of the dialog box.

Andere Handbücher für D4000

Inhaltsverzeichnis

Andere Kodak Drucker Handbücher

Kodak

Kodak 9810 - PRINTING IMAGES FROM PHOTOSHOP 7 AND... Bedienungsanleitung

Kodak

Kodak ESP 7200 Series Bedienungsanleitung

Kodak

Kodak Magnus VLF Q2400 Bedienungsanleitung

Kodak

Kodak ESP7200 - AUTRE Bedienungsanleitung

Kodak

Kodak NOVAJET 750 Einrichtungshandbuch

Kodak

Kodak Verite JF120UB Series Bedienungsanleitung

Kodak

Kodak Apex 7015 Bedienungsanleitung

Kodak

Kodak Printer Bedienungsanleitung

Kodak

Kodak VERITE CRAFT 6 Service-Handbuch

Kodak

Kodak Diconix 180si Bedienungsanleitung

Kodak

Kodak Smile Bedienungsanleitung

Kodak

Kodak D4600 Bedienungsanleitung

Kodak

Kodak verite 55 plus Technisches Datenblatt

Kodak

Kodak Mini Bedienungsanleitung

Kodak

Kodak 4800 Series Bedienungsanleitung

Kodak

Kodak 8650R THERMAL PRINTER Handbuch

Kodak

Kodak dryview 8300 Bedienungsanleitung

Kodak

Kodak EasyShare G600 Bedienungsanleitung

Kodak

Kodak XLS 8400 PS Bedienungsanleitung

Kodak

Kodak 9810 - PRINTING IMAGES FROM PHOTOSHOP 7 AND... Bedienungsanleitung

Kodak

Kodak Versamark DS9100 Leitfaden

Kodak

Kodak DryView 8150 Bedienungsanleitung

Kodak

Kodak NexPress 2500 Installationsanleitung

Kodak

Kodak EasyShare Photo Printer 500 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung