Kodak EKTAGRAPHIC III Abmessungen
KODAK EKTAGRAPHIC III
AFT Projector
PRODUCT DESCRIPTION
Congratulations on the purchase of your KODAK EKTAGRAPHIC III AFT Projector.
Please review this product sheet and the important maintenance instructions enclosed.
The KODAK EKTAGRAPHIC III AFT Projector is a standard KODAK EKTAGRAPHIC III
A Projector with fade and timer controls added. This projector was specifically designed
for cinema applications and therefore does not include a slide tray, lamp, lens, user manual, or
remote control.
FADE and VIEW controls
There are three controls for the special features of the AFT Projector. They are located under
the projector handle.
1. Automatic AFT mode (ON / OFF)
When this switch is ON ( I ), slides will advance automatically using the VIEW and
FADE times selected.
2. VIEW adjustment screw
Allows you to select the amount of time the slide is displayed on the screen, from
5 to 15 seconds.
3. FADE adjustment screw
Allows selection of the time it takes to fade up and down between slides, from 0.5
to 4 seconds.
NOTE: The operation will sequence as follows: fade up, change slide, fade down.
Selection of 0.5 second, for example, will fade up 0.5 seconds, change slide
1 second and fade down 0.5 seconds for a total of 2 seconds per slide change.
Important Safety Instructions
IMPORTANT:
Your KODAK EKTAGRAPHIC III AFT Projector is supplied with a 3-wire grounding
power cord to comply with UL122 and CSA222 Safety Electronics Standards.
We urge you to provide a permanent, properly installed 3-wire receptacle as the source
of power for this projector. Your projector is designed to operate with 110 to 125 volts,
60 Hz current only. Incorrect voltage could cause the projector to malfunction. Inputs in
excess of
125 volts will adversely affect lamp life.
When using your projector, always follow these basic safety precautions:
1. Read and understand all instructions before using this equipment.
2. Operate this projector with 110-125 volt 60 Hz current only. Incorrect voltage can
cause projector malfunction.
3. Close supervision is necessary when any appliance is used by or near children,
or others who may not understand the need for these precautions. Do not leave
the projector unattended during use.
4. Be careful not to touch hot parts. For lamp replacement, allow the module to
cool before touching the lamp and the surrounding area. Do not place the lamp
module on heat-sensitive surfaces.
5. Do not operate your projector if the power cord is damaged or if the projector
has been dropped or damaged.
6. Position the cord so that it is not tripped over. pulled, or placed in contact with
hot surfaces.
7. If an extension cord is necessary, use a cord with a current rating at least equal
to that of the projector. Cords rated for less amperage than the projector may
overheat.
8. Always unplug the projector from the electrical outlet before cleaning and
servicing and when not in use.
9. Allow the projector to cool before storing.
10. Do not immerse this equipment in water or other liquids.
11. Do not disassemble this projector. Use a qualified service technician when
service or repair is required. Incorrect reassemble can cause electric shock the
next time the projector is used.
12. Use only safety electrical low-voltage (SELV) devices.
13. The use of an accessory attachment not recommended by the manufacturer
may increase the risk of damage.
14. Keep the airflow vents unobstructed.
Troubleshooting Guide
PROBLEM CAUSE CORRECTION
Projector does not operate
No illumination on screen with
slide in projector gate
Slide not in proper focus on
screen
Uneven edge-to-edge focus
Autofocus motor runs
continuously
Slide fails to drop into projection
position
Uneven illumination on screen
Projector won’t cycle to next slide
Program does not start with the
correct slide
No power to projector
Power switch on Off or Fan
Lamp burned out
Lamp not sealed in socket
Slide itself not sharp
First slide in tray not properly
focused
Slide in different type of mount
from others
Projection lens installed improperly
Slide itself is not sharp
Curved-field lens used with glass,
plastic, or non-embossed mounts
Curved field lens used for rear
projection
Multi-aperture slides or matte-
surface write-on slides in tray
Tray base plate not properly
indexed
Tray not properly positioned on
projector
Slide mount warped or frayed at
corners
Projector not level or tilted too high
Projection lamp not fully seated
Condenser lens not installed or not
positioned properly in mount
Slide mount not seated properly in
projector gate
Tray not properly positioned
Slide or foreign object stuck in gate
Tray number is not aligned with the
raised index mark.
Plug power cord into suitable
electrical outlet. Set power switch
to LAMP.
Set switch to LAMP.
Install new lamp or lamp module.
Check lamp.
Examine slide for proper focus.
Focus center of first slide manually.
Focus manually.
Be sure the lens gear teeth on the
lens barrel line up with the notch on
the projector.
Examine slide.
Try a flat-field lens.
Use a flat-field lens.
Turn off autofocus.
Rotate the tray base plate until it
locks into position.
Reposition tray on projector.
Straighten mount or remount slide.
Set projector on a stand equal with
center of screen.
Check lamp.
Check condenser lens.
Check slide position and slide-
mount condition.
Reposition tray.
Remove foreign object from gate.
Reposition tray.
Warranty
Kodak warrants this KODAK EKTAGRAPHIC Slide Projector to function properly for four
years from the date of purchase.
If this KODAK EKTAGRAPHIC Slide Projector does not function properly within the
warranty period, upon submission of dated proof of purchase, Kodak will repair it without
charge, except for worn-out projector lamps. If Kodak is unable to repair the projector,
the option of replacement or refund of the purchase price will be available.
See an audiovisual products dealer for the KODAK EKTAGRAPHIC III AFT Slide
projector’s warranty coverage.
Limitations
This warranty does not cover circumstances beyond Kodak’s control, projector lamps, or
problems caused by failure to follow the care and operating instructions in the manual.
Any modification to the original design of this projector nullifies this warranty.
Warranty service will not be provided without dated proof of purchase.
Kodak makes on other express warranty for this product. Repair or replacement
is Kodak’s only obligation. Kodak will not be responsible for any consequential or
incidental damages resulting from the sale or use of this projector, regardless of
the cause of such damages.
Your Rights Under State Law
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights that vary from state to
state.
How To Obtain Service Assistance
To obtain service or assistance in using your KODAK EKTAGRAPHIC Slide Projector,
see an audiovisual products dealer in your area. If one is not available, call the Kodak
Information Center at 1-800-242-2424, Monday through Friday, 8 a.m. to 7 p.m. Eastern
time. In Canada, call 1-800-465-6325, Monday through Friday, 8:30 a.m. to 5 p.m.
Eastern time. Or call Kodak in your country.
Part No. 2H2270 New 2/98. Minor revision 7/99
Printed in U.S.A.
Kodak and Ektagraphic are trademarks.
www.kodak.com/go/projectors
Andere Handbücher für EKTAGRAPHIC III
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Kodak Projektor Handbücher
Kodak
Kodak CAROUSEL S-AV2020 Bedienungsanleitung
Kodak
Kodak Carousel S-AV 2010 Bedienungsanleitung
Kodak
Kodak Pocket Pico Projector Bedienungsanleitung
Kodak
Kodak Pageant Bedienungsanleitung
Kodak
Kodak EKTAPRO 7010 Betriebsanleitung
Kodak
Kodak FS-10-N Fehlerbehebungshandbuch
Kodak
Kodak LUMA 350 Bedienungsanleitung
Kodak
Kodak LUMA 350 Bedienungsanleitung
Kodak
Kodak Ektalite 1000 Bedienungsanleitung
Kodak
Kodak DP1100 - Digital Projector Bedienungsanleitung
Kodak
Kodak EKTAGRAPHIC 220 Bedienungsanleitung
Kodak
Kodak PAGEANT 250S Bedienungsanleitung
Kodak
Kodak Carousel 760 Bedienungsanleitung
Kodak
Kodak LUMA 150 Bedienungsanleitung
Kodak
Kodak EKTAPRO Bedienungsanleitung
Kodak
Kodak Carousel S-AV 2050 Betriebsanleitung
Kodak
Kodak EKTALITE Bedienungsanleitung
Kodak
Kodak V600 Bedienungsanleitung
Kodak
Kodak FLIK X7 Bedienungsanleitung
Kodak
Kodak iSow 1000 Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
