Kodak Ektapro 3020 Bedienungsanleitung

KODAK

EKTAPRO

3020

4020

5020

7020

9020

Slide Projector

Bedienungsanleitung

Instruction Manual

Mode d’emploi

Manual de Instrucciones

Istruzioni per l’uso

Projector-Features

140

Using the instruction manual

1 Slide change buttons (forwards; backwards)

2 Focusing buttons

3 Standby button

4 Lamp economy switch and High Light

(EKTAPRO 7020, 9020)

5 Fan(airinlet)

6 Interval Timer (EKTAPRO 5020, 9020)

7 Autofocus - on/off switch

(EKTAPRO 5020, 9020)

8 Switch for slide tray zeroing on/off

(EKTAPRO 9020)

 9Centre position indicator of lens mount

10 Tray setting switch 80/140

11 Focusing knob for gear rack lenses

12 Retractable handle

13 Height adjustment foot

14 Slide tray lock

15 Slide tray transport ring

16 Slide gate

17 Slide tray release (140) and lever for slide tray

positioning(80)

18 Operation indicator (LED) and Standby indicator

(EKTAPRO 7020, 9020)

19 Air exhaust

20 Lampmodule

21 P-Bus in (RS232) (EKTAPRO 4020; 5020; 7020, 9020)

22 P-Bus out (RS232) (EKTAPRO 7020, 9020)

23 ADDRESS Switch (EKTAPRO 7020, 9020)

24 Zero positioning indicator and Line up

(EKTAPRO 7020, 9020)

25 Remote control socket

26 Lamp failure indicator (L1, L2) (EKTAPRO 4020; 5020; 7020,

9020) and High Light indicator(EKTAPRO 7020, 9020)

27 Tray positioning index mark

28 Lampmodulerelease

29 Fuse holder (secondary circuit)

30 Voltageindicator

31 Fuselinkcompartment(primarycircuit)

32 Fuse link

33 Fuse(primarycircuit)

34 Mains switch (electrical)

35 Module expansion slot (EKTAPRO 7020, 9020)

36 AC mains socket

Openthecoverflap.Hereyouwillfindillustrationsoftheprojector.

The figures have also been incorporated into the op-erating

instructionstoenablequick and exact identificationoftheindivid-

ual projector features.

&SEPARATEMANUAL

EKTAPRO7020and9020Projector

Theseprojectorshave a built-indissolver.This special feature and

its commands are laid down in a separate manual which you will

also find in the box.

Action arrow:

Referencearrow:

WARNINGSareframed.

Important SafetyPrecautions................22

Introduction.........................................23

Switching-on the projector....................24

Operation............................................27

Other projection modes........................30

Service.................................................32

Servicing.............................................33

Accessories.........................................35

Technical Data....................................36

Content

Important texts are highlighted

in grey.

ElectricalApprovals

TheKODAKEKTAPRO3020/4020/5020/7020/9020SlideProjec-

torcomplies with InternationalSafety requirements andbears the

followingsafety marks:

UL(Underwriter Laboratories Inc.)

 CSA (Canadian Standards Association)

VDE(VerbandDeutscherElektrotechniker)

CEConformityMark

ToshowcompliancewithEMV-Directive89/336/EECandproduct

safety requirements, the slide projector bears the CE mark.

EKTAPRO 3020

In case of extreme mains disturbances problems with lamp flashing and/or

jamming may occur. In this case please switch the projector off and on again!

In case of a jam, please refer also to Possible problems during operation as

written in the manual on page 34. (Please keep the tray position in mind

before switching on the projector. With the random access function of the

IR remote control or the rapid search via the reverse transport button you

will easily come back to this position.)

EKTAPRO 4020, 5020, 7020, 9020

The projector is correspondingly programmed to prevent it from becoming

uncontrollable in the case of severe mains disturbances. Should such

disturbances occur, the projector resets itself, i.e. it brings the tray into zero

position and resynchronises itself. It is then fully operative again and ready

for use.

Radiointerference:

EECdirective89/336

Australia standards AS 1044

RFS49ISSUESJuly1989

VCCIRegulationsNov. 1987 Class2

Part 15 of FCC Rules Subpart J Class B

CanadianDOCC108,8-M1983Class B

Note: This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus set out in the Radio Interference regulations

of the Canadian Department of Communications.

Note: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/TV technican for help.

Electrical Approvals and

Conformity Mark

english

Important Safety Precautions

When using your equipment, basic safety precautions should

always be followed, including the following:

1. Read and understand all instructions before using.

2. Always use the correct voltage, as described on page 24.

Incorrect voltage can lead to malfunctions in the projector.

3. Close supervision is necessary when any appliance is used by

or near children, or others who may not understand the need for

the following precautions. Do not leave the projector unattend-

ed while in use.

4. Care must be taken as burns can occur from touching hot

parts. For lamp replacement let the module cool down before

touching the lamp and the surrounding area. Do not place the

lampmodule on heat sensitive surfaces (s. p. 32).

5. Do not operate projector with a damaged cord or if the

projector has been dropped or damaged - until it has been

examined by a qualified service technician.

6. Position the cord so that it will not be tripped over, pulled, or

placed in contact with hot surfaces.

7. Ifanextension cord is necessary, a cord with a current rating

at least equal to that of the projector should be used. Cords rated

for less amperage than the projector may overheat.

8. Always unplug the projector from the mains before cleaning

andservicing(e.g.lampreplacement)andwhennotinuse.Never

pull cord to plug from outlet. Grasp plug and pull to disconnect.

9. Let the projector cool completely before putting away.

10. To reduce the risk of electric shock, do not immerse this

projector in water or other liquids.

11. To reduce the risk of electric shock, do not disassemble this

projector, but take it to a qualified service technican if service

or repair work is required. Incorrect reassembly can cause an

electric shock when the projector is used subsequently.

12.Theuse ofan accessory attachment not recommendedbythe

manufacturer may cause a risk of fire, electric shock, or injury

to persons. Only devices with safety-low voltage (SELV) are

allowed to be connected.

13. Connect this projector to a grounded outlet.

14. Keep air inlet (5) and air outlet (19) free from obstruction.

SAV E THESE INSTRUCTIONS!

Introduction

Welcome to the world of the KODAK EKTAPRO Slide

Projectors. You are, with your EKTAPRO Slide Pro-

jector, holding one of the newest generation KODAK

projectors. It will certainly help you meet your current and future

35 mm slide projection challenges.

Afewbenefits of yournew KODAK EKTAPROSlideProjector are

listed below. We wish you much pleasure in presenting with this

projector.

-Highest precision

All functions are continually monitored and controlled with the

highest precision by the built-in microprocessor. This, for exam-

ple, guarantees that the slide change time will always be kept,

independent of the voltage used.

- Optical quality

All important structural elements for the optical equipment such

as the slide gate and base for the lens mount housing are in die-

cast, and adjustment problems are, thereby, minimized.

- Communication

ConnectiontothePCworld! Youareabletocommunicatewiththe

projector via a connected PC with the help of EKTAPRO P-COM

Protocol-theprojectorscommunicationslanguage. Theinterface

is called P-Bus.

Totalintegrationof the projector intothemultimedia scene isnow

realizable.

- Convenience

Working with EKTAPRO Projectors means presenting with the

greatest of ease: Standby, no-slide-no-light, integrated dissolver

and random access are but a few of the features.

- Flexibility

The modular design, lamp module and the module expansion slot

allow your projector to be constantly adapted to today and future

developments.

- Up-to-date

Due to environmental and recycling reasons EKTAPRO Slide

Projectors are not varnished. This is visible on the shade-differ-

ences of the housing.

. Connectyour EKTAPRO Slide Projector

to themains withthemainslead. (UK users

note: A suitable fused 13A plug must be

fitted. See instructions on cable!)

.Turn on the mains switch (34).

The projector is switched on and ready for

use.TheredLED(18)ison;lampandfanare

switched off. I.e. the projector stays in a

"silent" mode. With any strike on a key

(suchastransport,standby,..)lampand fan

will be switched on.

Note:

If a problem on the slide change is

detected, the red LED (18) (operation

indicator) will start to blink and the

projector can no longer be operated

(see Trouble Shooting Guide, page 34).

Switching-on the projector

EKTAPRO Slide Projectors will be exported throughout the world to countries with

differing mains voltages. The projectors are already set during manufacture to a fixed

mains voltage.

Shipments to countries with 100 or 120 V mains will be equipped with a 4 A slow blow/

250 V fuse. A spare fuse for replacement is also supplied.

Shipments to countries with 220, 230 or 240 V mains will be equipped with a T 2A L/

250 V fuse. A spare fuse for replacement is also supplied.

Before you switch on your projector ensure that the voltage is correctly adjusted! An

incorrectly adjusted mains voltage can damage the projector! The voltage indicator

(30) must show your country´s actual mains voltage!

Setting of a different operation voltage

WARNING

For safety, the mains lead must be unplugged!

Important:

Ensure that the 100 and 120 V setting uses a different fuse to the 220 -240 V setting.

See text above!

1. Unlock the fuse link compartment (31) by using a screwdriver and pull

compartment out.

2. Push the fuse link (32) into the compartment so -

3. - that the applied voltage can be seen in the window (30) of the compartment.

.Push the loaded compartment (with mounting underneath) firmly into the

projector opening provided.

Check voltage setting

140

Tray setting

Round trays for both 80 slides and 140

slides can be used. The tray setting switch

(10) is set in the factory to accomodate the

80 tray. By using a small screwdriver, the

switchcanbebroughtintothe 140 position.

Caution

If the projector is not properly adjusted,

there will be transport problems!

You can only set the EKTAPRO 3020

before you switch on the projector!

Switching- on the

projector

Loading and installing the slide tray

Projectorsareofteninstalledonrackswhere

tray installation may be difficult and only

possible from the rear of the projector. In

this case the tray positioning index mark

(27) on the back of the projector is very

helpful: The tray is properly set when the

index mark aligns with the mark placed on

the tray (at slide no. 20 of the 80 slide tray

and at slide no. 35 on the 140 slide tray).

Traypositioning indexmark

1. Checkthatthe baseplate of theslidetray is locked

into zero-position and cannot be rotated.

2. Load the slides up-

side down for normal front

projection.

.Replace and lock the

cover to prevent damage

andsplittingincasethetray

is dropped or turned over.

3. Place the loaded tray into its zero

position on the projectors transport ring

(15). The cleft in the slide tray (zero posi-

tion) fits on to the notch of the transport

ring.

Note:

 To avoid annoying automatic refocus-

ing during presentation, damaged,

distorted or warped slides should not be

used as they may jam the projector`s

transport mechanism.

 A slide tray index (80 slides) for

copying can be found on page 86. This

is ideal for archiving and an index copy

can be made for each slide tray.

With the higher light ouput of the Extra

BrightLampModulethetemperatureinthe

slide gate rises. To enable a smooth oper-

ation following hints should be consid-

ered:

1. Use only light respectively light gray

slide mounts (e.g. Wess slide mounts).

Slide mounts with only one dark side or

blackside have tobe sorted inrespectively,

mounted with the side facing the lamp.

Please pay special attention when sorting

your slide mounts in rear projections:

Extra Bright Lamp

Module - Important Hints

2. Donotuse a lamp typeEXW/15h for the

projector (higher temperature - lamp not

availablefromKodak).

3. Consider the room temperature! It may

not exceed 35 degrees C!

4. High-Light-Mode (models 7010, 7020,

9010,9020):Slideprojection time per slide

may not exceed 1 minute!

Ifthesehints are notconsidered,

mountsmaydeform!

5. Glassmounted slides canproduce sweat

spots due to the high temperature in long

term projections. As soon as the slide has

warmed up these sweat spots disappear.

To reduce slide temperature (and light

output):

a) Install a heat-absorbing filter (see Ac-

cessories p. 35) or

b) Use the lamp economy switch, or

c) install a 200 h lamp (see Accessories p.

35)

Placethe projector on a firm,vibration free

base for stable and smooth operation.

For professional use we recommend the

specialprojectionracksavailablefromdeal-

ers. The projector may be elevated plus or

minus 30ofrom the horizontal along the

projectionaxis.

Note: Operating the projector at its

maximum angle setting may reduce the

average lamp life time!

Setting up the projector

Push the slide-forward button (1) to

project a slide.

Focusing the image

(manually)

Thepicture focus canbe altered atany time

during the projection by using the focus

buttons (2) on the projector or the corre-

sponding buttons on the remote control.

The first slide, at the beginning of every

projection, must be focused by turning the

knobfor gear rack lenses (11) or by turning

the spiral lens:

1. Slide positioning

Presslightlytheslideforwardbutton (1).

The first slide will move into the slide gate

and will be projected.

2. Movethelens mount tothemiddle

position

Repeatedly press the focus buttons (2)

until-

3. - the indicator pointer of the centre

position indicator (9) reaches the middle

position.

4. Focusing

a)withKODAK EKTAPRO Lensesor any

other gear rack lens:

- by turning the focusing knob (11)

b) with spiral lenses:

- by turning the lens by hand.

Line-up (EKTAPRO 4020, 5020, 7020, 9020)

Aligning the projectors i.e. fully fading up all projectors, in multivision operation is

difficult, since dissolve units often do not provide this kind of option.

With the Line-up feature you can turn the light of every projector on and off

independently. This means the projectors can be aligned or checked at any time.

Youcan only set the line-uponthe projector. (Theexternal controlling via P-Busis

rejectedduring setting. Withline-up standby will be alsoswitched off andtheshutter

will be opened):

Line-up on: Press both transport buttons on the projector simultaneously for at least

1 second. The lamp now lights up at maximum output and the zero position indicator

(greenLED,24)flashes.

Line-up off: Press the standby button (3).

Important! Proper ventilation is

required!

Check that the projector can draw-in

sufficient cool air and that warm air can

be freely expelled.

Keep air inlet (5) and air outlet (19)

free from obstruction!

Fitting the lens

Leveling the projector

Gear rack lenses:

Gear rack lenses (such as KODAK Slide

Projection FF Lenses) are pushed into the

lens mount housing. A slide tray index (80

slides)forcopyingcan be foundonpage86.

Thisisidealforarchivingandanindexcopy

can be made for each slide tray.

Spiral lenses:

Spiral grooved lenses are screwed clock-

wise (from front of the projector) into the

lens mount housing.

max.30º

.Turn the projector feet (13) to adjust the

height.

1. 2. 4.

Operation

EKTAPRO 5020 and

9020 Projector: Focusing

with the autofocus

1.Slide positioning

Presslightlytheslideforwardbutton (1).

The first slide will be moved into the slide

gate and will be projected.

2. Switch the autofocus (7) on

(Push button in).

3.Focusing

a) withKODAKEKTAPROlensesorother

gear rack lenses:

- by turning the focusing knob (11)

b) with spiral lenses:

- by turning the lens by hand

Overridefeature

You can, however, re-adjust the focus at

any time using the focus buttons (2). The

autofocusisre-activatedwiththenext slide

change.

Manual refocusing during projection is no

longer necessary as the built-in autofocus

devicewill automatically give the bestdef-

inition.

However, before you start, the first slide

has to be manually focused by turning the

knobfor gear rack lenses (11) or byturning

the spiral lens (the lens mount should be

about in middle position) :

I. Using the buttons on the projector or

remotecontrol*

Single Movement:

Press button (1)

forwards

backwards

Quick search and zero positioning:

Totransportthetrayquicklyineitherdirec-

tion, press and hold down the slide change

button-backwards (1) [ ] until the posi-

tion wanted is reached. The tray will, how-

ever,automaticallystopat0andwillremain

in this position. If you want to repeat the

search run, press the slide change button-

backwards again.

Please note

Your EKTAPRO Slide Projector can sense

when there is a slide in the gate. Only then

will the shutter open and the lamp achieve

its optimum brightness.

In exceptional case the feature can also be

switched off with the IR Remote Control

(does not apply for the EKTAPRO 3020).

To do this, enter the figures 555 and con-

firm with "*".

*There are three different remote controls avail-

able as accessories to your EKTAPRO Slide Pro-

jector. (Description of the most important fea-

tures under Accessories page 35):

II.Usingthebuilt-inintervaltimer(EKT-

APRO 5020 and 9020 Projectors)

The built-in timer (6) enables the projector

to automatically transport your slides.

Eleven time settings can be made:

Markedtimesettings:

1; 2; 3; 4; 5; 10; 30; 60 sec

Unmarkedinterimtimesettings:

8 sec

(timer position between 5 and 10 sec)

20 sec

(timer position between 10 and 30 sec)

45 sec

(timer position between 30 and 60 sec)

Slide changing

1. Setting the timer:

Turn the timer clockwise, to the right, until

the time required agrees with the indicator

ontheprojector. Thetimerisnowactivated

and the first picture will be projected after

expiration of the set time interval.

2. Switching the timer off:

Turn the timer to the OFF position.

Note: The slide transport button can be

pressed at any time to project the next

slide independently of the timer setting .

The preset time of the timer will not be

interrupted.

Andere Handbücher für Ektapro 3020

Dieses Handbuch passt für folgende Modelle

Andere Kodak Projektor Handbücher

Kodak

Kodak 960 Benutzerhandbuch

Kodak

Kodak NOVAJET 750 Bedienungsanleitung

Kodak

Kodak Carousel S-AV 2050 AF Bedienungsanleitung

Kodak

Kodak LUMA 450 Bedienungsanleitung

Kodak

Kodak Pocket Pico Projector Bedienungsanleitung

Kodak

Kodak PAGEANT 250S Bedienungsanleitung

Kodak

Kodak EKTALITE Bedienungsanleitung

Kodak

Kodak EKTAGRAPHIC Bedienungsanleitung

Kodak

Kodak FLIK X4 Bedienungsanleitung

Kodak

Kodak Model AFT Bedienungsanleitung

Kodak

Kodak DP900 - Digital Projector Bedienungsanleitung

Kodak

Kodak EKTAPRO 9020 CINE Bedienungsanleitung

Kodak

Kodak pagent 250s Bedienungsanleitung

Kodak

Kodak EKTAPRO 7010 Betriebsanleitung

Kodak

Kodak CAROUSEL S-AV2020 Bedienungsanleitung

Kodak

Kodak Pocket Pico Projector Bedienungsanleitung

Kodak

Kodak S-AV 1020 Bedienungsanleitung

Kodak

Kodak DP800 - Digital Projector Bedienungsanleitung

Kodak

Kodak 5600 - BC5601 Carousel Projector Bedienungsanleitung

Kodak

Kodak EKTAGRAPHIC AFT Bedienungsanleitung

Kodak

Kodak FLIK HD9 Bedienungsanleitung

Kodak

Kodak DP2900 - Digital Projector Bedienungsanleitung

Kodak

Kodak Luma 75 Bedienungsanleitung

Kodak

Kodak CAROUSEL BC5601 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung