Kohler K-10332 Bedienungsanleitung

Installation Guide

Lavatory Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page ″Français-1″

Español, página ″Español-1″

K-10332, K-10341

1048639-2-C

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

For new installations, install the faucet and drain to the lavatory

before installing the lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench

Plumbers Putty 1/8"

Hex Wrench

1048639-2-C 2 Kohler Co.

1. Install the Faucet and Lift Rod Holder

Install the Lift Rod Holder

IMPORTANT! The lift rod holder and lift rod must be installed

before the faucet. Once the faucet is installed, it would be difficult to

install the lift rod components without damaging the lift rod.

Apply plumbers putty or other sealant to the underside of the lift

rod holder ﬂange.

Insert the lift rod holder through the mounting hole.

Secure the lift rod holder with the mounting nut.

With a damp cloth, wipe any excess putty or sealant.

Insert the lift rod into the lift rod holder.

Assemble the Faucet

NOTE: If your faucet is already assembled, continue to ″Install the

Faucet.″

Remove the plug from the faucet body and the cap from the

spout. Discard the plug and cap.

Lift Rod

Faucet Body

Setscrew

Plug

Cap

Flange

Escutcheon

Threaded Stud

Washer

Washer Nuts

Coupling Nuts

Mounting Hole

Mounting Nut

Lift Rod Holder

Kohler Co. 3 1048639-2-C

Install the Faucet and Lift Rod Holder (cont.)

Insert the spout into the faucet body and press down ﬁrmly to

engage the seal.

Position the spout.

Using the provided setscrew and wrench, secure the spout to the

faucet body.

Install the Faucet

Clean the lavatory surface to remove any grease, oil, or debris.

Apply plumbers putty or other sealant to the underside of each

escutcheon according to the putty manufacturer’s instructions.

Slide an escutcheon over each of the threaded studs.

Insert the threaded studs through the mounting holes.

Slide a washer onto each of the threaded studs.

Thread a nut onto each threaded stud to secure the faucet to the

mounting surface. Securely wrench tighten the nuts.

With a damp cloth, wipe any excess putty or sealant from around

the escutcheons.

1048639-2-C 4 Kohler Co.

2. Install the Drain

Remove the plastic cap from the drain assembly.

Remove the stopper from the ﬂange.

Remove the ﬂange from the drain body.

Thread the body nut down the drain body.

Slide the seal down to the body nut.

From underneath the lavatory, insert the drain body through the

drain hole.

Apply plumbers putty to the underside of the ﬂange.

Thread the ﬂange onto the top of the drain body.

Thread the body nut up the drain body until the seal is

compressed against the underside of the lavatory.

Wipe away any excess plumbers putty from around the ﬂange.

Remove the rod nut from the drain body.

Remove the clip from the rod.

Body Nut

Stopper

Stopper Bolt

Plastic Cap

Lift Rod

Flange

Drain Body

Tailpiece

Seal

Rod

Clip

Rod Nut

Link

Thumbscrew

Kohler Co. 5 1048639-2-C

Install the Drain (cont.)

Insert the short end of the rod into the seal hole and under the

stopper. Loosely secure in place with the rod nut.

Push the rod down to open the drain.

Insert the stopper into the drain assembly.

Remove and adjust the stopper so it lifts approximately 3/8″(1

cm) when opened. To adjust, hold the stopper bolt and turn the

stopper counterclockwise to raise and clockwise to lower.

Reinstall the stopper.

For Vandal-Resistant Installations: Remove the rod nut. While

the stopper is in place, insert the end of the rod through the hole

in the stopper bolt. Secure the rod with the rod nut.

For All Other Installations: Tighten the rod nut to secure the rod.

Identify the best hole in the link to allow full operation of the rod

and the lift rod.

Align the link hole with the rod and slide the clip and the link

onto the rod with the thumbscrew facing the back of the lavatory.

To move the link to the proper position, squeeze the clip and

slide it along the rod.

Align the link with the faucet lift rod and push the lift rod

through the hole in the link. If required, loosen the thumbscrew

on the link.

Verify that the lift rod knob rests on the escutcheon when the

drain is in the full open position.

Tighten the thumbscrew to secure the lift rod position.

1048639-2-C 6 Kohler Co.

3. Supply Connections

If the lavatory is not installed, install it at this time according to

the lavatory manufacturer’s instructions.

Connect the faucet supply shanks to the supply lines with the

coupling nut. (Left is hot - right is cold.) Securely tighten the

coupling nuts.

Tighten all connections.

4. Installation Checkout

Connect the P-trap.

Make sure all connections are tight.

Remove the aerator by turning it counterclockwise.

Open the drain.

Turn on the main water supply and check for leaks. Adjust as

needed.

Open both hot and cold valves and run water through the spout

for about a minute to remove debris. Check for leaks.

Close the hot and cold valves.

Remove any debris from the aerator and reinstall.

Shank

Coupling

Nut

Supply

Tube

Supply

Stop

Kohler Co. 7 1048639-2-C

Guide d’installation

Robinet de lavabo

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de performance. Nos numéros de téléphone

et notre adresse du site internet sont au verso. Merci encore d’avoir

choisi la compagnie Kohler.

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Vériﬁer avec soin si les tubes d’évacuation et d’alimentation d’eau

sont endommagés.

Pour de nouvelles installations, installer le robinet et le drain au

lavabo avant d’installer celui-ci.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Clé à molette

Mastic de

plombier

Clé

hexagonale

de 1/8"

Kohler Co. Français-1 1048639-2-C

1. Installer le robinet et le support de la tige de levage

Installer le support de la tige de levage

IMPORTANT ! La tige de levage et le support doivent être installés

avant le robinet. Une fois le robinet installé, il sera difficile d’installer

les composants de la tige de levage sans endommagement.

Appliquer du mastic de plombier ou autre étanchéité sous la

bride du support de la tige de levage.

Insérer le support de la tige de levage à travers l’oriﬁce de

montage.

Sécuriser le support de la tige de levage avec l’écrou de montage.

Avec un chiffon humide, essuyer tout excès de mastic ou de

matériau d’étanchéité.

Insérer la tige de levage dans son support.

Assembler le robinet

REMARQUE : Si le robinet est déjà assemblé, continuer à ″Installer

le robinet″.

Tige de

levage

Corps du robinet

Bride

Applique

Montant fileté

Rondelle

Rondelle Écrous

Écrous de couplage

Trou de fixation

Écrou de montage

Support de

tige de levage

Vis de retenue

Bouchon

Capuchon

Kohler Co. Français-2 1048639-2-C

Installer le robinet et le support de la tige de levage (cont.)

Retirer le bouchon du corps du robinet et le capuchon du bec.

Jeter le bouchon et le capuchon.

Insérer le bec dans le corps du robinet et le presser fermement

pour engager le joint.

Positionner le bec.

En utilisant les vis de retenue fournies et la clé, sécuriser le bec

au corps du robinet.

Installer le robinet

Nettoyer la surface du lavabo pour éliminer toute graisse, huile

ou débris.

Appliquer du mastic de plombier ou autre matériau d’étanchéité

au-dessous de chaque applique selon les instructions du fabricant.

Glisser une applique sur chacun des montants ﬁletés.

Insérer les montants ﬁletés à travers les oriﬁces de montage.

Glisser une rondelle sur chacun des quatre montants ﬁletés.

Visser un écrou sur chaque montant ﬁleté pour sécuriser le

robinet à la surface de montage. Serrer les écrous à fond au

moyen de la clé à molette.

Avec un chiffon humide, essuyer tout excès de mastic ou de

matériau d’étanchéité autour des appliques.

1048639-2-C Français-3 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Badezimmerarmatur Handbücher

Kohler

Kohler SKYLINE K-22317T-FM-S Bedienungsanleitung

Kohler

Kohler Entertainment K-11930 Montageanleitung

Kohler

Kohler LOURE 98964A Bedienungsanleitung

Kohler

Kohler K-8298 Montageanleitung

Kohler

Kohler K-355 Bedienungsanleitung

Kohler

Kohler Jacob Delafon CONTRA E22T81-GA Bedienungsanleitung

Kohler

Kohler Converge K-R77634 Bedienungsanleitung

Kohler

Kohler K-6534 Bedienungsanleitung

Kohler

Kohler K-18564X Montageanleitung

Kohler

Kohler K-10044 Montageanleitung

Kohler

Kohler K-842-H2 Montageanleitung

Kohler

Kohler URBANITY 25717T-9 Bedienungsanleitung

Kohler

Kohler K-1098 Bedienungsanleitung

Kohler

Kohler K-2000 Montageanleitung

Kohler

Kohler Sterling 660SP Series Montageanleitung

Kohler

Kohler K-9702 Bedienungsanleitung

Kohler

Kohler K-45765 Series Montageanleitung

Kohler

Kohler K-10550 Bedienungsanleitung

Kohler

Kohler MasterShower K-8520 Bedienungsanleitung

Kohler

Kohler Bancroft K-2347 Bedienungsanleitung

Kohler

Kohler K-7605 Montageanleitung

Kohler

Kohler STERLING 7610 Series Bedienungsanleitung

Kohler

Kohler 11623 Bedienungsanleitung

Kohler

Kohler 11615 Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

baliv

baliv DUK-80.30 T Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung

GRE

GRE DSALC32W Bedienungsanleitung