Kohler K-1098 Bedienungsanleitung

Installation Guide

Bath/Shower Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-1098 K-1099

114542-2-BC

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard.

•The pressure-balanced valve will not compensate for changes in

the water supply temperature; adjust the maximum water

temperature setting of this pressure-balanced valve when such

changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this pressure-balanced valve

according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

114542-2-BC 2 Kohler Co.

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

IMPORTANT! This instruction provides installation information for

two faucet models. Be sure to follow the steps that apply to your

installation.

Please read all instructions before you begin.

Observe all local plumbing and building codes.

Shut off the main water supply.

The K-1099 uses two valves, one for the bath ﬁll, and another for

the shower. Pay special attention to this feature when planning

your site preparation.

Avoid excessive heat if you solder connections to prevent damage

to the ﬁtting.

Flush all piping thoroughly before installing the valve(s).

Do not force the handle(s) in any direction. To turn the valve off,

gently turn it to the ″Off″position.

For the K-1099, do not use any plastic pipe between the valve and

the spout.

Pipe

Wrench Adjustable

Wrench Strap

Wrench Hacksaw or Tubing Cutter

Propane

Torch

Solder

Hex

Wrench

Thread

Sealant

Plumbers

Putty

Assorted

Screwdrivers Thermometer

Kohler Co. 3 114542-2-BC

Before You Begin (cont.)

Do not connect a deck-mount spout, diverter, or handshower to

the spout outlet unless you cap the shower outlet on the valve.

Install a pipe or tube in a straight drop of 7” (17.8 cm) to 18”

(45.7 cm) with only one elbow between the valve and the

wall-mounted spout. Other types of installation may cause

unsatisfactory shower performance.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

114542-2-BC 4 Kohler Co.

1. Rough-In Dimensions

K-1098

48" (121.9 cm)

to Floor

(Shower Only)

1/2" Pipe

5-5/16"

(13.5 cm)

7-5/16"

(18.6 cm)

3" (7.6 cm) Max.

2-7/8"

(7.3 cm)

4-7/8" (12.4 cm)

1/2"

Cold

1/2" Hot

72" (182.9 cm) -

78" (198.1 cm) To

Floor (Typical)

2-1/4" (5.7 cm) Min.

1/2" Pipe

4" (10.2 cm)

Top of Rim 4"

(10.2 cm)

(20.3 cm)

1/2" Pipe

5-5/16"

(13.5 cm)

7-5/16"

(18.6 cm)

3" (7.6 cm) Max. 2-7/8"

(7.3 cm)

4-7/8" (12.4 cm)

1/2"

Cold

1/2" Hot

72" (182.9 cm) -

78" (198.1 cm) To

Floor (Typical)

2-1/4" (5.7 cm) Min. 1/2" Pipe

4" (10.2 cm)

Top of Rim 4"

(10.2 cm)

10"

(25.4 cm)

1/2" Pipe

K-1099

2-7/8"

(7.3 cm)

(10.2 cm)

4" (10.2 cm)

6" (15.2 cm) D.

1/2" Cold

1/2" Hot

Kohler Co. 5 114542-2-BC

2. Install the Support Framing

K-1098 Only

Determine the installation location of the valve, showerhead, and

spout.

Install the support framing as required.

K-1099 Only

Determine the installation location of the valve, showerhead, and

spout.

Install the support framing as required.

72" (182.9 cm) -

78" (198.1 cm)

To Floor (Typical)

4" (10.2 cm)

10" (25.4 cm)

48" (121.9 cm)

to Floor

(Shower Only)

72" (182.9 cm) -

78" (198.1 cm)

To Floor (Typical)

4" (10.2 cm)

10" (25.4 cm)

114542-2-BC 6 Kohler Co.

3. Installing the Yoke

All Installations

Install elbows and adapters (if used) onto 1/2″copper tubing or

1/2″pipe of proper length.

Connect the piping to the bath yoke outlet.

Secure the tubing to the framing.

Install a temporary 1/2″nipple into the bath ell, and if applicable,

the shower ell. The nipple should extend at least 2″(5.1 cm)

beyond the ﬁnished wall.

Model K-1099

Apply thread sealant to the plug threads and install the plug in

the shower outlet.

Elbow

Adapters

1/2" Copper

Tubing

1/2" Copper

Tubing

Temporary

Nipple

Temporary

Nipple

K-1098

Shower

Outlet

1/2"

Adapter

Solder

Direct

1/2" Copper

or Pipe

Temporary

Nipple

Bath

Outlet

Bath Ell

Plug

K-1099

Kohler Co. 7 114542-2-BC

4. Install the Yoke - Ceiling Installations

IMPORTANT! Perform these steps for ceiling installations only.

The faucet ﬁtting is factory assembled speciﬁcally for hot and

cold water supplies from the ﬂoor.

If installing the faucet for ceiling supplies, turn the yoke over so

the supplies connect from the top.

Remove the aspirator with a 3/8” hex wrench.

For the K-1098, reinstall the aspirator at the top of the yoke. Do

not overtighten. For the K-1099, discard the aspirator.

Reversing the yoke for ceiling supplies reverses the direction the

lever handles close.

For proper operation, reverse the ceramic valves.

Open the valve before removing it.

Tighten the valves securely.

If you are installing K-1099, proceed to the next section.

Aspirator

Hot

Cold

Valve Unit

Ceiling

Supplies

Thread

Protector

114542-2-BC 8 Kohler Co.

5. Installing the Valve - K-1099

CAUTION: Risk of product damage. The valve body contains

plastic components. Remove the stop nut and stem assembly,

valve cap, and pressure balancing unit before you apply

soldering heat to the valve body.

IMPORTANT! Use thread sealant on all threaded connections.

Carefully remove the stop nut and stem assembly, valve cap,

collar, and pressure balancing unit before you apply soldering

heat to the valve body.

Rotate the valve fully counterclockwise.

If the valve has stops, rotate both stop adjustments fully

counterclockwise.

Install elbows and adapters (if used) to 1/2″copper tubing or

1/2″pipe of proper length.

Secure the tubing to the framing.

Install a temporary 1/2″nipple into the shower ell to extend at

least 2″(5.1 cm) beyond the ﬁnished wall.

Use thread sealant, and install a pipe cap on the bath outlet.

Stem

Assembly Stop Nut

Valve

Cap

Valve

Body

Pressure

Balancing Unit

Plaster

Guard

Screws

Collar

Less StopsWith Stops

Cap

Bath Outlet

Hot Side

Shower Outlet

Shower Ell 1/2" Copper

or Pipe

1/2" Adapter or

Solder Direct

Kohler Co. 9 114542-2-BC

6. Complete Valve Installation - K-1099

CAUTION: Risk of product damage. The valve body contains

plastic components. Remove the stop nut and stem assembly,

valve cap, and pressure balancing unit before you apply

soldering heat to the valve body.

NOTE: If the valve is to be installed in a two valve, back-to- back

conﬁguration, proceed to the ″Back-to-Back Installation″section.

IMPORTANT! Use thread sealant on all threaded connections.

Connect the water supplies to the valve body using elbows, 1/2”

copper tubing or pipe, and adapters (if needed).

Secure the piping to the framing.

Temporarily install 1/2” nipples to the bath and shower elbows

so they will extend at least 2” (5.1 cm) beyond the ﬁnished wall.

If you removed the inner valve components for soldering,

carefully reinstall them now.

1/2"

Copper

or Pipe

1/2"

Elbow

Temporary

Nipple

Temporary

Nipple

Valve

Body

Hot

Supply

Stem

Assembly

Cold

Supply

Pressure

Balancing

Unit

Collar

Screws

Valve Cap

Stop Nut

1/2"

Adapter

or Solder

Direct

114542-2-BC 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Badezimmerarmatur Handbücher

Kohler

Kohler 1195777-W2-A Bedienungsanleitung

Kohler

Kohler K-12100 Bedienungsanleitung

Kohler

Kohler K-18751 Montageanleitung

Kohler

Kohler JULY 72901T Bedienungsanleitung

Kohler

Kohler STRAYT K-72866T-NW-CP Bedienungsanleitung

Kohler

Kohler K-1010 Montageanleitung

Kohler

Kohler K-8247 Montageanleitung

Kohler

Kohler Mira Logic Bedienungsanleitung

Kohler

Kohler K-2746T-1/8 Bedienungsanleitung

Kohler

Kohler K-18564X Montageanleitung

Kohler

Kohler K-8002 Montageanleitung

Kohler

Kohler 45532X-4 Bedienungsanleitung

Kohler

Kohler K-T14420 Bedienungsanleitung

Kohler

Kohler K-9674 Bedienungsanleitung

Kohler

Kohler K-1110 Bedienungsanleitung

Kohler

Kohler K-T944-4 Montageanleitung

Kohler

Kohler Purist Upgrade K-99170T Bedienungsanleitung

Kohler

Kohler K-9035 Montageanleitung

Kohler

Kohler K-14518 Bedienungsanleitung

Kohler

Kohler POPLIN K-75881T Bedienungsanleitung

Kohler

Kohler CITRUS 27794T Bedienungsanleitung

Kohler

Kohler K-10044 Montageanleitung

Kohler

Kohler K-6525 Bedienungsanleitung

Kohler

Kohler Awaken R72421T Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

baliv

baliv DUK-80.30 T Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung

GRE

GRE DSALC32W Bedienungsanleitung