Kohler 1297608-2 Bedienungsanleitung
IMPORTANT INSTRUCTIONS
WARNING: When using electrical products, basic precautions should always be followed, including the
following:
DANGER: Risk of electric shock. Connect only to a circuit protected by a Ground-Fault Circuit-Interrupter
(GFCI)*.
WARNING: Risk of electric shock. A qualied electrician should route all electrical wiring.
WARNING: Risk of electric shock. Disconnect the power before servicing.
WARNING: Risk of electric shock. Do not operate electrical-powered auxiliary audio devices near water.
WARNING: Risk of injury or property damage. Read all instructions thoroughly before beginning installation.
NOTICE: Follow all plumbing, building, and electrical codes. In Canada, install this unit in accordance with the
Canadian Electrical Code, Part 1.
NOTICE: Grounding is required. The unit should be installed and grounded by a qualified service representative.
NOTICE: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified
agent in order to avoid a hazard.
NOTICE: Provide a minimum 6" (152 mm) of air space around the control amplifier to ensure adequate air flow.
Install to permit access for servicing.
*Outside North America, this may be known as a Residual Current Device (RCD).
Tools and Materials
Breathing Protection Tin Snips 100% Silicone Sealant
Plus:
•Woodworking Tools and Materials
•Drop Cloth
1297608-2-E2 Kohler Co.
• Construction Adhesive (Optional)
• Cement* or Mortar (Optional)
• 2x4s
• Plastic Film (Optional)
• 1/8" (3 mm) Spacer
* Do not use gypsum cement.
Before You Begin
IMPORTANT! Due to BLUETOOTH® signal overlap, installations of multiple baths within 50 ft (15.2 m) of each other
will require special order product. Contact your dealer, showroom, or sales representative for ordering assistance.
NOTICE: Provide adequate oor support. Note the model number on the back of the bath, then visit the product page at
kohler.com for more information.
NOTICE: Do not support the load weight of the bath by the rim. Plan to shim under the bath as needed when leveling the
bath.
NOTICE: Verify adequate support if installing a rim- or deck-mount faucet. Large faucets that may be inadvertently used
as a means of support are not safe for this installation.
IMPORTANT! To ensure a successful installation, install the bath on a level oor.
Follow all state and local plumbing, building, and electrical codes.
Unpack and inspect the product for damage. Return the product to the carton until installation.
Read these instructions and determine the locations for all required components before beginning installation.
This bath is designed for drop-in, alcove, under-mount, or island installation.
Determine the location of the control amplier if it will be installed remotely. The control amplier includes a power
supply with a 36" (914 mm) cord and a 25' (7.6 m) cable.
A qualied electrician should install a 120 V, 15 A GFCI or RCD electrical outlet within the stud framing, and within 24"
(610 mm) of the control amplier. The user interface, transducers, and (if equipped) chromatherapy are powered through
connections with the control amplier.
Use conduit to route electrical power wires from the circuit breaker.
This bath will not easily t through doorways. Carefully plan how to move the bath into the installation area.
Install the bath to an adequately supported, level nished oor.
Provide properly dimensioned framing.
The bath basin requires no additional support when the suboor is level and square with the stud framing.
Plan for adequate mounting and connection space for the faucet.
This bath conforms to CSA B45.5/IAPMO Z124.
The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Kohler Co. is under license. Other trademarks and trade names are those of their respective owners.
Kohler Co. 3 1297608-2-E
Components
Control AmplifierTransducers
Chromatherapy
Lights
(If Equipped)
Chromatherapy
Control
(If Equipped)
AC Power
User Interface
Control
Amplifier
Power
Supply
Auxiliary Device
Vibracoustic and Chromatherapy (if equipped)
1297608-2-E4 Kohler Co.
Installation Sequence
24" (610 mm)
User Interface 6" (152 mm) Max
Control Amplifier
Access Panel
Transducer Wires
Chromatherapy Cable (If Equipped)
10" (254 mm)
User Interface
Cable
Power Supply
Control Amplifier Cable
IMPORTANT! Several included bath components will be powered by the control amplier with 25' (7.6 m) cables. Plan
the location of the control amplier so the cables will reach without being under tension.
For best results, follow the installation sequence below. Detailed instructions are found on the following pages of this
guide.
The illustration above shows a typical installation with the preferred user interface and control amplier locations.
Depending upon your bath, the installation will be similar.
Recommended Installation Sequence
Determine the locations for the bath components. Refer to the illustration for preferred locations.
Determine the location for the access panel required for servicing the control amplier.
NOTICE: Use wood studs to construct the bath frame. Metal framing may adversely aect vibracoustic quality.
Construct the framing for your bath.
Install the rough deck material.
Route the plumbing supply and drain lines for the bath.
Install the bath and drain.
Route the transducer wires to the control amplier location.
Install an electrical outlet within 24" (610 mm) of the control amplier location.
If equipped with chromatherapy, route the chromatherapy cable from the bath to the control amplier location.
Route the user interface cable from the control amplier area to the user interface location.
Install the control amplier.
Connect the transducer, user interface, optional auxiliary device (if used), and chromatherapy cable (if equipped) to
the control amplier.
Kohler Co. 5 1297608-2-E
Finish the walls and deck, and install the required access panel for the control amplier.
Connect the user interface cable to the user interface, and install the user interface.
Plug the control amplier into the electrical outlet.
Test the functionality of all bath components. Refer to the “Homeowners Guide” for operation.
1297608-2-E6 Kohler Co.
1. Prepare the Site
Drain Cutout
1/16" (2 mm)
Min
Water-Resistant
Deck Material
NOTICE: Measure your product for site preparation. Note the model number on the back of the bath, then visit the
product page at kohler.com for more information.
Flooring
Provide adequate support for the bath. Install additional support as needed.
Verify that the suboor is level. Adjust for level as needed.
Framing
CAUTION: Risk of product damage. Do not support the bath by the rim. The bath must be supported by the feet
or base. Plan to shim under the bath as needed when leveling the bath.
IMPORTANT! Several included bath components will be powered by the control amplier with 25' (7.6 m) cables. Plan
the location of the control amplier so the cables will reach without being under tension.
NOTICE: Use wood studs to construct the bath frame. Metal framing may adversely aect vibracoustic quality.
NOTICE: If installing the control amplier between studs, the stud spacing should be 16" (406 mm).
NOTE: The framing illustrated is less the nished wall and deck materials. Allow for the nished wall and deck material
thicknesses when constructing the framing.
Construct the framing, taking into account the thickness of the nished wall and deck materials.
For drop-in installations, provide a 1/16" (2 mm) to 1/8" (3 mm) gap between the framing and the underside of the
bath rim to ensure that the bath is not supported by the rim.
For under-mount installations, provide a 1/16" (2 mm) to 1/8" (3 mm) gap between the framing and the top surface of
the bath rim to ensure that the weight of the framing does not rest on the bath rim.
Construct stud framing or a pocket for the control amplier.
Provide a means to route the user interface cable through the wall to the control amplier.
Kohler Co. 7 1297608-2-E
Plumbing
NOTE: For through-the-oor drain installation, cut a drain hole in the oor to accommodate the drain connections.
Install the rough drain and water supply piping.
Cap the water supplies and check for leaks.
Install the drain to the bath following the drain manufacturer’s instructions. Do not connect the trapway at this time.
1297608-2-E8 Kohler Co.
2. Install the Bath
Mortar Cement Construction Adhesive
Apply construction
adhesive to the
support blocks.
Plastic Film
(Optional)
Mortar Cement
IMPORTANT! Fit maximum 1/8" (3 mm) thick spacers under the bath rim to ensure that the rim does not contact the
deck.
Verify that the suboor is level before proceeding. Use shims as needed.
Install the bath using one of the following two methods.
Kohler Co. 9 1297608-2-E
If desired, lay a plastic lm on wood suboors to prevent water absorption.
Spread a 1" (25 mm) to 2" (51 mm) layer of cement or mortar on the suboor.
With help, lift the bath into position. Use caution to avoid damaging components mounted to the bath.
Fit maximum 1/8" (3 mm) thick spacers under the bath rim.
Verify that the bath is level. Reposition or shim as needed.
Place a clean drop cloth in the bath basin to protect the surface.
Apply weight to the bath basin until the mortar sets.
Construction Adhesive Method
Apply a generous amount of construction adhesive to the boom of the support blocks or molded supports.
With help, lift the bath into position. Use caution to avoid damaging components mounted to the bath.
Fit maximum 1/8" (3 mm) thick spacers under the bath rim.
Verify that the bath is level and resting on all supports. Reposition or shim as needed.
Place a clean drop cloth in the bath basin to protect the surface.
Apply weight to the bath basin until the adhesive sets.
Cement or Mortar Bed Method
NOTICE: Do not use gypsum cement or drywall compound, as these materials will not provide a durable bond.
3. Install the Plumbing
CAUTION: Risk of property damage. Leaky drain connections will damage property. Make sure that a watertight
seal exists on all drain connections.
Make the nal drain connections.
Install the faucet valving following the manufacturer’s instructions. Do not install the faucet trim at this time.
Open the hot and cold water supplies.
Check all connections for leaks.
Fill the bath to the overow and check the drain connections for leaks.
1297608-2-E10 Kohler Co.
Inhaltsverzeichnis
Sprachen:
Andere Kohler Badewanne Handbücher
Kohler
Kohler K-11344 Montageanleitung
Kohler
Kohler K-856-CT Kurzanleitung
Kohler
Kohler K-1112P-GLA Kurzanleitung
Kohler
Kohler K-1377 Kurzanleitung
Kohler
Kohler K-1124 Bedienungsanleitung
Kohler
Kohler EVOK 22160A-0 Bedienungsanleitung
Kohler
Kohler K-1969-G Kurzanleitung
Kohler
Kohler Ceric K-8335-0 Bedienungsanleitung
Kohler
Kohler K-1131-CE Kurzanleitung
Kohler
Kohler K-941 Montageanleitung
Kohler
Kohler K-1145 Montageanleitung
Kohler
Kohler K-98155X Montageanleitung
Kohler
Kohler K-856-M Montageanleitung
Kohler
Kohler K-1189 Bedienungsanleitung
Kohler
Kohler Underscore K-1167-RH2-33 Montageanleitung
Kohler
Kohler K-1913 Montageanleitung
Kohler
Kohler Archer K-1125-RA Kurzanleitung
Kohler
Kohler K-870 Montageanleitung
Kohler
Kohler K-1257 Kurzanleitung
Kohler
Kohler K-856-CT Montageanleitung
Beliebte Badewanne Handbücher anderer Marken
Woodbridge
Woodbridge BJ500 Montageanleitung
Whirlpool
Whirlpool Ariel ARL-702 Bedienungsanleitung
TEIKO
TEIKO EXCELLENT DUO Bedienungsanleitung
American Standard
American Standard Colony 5-1/2' x 32" Bedienungsanleitung
American Standard
American Standard 3052OD.X0X Kurzanleitung
agape
agape MARSIGLIA AVAS1075 Bedienungsanleitung
