Kohler K-1913 Bedienungsanleitung

Installation Guide

Rising Wall Bath

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de Mcorresponden a México

(Ej. K-12345M)

Français, page ″Français-1″

Español, página ″Español-1″

K-1913

1128532-2-G

Important Information

WARNING: Risk of injury or property damage. Please read all instructions thoroughly before

beginning installation, including the following requirements.

WARNING: When using electrical products, basic precautions should always be followed,

including the following:

DANGER: Risk of electric shock. Connect only to circuits protected by a Ground-Fault

Circuit-Interrupter (GFCI) or Residual Current Device (RCD).

WARNING: Unauthorized modiﬁcation may cause unsafe operation and poor performance of

the product. Do not relocate the components, or make other modiﬁcations to the system other than

those speciﬁed in this document, as this could adversely affect the performance and safe operation.

Kohler Co. shall not be liable under its warranty or otherwise for personal injury or damage caused

by any such unauthorized modiﬁcation.

Building materials and wiring should be routed away from heat-producing components.

Install to permit access for servicing.

Grounding is required. The unit should be installed by a qualiﬁed service representative, and grounded.

WARNING: Risk of electric shock. A licensed electrician should make all electrical connections.

1128532-2-G 2 Kohler Co.

Important Information (cont.)

WARNING: Risk of electric shock. Disconnect power before servicing.

NOTICE: Follow all local plumbing and electrical codes.

Table of Contents

Important Information .............................................................. 2

Tools and Materials ............................................................... 3

Before You Begin ................................................................. 4

Parts Identiﬁcation ................................................................ 5

Construct the Framing ............................................................. 6

Conﬁrm the Correct Cutout .......................................................... 8

Install the Drain Lines and Rough Plumbing ............................................. 9

Remove the Shipping Brackets ...................................................... 11

Remove the Door ................................................................ 12

Remove the Pulley Assemblies and Mounting Brackets .................................... 14

Remove the Receptor Tray ......................................................... 16

Disconnect the Components ........................................................ 17

Position the Bath ................................................................ 18

Level and Secure the Bath ......................................................... 20

Attach the Water Supply to the Accumulator ............................................ 21

Install the Receptor Tray, and Connect the Drains ........................................ 22

Install the Mounting Brackets and Pulley Assemblies ...................................... 24

Install the Door ................................................................. 26

Attach the Counterweights ......................................................... 27

Connect the Components .......................................................... 29

Adjust the Bath Door ............................................................. 30

Seal/Drain System Electrical Connections .............................................. 32

Heated Surface Electrical Connections (if equipped) ...................................... 34

Conﬁrm Heated Surface Operation (if equipped) ......................................... 35

Install the Trim Caps and Access Panel ............................................... 36

Install the Finished Wall ........................................................... 38

Troubleshooting ................................................................. 38

Tools and Materials

Hex Wrenches

Removable

Bolt Adhesive 7/16", 9/16" and 7/8"

Open-end wrenches

• Crowbar or small

pry bar

• Metal Shims

• Masking Tape

• Pencil

• Drop cloth or

protective material

• Standard wood working tools

and materials

Plus:

Silicone

Sealant

Kohler Co. 3 1128532-2-G

Before You Begin

NOTICE: Risk of personal injury. Handle the bath and frame carefully. Some edges may be sharp or

rough.

NOTICE: Risk of product damage. Handle the bath and frame carefully. The bath will break or

malfunction if handled carelessly.

NOTICE: Risk of product damage. Do not support the weight of the bath by the perimeter of the rim. To

avoid damage to the product, support the bath by its base or feet.

NOTICE: Risk of product damage and personal injury. Due to the weight and installation difficulty of

the product, Kohler Co. recommends that two people perform this installation. There are several

installation sequences that are very difficult if performed alone.

IMPORTANT! Use care when removing screws. All screws will be reused unless otherwise indicated. Do

not strip the heads.

IMPORTANT! Do not cut or remove any cable ties unless instructed. They are used to hold critical parts

in place, and are designed to stay in place throughout the installation.

IMPORTANT! If the installation site is in an area where frequent or prolonged power outages occur,

Kohler Co. recommends that a minimum 350 VA Uninterruptible Power Supply (UPS) be installed as a

backup power source to the bath controller. The UPS will ensure that door functionality is not

compromised in the event of a power outage.

Follow all local plumbing and electrical codes.

Depending on the installation, it may be necessary to disassemble parts of the bath to pass

through all doorways, hallways, and stairways between the staging area and the bathroom. There

will be several points in this installation where the installer will be asked if further disassembly

is required. All adjustments have been made at the factory. Installation time is less for jobs

requiring little or no disassembly.

IMPORTANT! Save all hardware. If disassembly is required, save and organize all hardware. Hardware

will be reused unless otherwise speciﬁed.

There are supplemental installation instructions located on the back of the access panel.

This bath requires three drains with separate P-traps. Allow for three drains connecting at the

stack in your installation.

The installation instructions outline the only parts that need to be removed or disassembled during

the installation process. Although many parts may appear to be removable, do not disassemble

anything unless instructed.

Unpack the bath in an open area.

Inspect the unit for damage and make sure parts such as counterweights, access panel, and trim

caps are accounted for. The unit shown in this manual has a left-hand drain and may appear

different than the unit you have purchased.

1128532-2-G 4 Kohler Co.

Parts Identiﬁcation

Fill Spout/Accumulator

Trim Cap

Wall (RH)

Trim Cap

Wall (LH)

Roller Assembly (RH)

Pulley (LH)

Assembly

(includes limit

switch and

bumper)

Bumper

Mounting

Bracket

Access Panel

Support

Frame

Pulley Assembly (RH)

(includes limit switch and bumper)

Mounting Bracket

Power Connection for Door

(always opposite footwell drain side)

Receptor Tray

Bath

(Left Hand Drain shown)

Counterweight

Roller

Assembly

(LH)

Primary Footwell

Bath Drain

Second (Sidewall)

Drain Opening

Grab Bar

Controller

(Power Supply)

Door Assembly

(includes electronics

and brush seal)

Trim Cap Cover (LH)

Guide Tool

Trim Cap

Cover (RH)

Receptor Tray

Drain

Drain Valve for

Secondary Drain

Accumulator

Counterweight Guide

Product ID Label

Kohler Co. 5 1128532-2-G

1. Construct the Framing

All Installations

NOTICE: Measure your product for site preparation. Note the model number located on the blower

motor, then visit the product page at www.kohler.com for more information.

NOTICE: Adequate ﬂoor support must be provided.

NOTICE: Do not support the weight of the bath by the perimeter of the rim. To avoid damage to the

product, support the bath by its base or feet.

IMPORTANT! This product requires three 1-1/2″diameter drain outlets, three P-traps, and three separate

lines to the stack. In an ideal conﬁguration, none of the drains should be combined, as performance may

suffer and the potential for backﬂow will increase. If required, the two bathing vessel drains (#1 and #2 in

diagram) may be combined downstream from the P-traps into a single 3″diameter drain line.

IMPORTANT! The drain for the receptor tray (#3) requires a dedicated P-trap and stack connection.

Follow all local plumbing and electrical codes.

Leave the stud pocket open and do not install the ﬁnished wall until after the bath has been

installed. This installation is best done with access from the backside of the studs, particularly from

each side.

NOTICE: Follow all local plumbing and electrical codes.

If the installation site is in an area where frequent or prolonged power outages occur, Kohler Co.

recommends that a minimum 350 VA Uninteruptable Power Source (UPS) be installed as a backup

power source for the bath controller. This will ensure the door will open in the event of a power

outage.

Construct 2x4 or 2x6 stud

framing according to

the roughing-in information.

Position the rough plumbing.

Verify that the subfloor offers adequate support, and is flat and level.

Drain Access

Plumbing configuration

may vary.

To Accumulator

To Handshower

Hot

Cold

Floor Plan for Left-Hand Drain Model

16"

(406 mm)

10" (254 mm)

24-1/2"

(622 mm)

3-1/2"

(89 mm)

(LH) Drain

Cutout

7-3/4" (197 mm)

3-7/8"

(98 mm)

10" (254 mm)

Drain Cutout

Three Drain Cutouts (required)

Drain

Cutout

5-1/2" (140 mm)

30" (762 mm)

33-1/4"

(845 mm)

Front Edge of

Receptor Tray

GFCI Protected Outlet

(Opposite Side of

Accumulator Supply)

(RH) Drain Cutout

9-3/4"

(248 mm)

3-7/8" (98 mm

1128532-2-G 6 Kohler Co.

Construct the Framing (cont.)

Install a 120 V, 15 A, 60 Hz electrical outlet protected by a GFCI or RCD. The outlet must be located

on the side of the bath opposite the footwell drain outlet, within 24″(610 mm) of the controller).

Units with the heated surface feature will require a second electrical outlet within 24″(610 mm) of

the heated surface controller.

NOTE: Drain #1 is the sidewall drain/valve outlet. Drain #2 is the overﬂow and footwell drain outlet.

Drain #3 is the receptor tray drain outlet.

NOTE: Three drains are required for this product. Drains #1 and #2 require a 10″(254 mm) x 10″(254

mm) cutout.

NOTE: Drain #3, the receptor tray drain, requires a 10″(254 mm) x 10″(254 mm) cutout if access from

below is available. If above-the ﬂoor access is required to make the connections, a 10″(254 mm) x 16″(406

mm) cutout is required to allow access. The 10″(254 mm) wide cutout is critical to prevent subﬂoor

contact with the drain area of the receptor tray. If the subﬂoor and drain come into contact, enlarge the

cutout as needed or raise the bath using the adjustable feet. The receptor tray must be level and the drain

must rest comfortably through the subﬂoor.

Make sure the ﬂooring offers adequate support for the bath, and verify that the subﬂoor is ﬂat and

level.

The bath should be installed in an alcove installation. Construct a 2x4 or 2x6 frame.

Position the plumbing. Cap the supplies, and check for leaks.

Provide adequate ventilation and at least 15 cubic feet (.4 cubic meters) of open air space for cooling

the motor and supplying sufficient air to the blower. Do not install the blower motor closer than 1″

(25 mm) to the wall or other objects.

IMPORTANT! Use the chart below as a general guideline. Every installation varies. Hallways, corners,

stairways and other obstacles should be taken into account when determining how much disassembly is

required. Avoid unnecessary disassembly when possible.

Door Opening Recommended Installation Action

Larger than 33″(838 mm) No disassembly is required. Skip sections 4

through 8.

31″(787 mm) to 33″(838 mm) Remove the door from the bath and the

receptor from the support frame.

30″(762 mm) to 31″(787 mm) Full disassembly is likely. Follow all steps in

this manual.

Less than 30″(762 mm) The door open needs to be enlarged to a

minimum of 31″(762 mm).

Kohler Co. 7 1128532-2-G

2. Conﬁrm the Correct Cutout

All Installations

NOTE: Drain #3, the receptor tray drain, requires a 10″(254 mm) x 10″(254 mm) cutout if access from

below is available. If above-the ﬂoor access is required to make the connections, a 10″(254 mm) x 16″(406

mm) cutout is required to allow access. The 10″(254 mm) wide cutout is critical to prevent subﬂoor

contact with the drain area of the receptor tray. If the subﬂoor and drain come into contact, enlarge the

cutout as needed or raise the bath using the adjustable feet. The receptor tray must be level and the drain

must rest comfortably through the subﬂoor.

Measure the cutout to conﬁrm it is a minimum of 10″(254 mm) wide and 16″(406 mm) long.

Study the illustrations at the right. When the cutout is the correct size, the drain outlet on the

receptor tray and the surrounding material will not come in contact with the subﬂoor. The drain

outlet will protrude into the cutout when installed.

If the cutout is too small, the receptor tray will be too high. The counterweights will strike the

receptor tray when the door is raised and the door seals will not inﬂate.

16"

(406 mm)

10"

(254 mm)

Receptor Drain Cutout

Front Edge of

Receptor Tray

16" (406 mm)

10" (254 mm)

1/4" (6 mm)

Subfloor

1128532-2-G 8 Kohler Co.

3. Install the Drain Lines and Rough Plumbing

All Installations

Plumbing Access Considerations

Conﬁrm adequate mounting and connection space exists for the faucet speciﬁed for your

installation.

Conﬁrm adequate clearance for three P-traps.

If the unit is installed on a slab at a corner of the outside walls: Make connections to the

accessible end, or provide access to the plumbing connections if not able to do so through the front

access panel. Check the P-trap clearance for drains #1 and #2.

If the unit is installed on a slab back-to-back against the outside walls: Plan to provide adequate

access to the plumbing connections. Limited access is available through the access panel. Check the

P-trap clearance for drains #1 and #2.

When the unit is installed where the drain connections are accessible from below: Connections

can usually be made from underneath the unit.

Install the Rough Plumbing

IMPORTANT! This product requires three 1-1/2″diameter drain outlets, three P-traps, and three separate

lines to the stack. In an ideal conﬁguration, none of the drains should be combined, as performance may

suffer and the potential for backﬂow will increase. If desired, the two bathing vessel drains (#1 and #2)

may be combined downstream from the P-traps into a single 3″or larger drain line.

Install the plumbing lines following the valve and trim manufacturer’s instructions. Recommended

supply ﬁttings and locations are shown above.

Use 3/4″valves for optimal ﬁll time.

Flush out the drains.

Receptor Tray Drain

Mixing Valve

Transfer Valve

Accumulator

Handshower

Install the drain lines.

Slotted

Overflow Drain

Install water accumulator line.

Accumulator

Fitting (supplied)

(not supplied)

3/4" NPT

Recommended Plumbing Configuration for Left-Hand Models

46" (1168 mm) From Subfloor Recommended

Sidewall

Bath Drain 3

Kohler Co. 9 1128532-2-G

Install the Drain Lines and Rough Plumbing (cont.)

Install the receptor tray drain line and P-trap.

Install the sidewall drain line and P-trap.

Install the slotted overﬂow drain line and P-trap.

Install the water supply line which will connect to the accumulator. Do not connect at this time.

1128532-2-G 10 Kohler Co.

Andere Handbücher für K-1913

Inhaltsverzeichnis

Sprachen:

Andere Kohler Badewanne Handbücher

Kohler

Kohler K-1124 Bedienungsanleitung

Kohler

Kohler Archer K-1125-LA Kurzanleitung

Kohler

Kohler Underscore K-5718-XH2G Bedienungsanleitung

Kohler

Kohler K-856 Kurzanleitung

Kohler

Kohler K-1394 Series Kurzanleitung

Kohler

Kohler K-11344 Montageanleitung

Kohler

Kohler Underscore K-1822-G Bedienungsanleitung

Kohler

Kohler Stargaze K-24019-GHW Bedienungsanleitung

Kohler

Kohler 1835-GW-0 Montageanleitung

Kohler

Kohler K-1224P Kurzanleitung

Kohler

Kohler Sterling 7112 Series Montageanleitung

Kohler

Kohler K-1227 Montageanleitung

Kohler

Kohler K-1126 Kurzanleitung

Kohler

Kohler K-1245 Kurzanleitung

Kohler

Kohler K-1394 Series Bedienungsanleitung

Kohler

Kohler Underscore K-5714-XH2G Bedienungsanleitung

Kohler

Kohler Iron Works Tellieur K-727 Bedienungsanleitung

Kohler

Kohler EVOK K-18343T Bedienungsanleitung

Kohler

Kohler K-1449 Kurzanleitung

Kohler

Kohler Lakewood K-1649 Montageanleitung

Kohler

Kohler K-1209-HL Kurzanleitung

Kohler

Kohler Jacob Delafon E6D034-00 Bedienungsanleitung

Kohler

Kohler K-1126P Kurzanleitung

Kohler

Kohler Windward K-1115-LA Kurzanleitung

Beliebte Badewanne Handbücher anderer Marken

Agua

Agua BARTOLI-66 Bedienungsanleitung

PAA

PAA PRELUDE Bedienungsanleitung

BETTE

BETTE SILHOUETTE Bedienungsanleitung

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Bedienungsanleitung

Oliveri

Oliveri Naples Bedienungsanleitung

Lyons

Lyons Elite ETLxx663219 Series Bedienungsanleitung

Woodbridge

Woodbridge BJ500 Montageanleitung

Whirlpool

Whirlpool Ariel ARL-702 Bedienungsanleitung

TEIKO

TEIKO EXCELLENT DUO Bedienungsanleitung

American Standard

American Standard Colony 5-1/2' x 32" Bedienungsanleitung

American Standard

American Standard 3052OD.X0X Kurzanleitung

agape

agape MARSIGLIA AVAS1075 Bedienungsanleitung

Kallista

Kallista P50045-G5 Montageanleitung

Ariel

Ariel AM Series Bedienungsanleitung

Agua

Agua BAHLI-60 Bedienungsanleitung

DURAVIT

DURAVIT XViu 700443 Bedienungsanleitung

American Standard

American Standard Colony 2740 Series Bedienungsanleitung

Rapsel

Rapsel OFURO Handbuch