Kohler K-18647 Montageanleitung

Installation and Care Guide

In-Wall Tank and Carrier

Français, page “Français-1”

Español, página “Español-1”

K-18647

1247365-2-B

Tools and Materials

Before You Begin

IMPORTANT! 2x4 framing or larger is required for this installation.

IMPORTANT! In areas with freezing temperatures, install on an

interior wall. If installed on an exterior wall, provide adequate

insulation to prevent the possibility of freezing.

NOTE: If 2x6 framing is used, the drain outlet may be angled 45

degrees in either direction.

NOTE: This product is not intended to be used as a retroﬁt device

for 1.28 gpf (4.8 lpf) water closets.

Only bowl model K-76395 is compatible with this carrier.

During installation, make sure the inlet tube connections and

gaskets remain fully engaged to ensure a watertight seal.

Observe all local plumbing and building codes.

Qty: 8

3/8" x 2-1/2" (64 mm) Min

Lag Bolts with Washers

Plus:

• Conventional woodworking

tools and materials

• 3/8" x 2" (51 mm) Min

Concrete Expansion Bolts

(for concrete subflooring)

Optional:

• Assorted electrical tools

1247365-2-B 2 Kohler Co.

Roughing-In

23-1/4" (590 mm)

50-15/16"

(1294 mm)

1/2" NPT

3-3/16" (80 mm)

1-9/16" (40 mm)

Centerline

of Outlet

2x4 Studs

3-3/4"

(95 mm)

2x6 Studs

5-3/16"

(132 mm)

1-3/4 (44 mm)

1/4" (6 mm)

10-7/8" (276 mm)

15-1/4"

(387 mm)

Min

23"

(584 mm)

Max

28"

(711 mm)

Kohler Co. 3 1247365-2-B

1. Install the Framing

IMPORTANT! The waste outlet location is critical. Use the correct

dimension (shown above) from the front edge of the framing to the

center of the waste outlet for your installation.

NOTE: The waste outlet pipe may need to be relocated for this

installation.

NOTE: A PVC elbow is supplied with this product. A cast iron

elbow may be required by codes in some areas. The height of the

toilet drain pipe may need to be adjusted if the cast iron elbow is

used.

NOTE: Double studs must be used on either side of the stud

pocket.

Construct the stud pocket according to the dimensions shown.

2x4 Studs

or 2x6 Studs

23-1/4"

(591 mm)

PVC

Elbow

PVC Waste Outlet

1-3/4" (44 mm) [2x4 Studs]

3-1/4" (83 mm) [2x6 Studs]

Waste Outlet Cast Iron Outlet

2-7/8" (73 mm) [2x6 Studs]

1247365-2-B 4 Kohler Co.

Install the Framing (cont.)

Locate the center of the waste outlet from the front edge of the

framing to the dimension shown for your installation.

Waste Pipe Installation Options:

NOTE: These installation options are suggestions. Follow all

applicable codes in your area.

4″Diameter PVC

Install the supplied rubber, ribbed adapter onto carrier’s PVC

elbow and insert it into the 4″PVC waste outlet pipe.

The waste outlet pipe height must be sufficient to allow rubber

ribbed adapter to be fully inserted into waste outlet pipe.

NOTE: The 4″PVC waste outlet pipe is wider than the stud pocket

in a 2x4 installation requiring that the wall material be carved out

on both sides of the installation wall to ﬁt waste pipe.

3″Diameter PVC

Couple to carrier’s PVC elbow using ﬂexible coupler or a glued

PVC coupler.

NOTE: PVC or ﬂexible coupler may be wider than stud pocket in a

2x4 installation, requiring the wall material be carved out on both

sides of the installation wall to ﬁt coupler.

Cast Iron Waste Outlet

The cast iron outlet must be installed as required by local codes.

Use the KOHLER cast iron outlet speciﬁed on the speciﬁcation

sheet.

The recommended cast iron waste pipe will center 2-7/8″(73

mm) from the front of the frame.

NOTE: The cast iron waste pipe will not be centered inside 2x4

framing and will protrude beyond the back of the stud pocket. 2x6

framing or a chase behind 2x4 framing is required for cast iron

outlets.

Kohler Co. 5 1247365-2-B

2. Prepare the Carrier

Position the carrier face down on the ﬂoor.

Using a hex wrench, loosen the nuts securing the legs to the

carrier.

Raise the carrier 8″(203 mm) - 10″(254 mm) high to allow access

to the feet.

Tighten the nuts securing the legs to the carrier.

Mounting

Frame

PVC

Elbow

Front View

Drain

Clamp

1247365-2-B 6 Kohler Co.

3. Install the Drain Clamp

NOTE: If using 2x6 studs, install the drain mounting frame in the

back notches as shown.

Install the drain mounting frame into the front notches on the

bottom of the carrier.

Insert the PVC elbow into the mounting frame.

Secure the elbow in place with the drain clamp. Push the clamp

into the frame until it locks into place.

Back View

2x62x4

Kohler Co. 7 1247365-2-B

4. Adjust the Carrier Height

IMPORTANT! If the carrier is not correctly adjusted, the bowl rim

height may not be compliant with applicable codes.

NOTE: The minimum rim height is 15″(381 mm). The maximum

rim height is 23″(584 mm). The carrier can be adjusted up to 8″(203

mm), with 6″(152 mm) or less of adjustment sufficient in most

installations.

Move the carrier into place in the stud pocket.

Align the carrier ﬂush with the front edge of the studs. The front

of the carrier should be ﬂush with the front edge of the studs or

set back slightly for ﬁnished wall installation.

Check the front of the carrier for plumb.

Temporarily secure the carrier in place so it will not fall.

Install the threaded rods several turns into the carrier.

Make a mark on the carrier 2-5/8″(67 mm) above the top of the

threaded rod.

Measure from the ﬁnished ﬂoor to the mark (X) to determine the

rim height of the bowl.

Leg

Nut

Finished

Floor

Mark the carrier.

2-5/8"

(67 mm)

Threaded

Rods

1247365-2-B 8 Kohler Co.

Adjust the Carrier Height (cont.)

To adjust the carrier to the desired height, loosen the nuts

securing the legs to the carrier.

NOTE: As the carrier is lowered, make sure the elbow and gasket

(if present) align with the ﬂoor drain pipe.

Adjust the carrier until the desired height is reached. Securely

tighten the nuts using a wrench to secure the legs in place.

NOTE: If a cast iron elbow is required, make the connections

following all applicable codes.

Kohler Co. 9 1247365-2-B

5. Install the Carrier

IMPORTANT! It may be difficult to drill pilot holes for the feet lag

bolts if your carrier has been adjusted to a low height. If there is not

enough room to drill the pilot holes, mark their location and

temporarily remove the carrier to drill them.

Mark the hole locations for the eight lag bolts, one for each foot

and three on either side of the carrier.

Drill pilot holes (remove the carrier if needed) for the lag bolts.

NOTE: If the carrier is installed onto a concrete subﬂoor use

concrete expansion bolts (not supplied) when securing the feet of

the carrier.

Secure the carrier to the support studs using minimum 3/8’’ x

2-1/2’’ (64 mm) long lag bolts and washers (not supplied), one at

each location.

Lag Bolts

1247365-2-B 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-7776 Montageanleitung

Kohler

Kohler Carillon K-7806-95 Bedienungsanleitung

Kohler

Kohler K-10349 Montageanleitung

Kohler

Kohler K-4709 Bedienungsanleitung

Kohler

Kohler K-11550 Bedienungsanleitung

Kohler

Kohler K-485 Montageanleitung

Kohler

Kohler 10-Jet K-1000-H2 Montageanleitung

Kohler

Kohler K-7163 Montageanleitung

Kohler

Kohler JULY 16316M-4 Bedienungsanleitung

Kohler

Kohler K-15227 Series Montageanleitung

Kohler

Kohler MAXISPACE K-77217T Bedienungsanleitung

Kohler

Kohler 7098M Bedienungsanleitung

Kohler

Kohler Purist K-T14428 Bedienungsanleitung

Kohler

Kohler Fairfax K-12185 Montageanleitung

Kohler

Kohler Quiet-Close C3-455 Bedienungsanleitung

Kohler

Kohler K-8855 Bedienungsanleitung

Kohler

Kohler K-9132 Bedienungsanleitung

Kohler

Kohler Freshman K-4989 Bedienungsanleitung

Kohler

Kohler PURIST UPGRADE Bedienungsanleitung

Kohler

Kohler K-7179 Montageanleitung

Kohler

Kohler K-7127 Montageanleitung

Kohler

Kohler PURIST Series Bedienungsanleitung

Kohler

Kohler K-393 Bedienungsanleitung

Kohler

Kohler K-2369 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung