Kohler K-6284 Montageanleitung

Installation and Care Guide

In-Wall Tank and Carriage

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-6284

1142998-2-C

Tools and Materials

Before You Begin

IMPORTANT! 2x6 framing is required for this product. 2x4 framing

will not be deep enough to accommodate the carriage assembly.

IMPORTANT! In areas with freezing temperatures, install on an

interior wall. If installed on an exterior wall, provide adequate

insulation to prevent the possibility of freezing.

NOTE: This device is not intended to be used as a retroﬁt device

for 1.28 gpf (4.8 lpf) water closets.

NOTE: Performance may vary. This product was not tested with

toilets not listed as compatible.

Only bowl numbers K-6299 and K-6300 are compatible with the

carriage.

During installation, make sure the inlet tube connections and

gaskets remain fully engaged to ensure a watertight seal.

Carefully inspect the carriage and tank for damage.

Observe all local plumbing and building codes.

For Installations with a Bidet Seat

CAUTION: Risk of personal injury. If the optional electrical

outlet will be installed, it must be connected to a GFCI or

RCD protected circuit.

Assorted Drill Bits Silicone Plumbers

Grease 1/4" x 2" (51 mm)

Min Lag Bolts

2" Hole Bit

1/4 turn, 1/2" NPT

Supply Shut-off with 5/8"

or Shorter Handle

1/2"

Plus:

• Conventional

woodworking

tools and materials

• Cement board,

24" (610 mm) x

24" (610 mm) min

Optional:

• Assorted electrical

tools

5/8"

(16 mm)

1142998-2-C 2 Kohler Co.

Before You Begin (cont.)

If the optional electrical outlet will be installed, observe all local

electrical codes.

Kohler Co. 3 1142998-2-C

1. Install the Framing

IMPORTANT! This installation requires 2x6 studs. Note the

center-to-center stud dimension is not standard.

IMPORTANT! Note the 3-3/4″(95 mm) dimension from the front

edge of the framing to the center of the outlet pipe. This dimension

is critical for the installation.

NOTE: Refer to the speciﬁcation sheet for more details and

dimensions for roughing-in.

NOTE: The waste outlet pipe may need to be relocated for this

installation.

NOTE: A plastic elbow is supplied with this product. A cast iron

elbow may be required by codes in some areas. The height of the

toilet drain pipe may need to be adjusted if the cast iron elbow is

used.

Construct the stud pocket using lag bolts.

Install the stud pocket following the dimension shown.

19"

(483 mm)

19"

(483 mm)

Waste

Outlet

Pipe

3-3/4" (95 mm)

9-1/2" (483 mm)

2x6 Studs

19"

(483 mm)

3-3/4" (95 mm)

Ø 3-9/16"

(90 mm)

1142998-2-C 4 Kohler Co.

Install the Framing (cont.)

The center of the waste outlet should be 3-3/4″(95 mm) from the

front edge of the framing.

Kohler Co. 5 1142998-2-C

2. Prepare the Carriage

Raise the Carriage

NOTE: Raise the carriage for ease of installation. It will be lowered

again in a later step.

Position the carriage face down on the ﬂoor.

Loosen the nuts securing the legs to the carriage using the

supplied hex wrench.

Raise the carriage 8″(203 mm) - 10″(254 mm) high, enough to

allow room for a wrench and lag bolts over the feet.

Tighten the nuts securing the legs to the carriage.

Install the Electrical Box - Bidet Installations

NOTE: The electrical box is required when the K-4744 bidet seat

will be paired with the bowl. Skip this step for standard

installations.

Connect the electrical box to the carriage at the location shown.

Front View Back View

Electrical

Box

Hex

Wrench

Leg

Nut

Screws

1142998-2-C 6 Kohler Co.

3. Position the Elbow

Position the carriage upright in a secure position.

Gently turn the upper screw (labeled ″Open″) counterclockwise

while applying slight downward pressure on the support strap

until the strap comes free of the locking mechanism.

Move the end of the elbow into place from the front of the

carriage. Rotate the elbow downward as it moves through the

carriage.

With the ﬂared end of the waste pipe against the support strap,

insert the support strap upward into the locking mechanism as

far as possible.

Gently turn the lower locking screw (labeled ″Lock″) clockwise

until you hear a click to secure the waste pipe.

Unlock

Lock

Support Strap

Elbow

Kohler Co. 7 1142998-2-C

4. Install the Carriage

Move the carriage into place in the stud pocket.

Temporarily secure the carriage in place so it will not fall.

Align the carriage ﬂush with the front edge of the studs. The

front of the carriage should be ﬂush with the front edge of the

studs or set back slightly for ﬁnished wall installation.

Check the front of the carriage for plumb.

Mark the hole location for each foot.

Drill a pilot hole (remove the carriage if needed) to reduce the

risk of the lag bolt causing the stud to split or crack.

Secure the feet of the carriage to the studs using 2″(51 mm)

(minimum) lag bolts (not supplied).

Install the threaded rods several turns into the carriage.

Leg

Lag Bolt

Threaded

Rod

Front View

1142998-2-C 8 Kohler Co.

5. Adjust the Carriage Height

IMPORTANT! If the carriage is not correctly adjusted, the bowl rim

height may not be compliant with applicable codes. The ﬁnished

wall would need to be removed to make the correct adjustments if

the bowl height is not correct.

NOTE: For the K-6299 and K-6300 bowls, the minimum rim height

is 15-5/8″(391 mm) when the ﬁnished ﬂoor is even with the bottom

of the carriage legs. The maximum rim height is 26″(660 mm) when

the legs are fully raised. The carriage can be adjusted up to 12″(305

mm), with 6″(152 mm) or less of adjustment sufficient in most

installations.

Make a mark 2-5/8″(67 mm) above the top of the threaded rod.

Measure from the top of the ﬁnished ﬂoor to the mark (A) to

determine the rim height of the bowl.

Loosen the nuts securing the legs to the carriage.

As the carriage is lowered, make sure the elbow aligns with the

toilet drain pipe.

Nut

Leg

Front View

Finished

Floor

Mark the

carriage.

2-5/8"

(67 mm)

2-5/8"

(67 mm)

Kohler Co. 9 1142998-2-C

Adjust the Carriage Height (cont.)

If applicable, conﬁrm the gasket on the elbow stays correctly

positioned as it enters the toilet drain pipe.

Adjust the carriage until the desired height is reached. Securely

tighten the nuts using the provided hex wrench to secure the legs

in place.

If a cast iron elbow is required, make the connections following all

applicable codes.

1142998-2-C 10 Kohler Co.

Andere Handbücher für K-6284

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler K-6814 Montageanleitung

Kohler

Kohler K-7273-AF Montageanleitung

Kohler

Kohler BodySpa K-1030 Montageanleitung

Kohler

Kohler K-2096 Bedienungsanleitung

Kohler

Kohler 10742A-CP Bedienungsanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler K-682 Montageanleitung

Kohler

Kohler 1114111 Bedienungsanleitung

Kohler

Kohler K-14281 Bedienungsanleitung

Kohler

Kohler K-T16237 Bedienungsanleitung

Kohler

Kohler AIRFOIL 37273T Bedienungsanleitung

Kohler

Kohler K-1913 Montageanleitung

Kohler

Kohler K-2313 Bedienungsanleitung

Kohler

Kohler K-18355T Bedienungsanleitung

Kohler

Kohler Loure K-15285 Montageanleitung

Kohler

Kohler COMPONENTS K-EX27462T-NW-CP Bedienungsanleitung

Kohler

Kohler K-6130 Montageanleitung

Kohler

Kohler 76633T-B Bedienungsanleitung

Kohler

Kohler CARE K-22779T-1 Bedienungsanleitung

Kohler

Kohler K-9436 Bedienungsanleitung

Kohler

Kohler K-7127 Bedienungsanleitung

Kohler

Kohler K-7305 Betriebsanleitung

Kohler

Kohler K-11797T Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung