Kohler Kumin K-104K36-SANA-CP Bedienungsanleitung

Installation Guide

Centerset Bathroom Sink Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página“ Español-1”

1357694-2-A

Tools and Materials

Before You Begin

CAUTION: Risk of property damage. Do not use lithium

ion batteries with this product. Exposing lithium ion batteries

to water can result in a ﬁre.

Observe all local plumbing and building codes.

Shut off the water supply.

This faucet is for a single-hole bathroom sink.

For new installations, install the faucet and drain to the sink

before installing the sink.

The faucet shown in this guide may differ from your actual

product. The installation steps still apply.

In order for this faucet to function properly, install the faucet so

the sensor points directly toward the user.

1-1/4" to 1-1/2"

Hole Bit1/8"

Sealant TapePlumbers Putty

1357694-2-A 2 Kohler Co.

1. Faucet Installation

NOTE: Before drilling the mounting hole, use the following

dimensions for proper placement:

A 1-1/4″(32 mm) minimum to 1-1/2″(38 mm) maximum

diameter mounting hole is required.

A minimum distance of 1-3/4″(44 mm) is required between the

back of the spout and the wall to allow access to the screw.

A 1-1/8″(29 mm) maximum distance is required between the

sink bowl edge and the base of the spout.

Install the Faucet

Determine the mounting-hole location.

Drill a hole through the mounting surface according to the

surface manufacturer’s instructions.

Slide the O-ring over the ﬂexible hoses and stud, then seat the

O-ring into the groove on the underside of the spout.

Insert the spout with ﬂexible hoses and stud through the

mounting hole.

From under the sink, slide the rubber washer and bracket onto

the stud.

Thread the nut onto the stud and wrench-tighten to secure the

faucet to the mounting surface.

Flexible Hoses

Nut

Bracket

Stud

Rubber

Washer

O-Ring

Spout

Sensor

Kohler Co. 3 1357694-2-A

2. Install the Control Box

NOTE: Verify that the hose will reach the supply stop by attaching

the ﬂex hose to the control box inlet.

NOTE: Determine the proper mounting location according to the

Speciﬁcation Sheet.

Verify that the sensor cable is below the countertop.

Unthread the control box screws to remove the cover.

Drill pilot holes.

Use the standard wall anchors (provided) depending on your

wall material.

Attach the control box to the wall with the arrow pointing

upward. Secure with the two screws (provided).

Inlet

1357694-2-A 4 Kohler Co.

3. Connect the Control Box

IMPORTANT! The control box cover has slots for the spout wires

to ﬁt. Verify that the wires are not pinched when installing the

cover.

Connect the 3-pin sensor cable from the valve cover to the 3-pin

sensor cable from the spout (red, white, and green cables).

Connect the solenoid cable from the valve cover to the solenoid

cable from the valve box (red and green cables).

Connect the 2-pin sensor cable from the valve cover to the 2-pin

sensor cable from the spout (orange and black cables).

Loosely secure the cover to the control box for future access.

Valve

Box

Valve

Cover

Power

Cable

Solenoid

Cable

3-Pin

Sensor

Cable

Power

Cable

Solenoid

Cable

3-Pin

Sensor

Cable

2-Pin

Sensor

Cable

2-Pin

Sensor

Cable

Spout

Wires

Kohler Co. 5 1357694-2-A

4. Supply Connections

Inlet Connections

Connect the ﬂex hose from the control box to the supply stop.

Outlet Connections

Verify that the tube from the spout is the appropriate length to

reach the control box. Cut the tube if necessary. Remove any

burrs and sharp edges.

Insert the tube into the ﬁtting (control box outlet end) until the

tube stops.

Verify that the tube is secure.

Outlet Inlet

Flex Hose

Tube

From Spout

Supply

Stop

Flex Hose

1357694-2-A 6 Kohler Co.

5. Mixing Valve - If Included

If a mixing valve is included with your product, connect the

water outlet hose to the control box outlet.

Attach the supply hose to the control box inlet and outlet of

mixing valve.

Use a 3/8” compression connection (provided) to attach the cold

supply to the mixing valve cold inlet end (marked cold on the

adjustment plate).

Use a 3/8” compression connection (provided) to attach the hot

supply to the mixing valve hot inlet end (marked hot on the

adjustment plate).

Loosen the lock screw and adjust the temperature by rotating the

adjustment plate.

Retighten the lock screw.

Outlet

Hot Cold

Adjustment plate to

set water temperature.

Lock Screw

Kohler Co. 7 1357694-2-A

6. Install DC Power Unit

IMPORTANT! Verify that you are following the correct power

system installation based on your model number. For a hybrid

power unit installation, refer to ″Install Hybrid Power Unit″.

Unthread the control box screws to remove the control box cover.

Unthread the battery box screws to remove the battery box cover.

NOTE: Do not mix used and new batteries.

Insert 4 AA batteries (provided). Reinstall the battery box cover

and secure with the screws.

Connect the power cords.

Place the battery box into the empty space within the control box.

Secure the control box cover to the control box.

IMPORTANT! The area in front of the sensor must be free of

objects during the 2 minute learning cycle or the faucet may not

function properly.

Allow 2 minutes for the sensor to cycle through the automatic

sensing distance.

Battery

Box

Power Cord

1357694-2-A 8 Kohler Co.

7. Install Hybrid Power Unit

IMPORTANT! Verify that you are following the correct power

system installation based on your model number. For a DC power

unit installation, refer to ″Install DC Power Unit.″

Unthread the control box screws to remove the control box cover.

Connect the power cords.

Place the hybrid battery into the empty space within the control

box.

Secure the control box cover to the control box.

IMPORTANT! The area in front of the sensor must be free of

objects during the 2 minute learning cycle or the faucet may not

function properly.

Allow 2 minutes for the sensor to cycle through the automatic

sensing distance.

Hybrid Battery

Power Cord

Kohler Co. 9 1357694-2-A

8. Drain Installation

Disassemble the drain.

Apply plumbers putty to the underside of the ﬂange and attach.

Apply thread sealant tape to the drain pipe threads. Tighten the

nut.

Connect the trapway. Wipe away excess plumbers putty.

Stainless

(Non-Staining)

Plumbers Putty

1357694-2-A 10 Kohler Co.

Andere Handbücher für Kumin K-104K36-SANA-CP

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler BOTTICELLI 2393-WH Bedienungsanleitung

Kohler

Kohler K-702200 Montageanleitung

Kohler

Kohler 1202901-5-B Montageanleitung

Kohler

Kohler K-7116 Montageanleitung

Kohler

Kohler Mira Sport J03A Bedienungsanleitung

Kohler

Kohler EOLIA 8623T-B Bedienungsanleitung

Kohler

Kohler K-4991X Montageanleitung

Kohler

Kohler K-10280 Bedienungsanleitung

Kohler

Kohler K-7344 Montageanleitung

Kohler

Kohler REVE K-9273X Montageanleitung

Kohler

Kohler Clearflo K-7147 Montageanleitung

Kohler

Kohler K-3323X Montageanleitung

Kohler

Kohler BodySpa K-1030 Bedienungsanleitung

Kohler

Kohler 72704-4 Bedienungsanleitung

Kohler

Kohler Wave 7788T-4 Bedienungsanleitung

Kohler

Kohler Symbol K-T18485 Bedienungsanleitung

Kohler

Kohler K-6945 Bedienungsanleitung

Kohler

Kohler K-T9540 Montageanleitung

Kohler

Kohler K-7779 Montageanleitung

Kohler

Kohler K-7653 Montageanleitung

Kohler

Kohler Stance 14787A Bedienungsanleitung

Kohler

Kohler K-29221T Series Bedienungsanleitung

Kohler

Kohler K-97060-4-CP Bedienungsanleitung

Kohler

Kohler K-368 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung