Kohler K-4026-0 Bedienungsanleitung

Installation Guide

Toilet with Cleansing Seat

Français, page “Français-1”

Español, página “Español-1”

K-4026

1221754-2-F

Important Information

NOTE: This product is designed for installation with the electrical and water supplies located through the

wall.

Grounding Instructions

•This product should be grounded. In the event of an electrical short circuit, grounding reduces the

risk of electric shock by providing an escape wire for the electric current. This product is equipped

with a cord having a grounding wire with a grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded.

WARNING: Risk of electric shock. Improper use of the grounding plug can result in a risk of

electric shock.

•If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either

ﬂat blade terminal. The wire with insulation having an outer surface that is green with or without

yellow stripes is the grounding wire.

•Check with a qualiﬁed electrician or service personnel if the grounding instructions are not

completely understood, or if in doubt as to whether the product is properly grounded.

•This product is factory equipped with a speciﬁc electric cord and plug to permit connection to a

proper electric circuit. Make sure that the product is connected to an outlet having the same

conﬁguration as the plug. No adapter should be used with this product. Do not modify the plug

provided — if it will not ﬁt the outlet, have the proper outlet installed by a qualiﬁed electrician. If

the product must be reconnected for use on a different type of electric circuit, the connection should

be made by qualiﬁed service personnel.

Tools and Materials

Before You Begin

WARNING: Risk of electric shock. Disconnect the power before servicing.

WARNING: Risk of electrical shock. Connect only to a properly-grounded, grounding-type

receptacle which is protected by a Ground-Fault Circuit-Interrupter (GFCI) or Residual Current

Device (RCD). Do not remove the grounding pin or use a grounding adapter.

CAUTION: Risk of hazardous gases. If a new toilet is not installed immediately, temporarily place

a rag in the ﬂoor ﬂange opening.

IMPORTANT! The water supply input pipe must be a minimum of 1/2″copper pipe or 3/4″PEX tube to

provide the minimum water ﬂow for this product to operate properly.

Masking

Tape

Pencil or Felt

Tip Marker

Supply Stop 5/16" x 2-1/4"

T-Bolts Drill and 1/4" bitCaulk Gun Caulk

Rags

Silicone Grease

or Soap Socket Wrench

with 1/2" Deep Socket

Wax Seal

1221754-2-F2 Kohler Co.

Before You Begin (cont.)

NOTICE: The Canadian Electric Code requires receptacles installed in bathrooms to be located at least

39-3/8″(1000 mm) from a bath or shower if practical, but in no case less than 19-11/16″(500 mm). If the

installation is in Canada, install this unit in accordance with the Canadian Electrical Code, Part 1.

Observe all local plumbing and building codes.

Carefully inspect the new toilet for any damage.

There is a wiring schematic on the inside of the access cover.

Consult the Homeowners Guide for user directions.

Consult the Homeowners Guide for troubleshooting instructions.

Kohler Co. 3 1221754-2-F

1. Prepare the Site

WARNING: Risk of electrical shock. Connect only to a properly-grounded, grounding-type

receptacle which is protected by a Ground-Fault Circuit-Interrupter (GFCI) or Residual Current

Device (RCD). Do not remove the grounding pin or use a grounding adapter.

CAUTION: Risk of hazardous gases. If the new toilet is not installed immediately, temporarily

place a rag in the closet ﬂange.

NOTE: If the rough-in distance is less than 12″(305 mm) the seat may strike the wall when it is opened.

Conﬁrm the rough-in is 12″(305 mm) before installing the toilet.

Turn OFF the water supply.

Remove the old toilet.

Remove the wax residue from the ﬂange.

NOTE: T-bolts are not included. T-bolts should be 2-1/4″(57 mm) in length. Longer bolts will cause

difficulty in installation.

Install two 5/16″diameter x 2-1/4″long T-bolts into the ﬂoor ﬂange.

Mark the centerlines for the outlet on the ﬂoor.

Install the electrical supply at the location shown.

Install the water supply at the location shown.

(152 mm)

12"

(305 mm)

2-3/4" (70 mm)

Supply Stop

Floor Flange

T-Bolt

Scrape off the old

wax seal.

Centerline

1221754-2-F4 Kohler Co.

2. Install the Tank

CAUTION: Risk of property damage. Do not rock or lift the tank after placement. The seal created

by the wax ring may be broken, resulting in leaking.

Position the wax ring on the ﬂoor ﬂange.

Remove the tank from the vitreous toilet.

Align the tank over the ﬂoor ﬂange and T-bolts.

Lower the tank onto the ﬂoor ﬂange with the slots in the base of the tank aligned with the T-bolts.

Carefully align the tank on the centerline.

Press down evenly to set the wax ring.

Floor Flange

Tank

T-Bolts

Wax Ring

Kohler Co. 5 1221754-2-F

3. Secure the Tank

CAUTION: Risk of product damage. Do not overtighten the mounting nuts. Do not cut or shorten the

T-bolts.

Install a washer on each T-bolt.

Thread a nut onto each T-bolt.

Handtighten the nuts.

Wrench-tighten the nuts one quarter turn past hand-tight with a socket wrench.

Connect the water supply hose to the open port on the elbow.

Connect the water supply hose to the water supply stop.

Conﬁrm the cap on the elbow is tight.

Open the water supply stop.

T-Bolt

Washer

Nut

Base of

Tank Assembly

Connect to the

supply stop.

Flexible Hose

Capped

Port

Water Supply

Hose

1221754-2-F6 Kohler Co.

4. Check the Waterline

Valve

Adjustment

Waterline

Adjustment

Waterline

Flexible

Hose

Notch

Kohler Co. 7 1221754-2-F

CAUTION: Risk of property damage. Before use, close the valve using the adjustment screw to

avoid overﬂow.

NOTE: The waterline is marked inside the tank by a notch and a label.

Turn the valve adjustment screw counterclockwise to open the valve.

Allow the tank to ﬁll. Check the water level in the tank.

To adjust the water level, use a ﬂat-blade screwdriver to carefully turn the adjustment rod on the

inlet valve. Turning the rod counterclockwise will lower and clockwise will raise the water level.

If further adjustment is required, remove several inches of water from the tank and allow it to reﬁll.

Conﬁrm the water level is correct. Repeat until the correct water level is reached.

Turn the valve adjustment screw clockwise to close the valve.

Turn off the water supply.

5. Prepare the Tank

CAUTION: Risk of product damage. Conﬁrm the wires and water supply hose will not interfere with the

vitreous shell as it is lowered into place. The vitreous shell may cause damage to the wires or hose.

NOTE: It may be necessary to disconnect the water supply hose and tape it to the ﬂoor with the wires to

keep it clear of the vitreous while it is lowered into place.

Place the pump wiring harness, level switch wire, reﬁll tube, electrical plug, and wand wiring

harness on the ﬂoor at the location of the rear access opening and tape them on the centerline so

they will not interfere with the vitreous shell.

Clip the spray shield into place over the ﬁll valve.

Refill Tube

Tape

Level

Switch Wire

Electrical Plug

Pump Wiring

Harness

Wand Wiring

Harness

Spray Shield

Flexible

Hose

1221754-2-F8 Kohler Co.

6. Install the Vitreous Shell

WARNING: Risk of personal injury. The vitreous shell weighs 105 lbs (36 kg). Use proper lifting

technique when handling the vitreous shell. Lift and position the vitreous shell with a partner.

CAUTION: Risk of product damage. Do not set the shell down hard. Gently lift and move the shell if it

is not placed correctly. If handled carelessly, the shell may chip or break.

With assistance, carefully pick up the vitreous shell and slowly lower it over the tank.

Remove the cap from the capped elbow port.

Connect the cleansing hose to the elbow.

Make sure the trapway in the vitreous shell seats fully in the outlet gasket. If the vitreous shell does

not sit evenly on the ﬂoor, the trapway may not be properly seated.

Adjust the vitreous shell as needed until the trapway is properly seated.

Reconnect the water supply hose if it was disconnected.

Connect the Wires

Remove the tape from the ﬂoor wires and toilet.

Connect the level switch and reﬁll tube.

Connect the wand wiring harness and pump wiring harness.

Vitreous

Tank

Collar

Wand

Wiring Harness

Pump

Wiring Harness

Level Switch

Refill Tube

Kohler Co. 9 1221754-2-F

7. Install the Remote Control

Determine the desired location of the remote control docking station.

Position the docking station in the desired location and mark the location of the screw holes.

Remove the docking station.

Drill 1/4″holes at each of the screw locations.

Install anchors in each of the holes.

Remove the backing on the two-sided tape.

Attach the docking station to the wall using the two supplied screws.

Install the screw hole covers.

Install the batteries in the remote control (consult the Homeowners Guide for instructions if

needed).

Place the remote control on the docking station.

38" (965 mm) - 66" (1676 mm)

36"

(914 mm)

Docking Station

Remote Control

Screw

Double-Sided Tape

Anchor

Docking Station

Cover

1221754-2-F10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Toilette Handbücher

Kohler

Kohler ODEON K-8711T-2 Bedienungsanleitung

Kohler

Kohler K-23188X-C Montageanleitung

Kohler

Kohler PORTRAIT LITE K-4217 Bedienungsanleitung

Kohler

Kohler K-3900X Montageanleitung

Kohler

Kohler K-8688X Montageanleitung

Kohler

Kohler K-18751 Bedienungsanleitung

Kohler

Kohler K-45363R Montageanleitung

Kohler

Kohler OVE Series Bedienungsanleitung

Kohler

Kohler VEIL K-1666T-NS Bedienungsanleitung

Kohler

Kohler REVE K-24766T-S Bedienungsanleitung

Kohler

Kohler K-10349 Bedienungsanleitung

Kohler

Kohler VEIL K-1381T-S Bedienungsanleitung

Kohler

Kohler K-17757 Bedienungsanleitung

Kohler

Kohler K-4734-NY Montageanleitung

Kohler

Kohler K-3357 Montageanleitung

Kohler

Kohler K-11889 Montageanleitung

Kohler

Kohler REACH K-3983T-HC Bedienungsanleitung

Kohler

Kohler Persuade Circ K-3753 Benutzerhandbuch

Kohler

Kohler BRAZN 1PC K-EX22378T-NS Bedienungsanleitung

Kohler

Kohler Escale K-25090T-S Bedienungsanleitung

Kohler

Kohler K-17629MY Montageanleitung

Kohler

Kohler EIR Montageanleitung

Kohler

Kohler Heated French Curve K-4649 Montageanleitung

Kohler

Kohler STERLING 402024 Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung