Konica Minolta Bizhub 215 Bedienungsanleitung

E-1

INSTALLATION MANUAL

A3PE-9620-001BS0830301

I. Outline of installation procedures

When installing the machine and associated options as a system, follow the order shown on the upper.

Caution:

• For the detailed installation procedures for each option, follow the instructions given in the corresponding

installation manual and perform the procedures correctly. (Optional devices must be installed after com-

pleting the main body installation.)

• Once the Power Switch is turned ON, do not turn OFF it until the installation work has been completed.

• Lifting the machine in an awkward position or transporting it in a poorly balanced position could result in

personal injury. When transporting the machine, assign an adequate number of persons to the job and

ensure that each person can take a good position of not being excessively loaded.

<Machine mass> OC-512 and MB-505 included as standard: Approx. 29 kg (63-15/16 lb)

OC-512 or MB-505 included as standard: Approx. 27.5 kg (60-5/8 lb)

OC-512 and MB-505 not included as standard: Approx. 26 kg (57-5/16 lb)

*OC-512: Original Cover

MB-505: Multi Bypass Tray

Electronic system options

✱Electronic system options

Machine

MC-504*

*: Varies depending on each model/

applicable marketing area

DK-706* DK-707*PF-507 DK-708*

OC-512*DF-625

MB-505*

AD-509

IC-209 NC-504FK-510

MK-733

A3PEIXC001DA

Applied Machines: /

E-2

II. Installation space (unit: mm (inch))

bizhub 215 + DF-625 + PF-507 + DK-708

III. Pre-installation check items

1. Install the machine at a horizontal and stable

place.

2. Be sure to use a power source of the voltage and

frequency indicated in the product specifications.

Ensure that the current carrying capacity of the

power outlet is at least equal to the current listed

in the product specifications.

3. Power the machine directly from a dedicated

power outlet. (Do not use an extension cord.)

4. Do not plug or unplug the power cord with wet or

dirty hands, otherwise you may get an electric

shock.

5. Avoid a hot and humid environment, or a place

exposed to direct sunlight.

6. Avoid a dusty location, or a place near volatile

and flammable substances.

7. Avoid a poorly ventilated place.

IV. Accessory parts

* Varies depending on the applicable marketing

area

Note:

This manual provides the illustrations of the acces-

sory parts and machine that may be slightly differ-

ent in shape from yours. In that case, instead of

the illustrations, use the appearance of your

machine to follow the installation procedure. This

does not cause any significant change or problem

with the procedure.

A3PEIXC002DA

1109 (43-11/16)

570 (22-7/16) 429 (16-7/8)

1038 (40-7/8)

1388 (54-5/8)

358

(14-1/8)

No. Name Q’ty

1. Quick guide * 1

2. Installation manual (this manual) 1

3. User’s guide CD * 1

4. Developer 1

5. Power cord * 1

6. Power cord instruction * 1

7. CD-ROM * 1 set

8. Label (Legal restrictions on copying) * 1

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting the head in the plastic bag

involves danger of suffocation.

E-3

V. Unpacking the machine

1. Unpack the packaging box, and remove cushion-

ing materials and plastic bags from the box.

2. While keeping the machine level, take out the

machine from the box.

Caution:

• When transporting or moving the machine,

assign adequate number of persons.

• OC-512 and MB-505 included as standard:

Approx. 29 kg (63-15/16 lb)

• OC-512 or MB-505 included as standard:

Approx. 27.5 kg (60-5/8 lb)

• OC-512 and MB-505 not included as stan-

dard:

Approx. 26 kg (57-5/16 lb)

• Hold the machine by the locations (four places)

marked in the illustration and raise it while

keeping it in a horizontal position.

VI. Removing protective tape, packaging

materials and imaging unit

1. Remove protective tape and packaging materials.

A3PEIXC025DA

Mark

When OC-512 is included as standard

When MB-505 is included as standard

A3PEIXC006DA

A3PEIXC007DA

A3PEIXC008DA

A3PEIXC005DA

For the machine with fixed power cord

E-4

2. Remove the protective sheet from the operation

panel.

3. Open the right and front doors.

4. Remove the cover shown in the illustration and

unplug the connector. (One screw)

5. Unscrew the screws shown in the illustration to

remove the imaging unit. (Two screws)

Note:

• Do not touch or scratch the photoconductor.

• Cover the imaging unit, which has been

removed, with a protective cloth or similar

material.

6. Close the front door.

7. Remove the protective tape.

8. Push the ends of the transfer roller shaft in the

direction of the arrow to remove the fixing brack-

ets that fix the transfer roller.

9. Close the right door.

A3PEIXC009DA

A3PEIXC010DA

A0XXIXC012MA

A3PEIXC011DA

E-5

10. Slide out the drawer and remove the developer

and cushioning material.

11. Slide the drawer back in.

VII. Loading the developer

1. While pressing the connector tabs, push out the

connector from the imaging unit.

2. Unscrew the screws that secure the drum unit,

and then take out the drum unit by slightly open-

ing the lower part (the shadowed area) of the

drum unit. (Five screws)

Note:

• Do not open the lower part wide, otherwise the

charger may drop.

• Do not touch or scratch the photo conductor.

• Cover the drum unit, which has been removed,

with a protective cloth or similar material.

3. Remove the developing unit cover. (Three

screws)

A3PEIXC012DA

Developer

A0XXIXC040MA

Tab A0XXIXC013MA

Drum unit

Developing

unit

A0XXIXC014MA

E-6

4. Ready a packet of the developer and cut off one

corner of the aluminum packet with scissors.

5. While turning the gear in the direction of the

arrow, pour the developer evenly into the devel-

oper chamber.

Note:

• Turn the magnet roller in the direction of its nor-

mal rotation, and not the backward.

• Be sure not to let the developer get inside the

collar.

6. Reinstall the developing unit cover, ensuring that

its tabs are fitted properly into the slits. (Three

screws)

Note:

Do not tilt the developing unit or imaging unit after

the developer is poured.

7. Install the front of the drum unit first, and then the

rear part. Then, secure the screws. (Five screws)

Note:

• Do not open the lower part wide, otherwise the

charger may drop.

• Clean the screw groove before securing them.

• Do not touch or scratch the photo conductor.

8. Attach the imaging unit connector that is removed

in step 1.

9. Slide the imaging unit into the machine, and then

secure the screws. (Two screws)

Note:

• Make sure that the right door is open when slid-

ing the imaging unit into the machine.

• Align the shaft of the imaging unit with the guide

of the machine.

A0XXIXC015MA

Collar

A0XXIXC016MA

Temporarily tighten the screw first. A0XXIXC017MA

Temporarily tighten

the screw first.

Temporarily tighten

the screw first.

A0XXIXC019MA

E-7

10. Plug the connector, and then attach the cover.

(One screw)

11. Close the right and front doors.

VIII. Connecting the power cord

1. Connect the power cord.

Note:

This step may not be performed depending on the

applicable marketing area.

2. Plug the power cord into the power outlet.

IX. ATDC adjustment

Note:

Be sure to make this adjustment before setting the

toner bottle in the machine.

1. Turn on the power switch.

2. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

3. Press the [▲] or [▼] key to select “FUNCTION”

on the display.

4. Press the [OK] key.

5. Press the [▲] or [▼] key to select “TCR AUTO

ADJUST.”

6. Press the [OK] key to execute the ATDC adjust-

ment.

The following message appears in two minutes.

TCR AUTO ADJUST

TCR GAIN: ***

7. Turn off the power switch.

X. Installing the toner bottle

Note:

The toner bottle is not shipped with the machine.

Purchase one that is separately available.

1. Shake the toner bottle well about five times in the

vertical direction. Then, turn it over and repeat

the same procedure.

Note:

The toner can cake in the toner bottle. Be sure to

perform this procedure.

2. Open the front door.

3. Insert the toner bottle halfway with the tape side

up, and then slowly peel the tape off the bottle.

A3PEIXC014DA

A3PEIXC003DA

A0XXIXC018MA

Ta p e

E-8

4. Aligning the tip of the bottle tab with the

mark, insert the toner bottle all the way in.

5. Check that the toner bottle is all the way in, and

then turn the toner bottle in the direction of the

arrow to lock it.

6. Close the front door.

XI. Mounting the original cover

Mount the original cover.

Note:

This step may not be performed depending on

each model/applicable marketing area.

XII. Attaching the panel sheet

Attach the panel sheet to the operation panel.

Note:

• This step may not be performed depending on

the applicable marketing area.

• As the panel sheet is not supplied with the

machine, contact your operating company to

obtain the panel sheet when necessary.

XIII. Affixing the label (Legal restrictions

on copying)

Affix the label (Legal restrictions on copying) to the

position shown below.

Note:

This step may not be performed depending on the

applicable marketing area.

A0XXIXC050MA

A3PEIXC004DA

A3PEIXC013DA

A3PEIXC024DA

Andere Handbücher für bizhub 215

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Konica Minolta Multifunktionsdrucker Handbücher

Konica Minolta

Konica Minolta PagePro 1380 MF Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C652 Series Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 181 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 3602P Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 250 Bedienungsanleitung

Konica Minolta

Konica Minolta Drypro 832 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C650 Series Service-Handbuch

Konica Minolta

Konica Minolta accuriopress c6100 Originalbetriebsanleitung

Konica Minolta

Konica Minolta BIZHUB 162 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub c3110 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 350 Bedienungsanleitung

Konica Minolta

Konica Minolta Bizhub 4020 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB C351 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C754 Bedienungsanleitung

Konica Minolta

Konica Minolta Di470 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub PRO 950 Series Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 163 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 162 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 500 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C364e Leitfaden

Konica Minolta

Konica Minolta bizhub 423 Beilage

Konica Minolta

Konica Minolta bizhub 250 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 501 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 250 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung

Copystar

Copystar CS 4551ci Bedienungsanleitung

Konica Minolta bizhub 215 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken