Konica Minolta Bizhub C3850 Bedienungsanleitung

E-1

INSTALLATION MANUAL

A3GN-9581-00

Be sure to correctly follow the procedures in order as explained in this Installation Manual.

If you do not follow the procedure in order, the image trouble may occur.

I. Outline of installation procedures

When installing the machine and associated options as a system, follow the order shown on the upper.

Note:

• For the detailed installation procedures for each option, follow the instructions given in the corresponding

installation manual and perform the procedures correctly. (Optional devices must be installed after com-

pleting the main unit installation.)

• Once the Power Switch is turned ON, do not turn OFF it until the installation work has been completed.

Caution:

• Lifting the machine in an awkward position or transporting it in a poorly balanced position could result in

personal injury. When transporting the machine, assign an adequate number of persons to the job and

ensure that each person can take a good position of not being excessively loaded (mass: approx. 47.5 kg

(104-11/16 lb))

Machine

FS-P03

WT-P02

FK-512*

PF-P13 DK-P03*

AU-201

MK-738*

MK-P02

KP-101

*: Varies depending on the model and applicable marketing area.

Applied Machines: /

E-2

II. Installation space (unit: mm (inch))

bizhub C3850 + PF-P13 + DK-P03

III. Pre-installation check items

1. Select a level and stable place for installing the

machine.

2. Be sure to use a power source of the voltage and

frequency indicated in the product specifications.

Ensure that the current carrying capacity of the

power outlet is at least equal to the current listed

in the product specifications.

3. Power the machine directly from a dedicated

power outlet. (Do not use an extension cord.)

4. Do not plug or unplug the power cord with wet or

dirty hands, otherwise you may get an electric

shock.

5. Avoid a hot and humid environment, or a place

exposed to direct sunlight.

6. Avoid a dusty location, or a place near volatile

and flammable substances.

7. Avoid a poorly ventilated place.

IV. Notes on using touch panel

Be sure to instruct users on the following points.

• This machine uses a capacitive touch panel.

When you touch the touch panel, use your fin-

ger or the stylus pen for the capacitive touch

panel. If you touch the panel using your nail or

a pen tip instead of using your finger or the sty-

lus pen, the touch panel does not respond nor-

mally.

• Pressing the touch panel hard may cause dam-

age.

• Do not strongly press the panel or press it using

the sharp tip of mechanical pencils.

• The key is a finger tapping (quick light touch

using a finger) operation.

809 (31-7/8)

1453 (57-3/16)

555

(21-7/8)

254

(10)

1062 (41-13/16)

1014 (39-15/16)

884

(34-13/16)

(1-7/8)

335

(13-3/16)

385

(15-3/16)

733

(28-7/8)

E-3

V. Accessory parts

* Varies depending on each model and each mar-

keting area.

Note:

In case the FAX Kit is not included as the standard

equipment, keep the label (Super G3 label) at

hand. It is necessary for mounting the FAX Kit.

Note:

This manual provides the illustrations of the acces-

sory parts and machine that may be slightly differ-

ent in shape from yours. In that case, instead of

the illustrations, use the appearance of your

machine to follow the installation procedure. This

does not cause any significant change or problem

with the procedure.

VI. Unpacking the machine

1. Raise and remove the packing carton.

2. Remove the accessory parts and cushions on the

machine and open the plastic bag covering the

machine.

3. Assign two or more persons and put their hands

at the positions indicated in the illustration to

raise the machine from the box, and place the

machine on the horizontal and robust place.

No. Name Q’ty

1. Safety Information Guide 1

2. Quick start guide 1 set

3. Installation manual 1 set

4. User’s guide CD 1

5. CD-ROM 1 set

6. Paper size label 1 set

7. Label (Legal restrictions on copying) * 1

8. Label (Super G3 label) 1

9. Panel sheet 1

10. Power cord instruction * 1

11. Power cord 1

12. Modular cable * 1

13. Cord clamp * 1

14. Cover A

15. Cover B

16. Screw A 2

17. Screw B 2

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting the head in the plastic bag

involves danger of suffocation.

Be sure to hold the place specified in the

User’s Guide or other manuals to transfer

the machine.

Holding other places than the specified in

transferring the machine could cause per-

sonal injury due to the drop of the

machine or other reasons.

(Machine mass: approx. 47.5 kg (104-11/

16 lb))

E-4

VII. Removing protective tape, packing

and other shipping materials

1. Remove tapes for protective sheet and get rid of

the protective sheet.

2. Remove all protective tapes and protective mate-

rials used for fixing the machine housing.

3. Open the automatic document feeder (ADF) and

remove the protective tape and protective mate-

rial.

4. Slide the scanner lock lever to the unlock side

and close the ADF.

5. Open the front door.

6. Pull the fornt lever of a toner cartridge to the left.

E-5

7. Hold the handle of the toner cartridge, then pull it

out.

8. Hold the toner cartridge with both your hands,

then shake it several times.

9. Check that the color of the toner cartridge

matches that of the insertion slot in the main unit,

then push the toner cartridge to the back.

Note:

Make sure that the toner cartridge is pushed all the

way in.

10. For the other toner cartridges, perform the same

procedure as steps 6 to 9.

11. Remove protective tapes for the toner cartridges

of each color to remove protective films.

Never touch the electrical contacts of the

toner cartridge or the imaging unit, as an

electrostatic discharge may damage the

product.

Electrical contacts

E-6

12. Remove protective films for the imaging units of

each color.

13. Close the front door.

14. Open the right door.

15. Push up the two levers of the fusing unit cover.

16. Remove the protective materials from the fusing

section.

17. Push down the two levers of the fusing unit

cover in step 15.

18. Remove the protective materials from the trans-

fer roller unit.

19. Close the right door.

E-7

20. Slide out the tray 1 and remove the protective

materials from the inside of the tray.

Note:

Take care not to touch the surface of the paper

feed roller. If you touch it by mistake, wipe off any

dirt on the roller surface using dry cloth.

VIII. Loading the tray 1

1. If the paper lifting plate is raised, push it down by

hand to lock it.

2. Slide the paper length guide to the appropriate

paper size.

3. Set paper with the printing side upward and slide

the paper width guide to the paper size.

Note:

Make sure that the top level of the paper stack

does not exceed the ▼(MAX) paper level indica-

tor.

4. Slide the tray 1 back in.

IX. Mounting the accessory parts

1. Install the supplied cover A.

(Two supplied screws A)

2. Install the supplied cover B.

(Two supplied screws B)

E-8

X. Connecting the power cord

1. Remove the screw of the main unit shown in the

illustration.

Note:

Execute this step only if the cord clamp is supplied

with your machine.

2. Connect the plug of the power cord into the main

unit.

3. Secure the power cord using the supplied cord

clamp. (One screw removed in step 1)

Note:

This step may not be performed depending on the

applicable marketing area.

4. Plug the power cord into the power outlet.

XI. Connecting the network cable

Connect the main unit and networking equipment

(HUB) using the network cable.

Note:

The following shows the recommended network

cables that correspond to each communication

speed.

• 10BaseT/100BaseTX: Category 5

• 1000BaseT: Category 5E, Category 6

E-9

XII. Connecting the modular cable

Note:

This step may not be performed depending on the

applicable marketing area.

Connect the supplied modular cable to the LINE

port.

XIII. Initial Settings

1. Turn ON the Main Power Switch.

2. Follow the instruction on the screen to complete

the initial settings in order of Fax Target, Date

Setting, Time Setting, Time Zone and Language

Selection Display.

3. For products equipped with a fax as standard,

when the initial screen appears after the initial

settings are complete, perform the fax sending

and receiving tests between the machine and

either the store which offers the service or the

local retailer, to check that it can be operated nor-

mally.

XIV. Notes when performing dial transfer

Note:

Refer to this chapter only if your machine comes

with the FAX function as standard.

After setting the fax target, dialing operations may

be selected after the switchboard dial tone is

detected depending on the destination. In this case,

depending on the switchboard connected to the

machine and the type of dial tone received from the

switchboard, dialing operations may not be avail-

able. If that happens, you may be able to avoid the

problem with the following setting.

1. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

2. Touch “ .”

3. Touch “Fax Settings.”

4. Touch “Network.”

5. Touch “Dial Tone Detection.”

6. Touch “OFF.”

7. Touch “OK.”

8. Continue to touch “Close” until the initial screen

appears.

9. Turn OFF and ON the Main Power Switch.

Note:

When displayed the Service Mode screen, be sure

to turn off the main power after exiting the Service

Mode screen and wait for 10 seconds or more

before turning on.

E-10

XV. Affixing the labels

1. Affix the label (Legal restrictions on copying) to

the position shown below.

Note:

This step may not be performed depending on the

applicable marketing area.

2. Affix the label (Super G3 label) to the position

shown below.

Note:

Execute this step only if your machine comes with

the FAX function as standard.

3. Affix the paper size label to the tray 1 according

to the size of the paper used.

4. Affix the supplied panel sheet to the surface of

the operation panel.

Note:

• The panel sheet is affixed on customer request.

• The panel sheet must be kept by the customer.

Andere Handbücher für Bizhub C3850

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Konica Minolta Multifunktionsdrucker Handbücher

Konica Minolta

Konica Minolta bizhub 200 Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 2590 MF Bedienungsanleitung

Konica Minolta

Konica Minolta PagePro 1390 MF Kurzanleitung

Konica Minolta

Konica Minolta bizhub 750 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub36 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 215 Bedienungsanleitung

Konica Minolta

Konica Minolta 7013 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub c3110 Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 2480 MF Kurzanleitung

Konica Minolta

Konica Minolta PagePro 1390 MF Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C754 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 4690MF Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35P Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C550i Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB C10 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C554 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C451 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 1690MF Montageanleitung

Konica Minolta

Konica Minolta bizhub PRESS C1100 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 160 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C451 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 4690MF Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 215 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB PRO 1050 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung

Copystar

Copystar CS 4551ci Bedienungsanleitung