Kontron 104 Bedienungsanleitung

V PANEL

104 / 121 / 150 / 170 / 190

User manual

Rel. 08.2005 Ver.01

0-0096-3132

The German version of this manual is not available.

Die deutsche Version ist nicht verfügbar.

StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual

2© Copyright Kontron Embedded Computers GmbH

Kontron Embedded Computers GmbH

Werner-von-Siemens-Str. 1

93426 Roding

Phone: +49 9461 950 -0

Fax: +49 9461 950 -100

e-mail: [email protected]

Internet: http://www.kontron.com

Manual History

Date Version Changes

Aug.2005 01 First edition

StockCheck.com

http://www.kontron.com 3

Werner-von-Siemens Str.1

D - 93426 Roding

Tel: +49 9461 950 - 0

Fax: +49 9461 950 - 100

All rights are reserved

No part of this product, including the product and software may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any lan-

guage in any form by any means without the express written permission of

Kontron Embedded Computers GmbH (herinafter referred to as Kontron) ex-

cept documentation kept by the purchaser for backup purposes.

TRADEMARKS

All trademarks mentioned in this manual are registered properly of the respec-

tive owners.

CE-CONFORMITY

The following requirements, standards, specifications constitute part of the dec-

laration:

EN 55022 class A EN 55024 EN 60950

EN 61000-3-2 EN 61000-3-3 EN 61000-6-2

The validation of this declaration depends on the properly use of the product.

FCC Class A Radio Frequency

This equipment has been tested and found to comply with the limits for a Class

Adigital device, pursuant to 1/47 CFR Part 15.109 ClassAof FCC rules. Opera-

tion is subject to the following two conditions:

1. This device may not cause harmful interference and

2. This device must accept any interference received, including interference

that may cause undesired operation.

The limits of FCC Part15 classAare designed to provide reasonable protection

against harmful interference in residential installation. This equipment gener-

ates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interfer-

StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual

4© Copyright Kontron Embedded Computers GmbH

ence to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference

by more of one or more of the following measures:

1. Reorient or relocate the receiving antenna

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

4. Consult the dealer or an experienced radio/television technican for help.

Notice1: The changes or modifications not expressly approved by the party

responsible for compliance could void the user`s authority to operate the equip-

ment.

Notice2: Shielded interface cables, if any, must be used in order to comply with

emission limits.

CAUTION !

RISK OF EXPLOSION IF BATTERY IS REPLACED

BY AN INCORRECT TYPE

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

StockCheck.com

http://www.kontron.com 5

Werner-von-Siemens Str.1

D - 93426 Roding

Tel: +49 9461 950 - 0

Fax: +49 9461 950 - 100

Table of contents

Trademarks ................................................................................................3

CE-Conformity............................................................................................3

1. Introduction .................................................................................................6

2. Overview ....................................................................................................8

3. Hardware Installation...................................................................................9

3.1 Connect external devices ................................................................9

3.2 Connect internal devices ............................................................... 11

3.3 Internal Jumper setting ..................................................................12

3.4 LED Status indicators ....................................................................14

4 Software installation ..................................................................................15

4.1 Application software and operating system ...................................15

4.2 Hardware drivers ...........................................................................15

5. Technical Details .......................................................................................23

5.1 Mechanical ....................................................................................23

5.2 Electronical ...................................................................................23

5.3 Environment .................................................................................24

5.4 CE Directives and Standards........................................................24

5.5 Connector pinout ...........................................................................24

5.6 Options .........................................................................................31

5.7 Block diagram...............................................................................33

6. Maintenance ........................................................................................34

6.1 Customer service...........................................................................34

6.2 Cleaning ........................................................................................34

6.3 Return and repair..........................................................................34

6.4 Packaging......................................................................................35

7. Troubleshooting ...................................................................................36

7.1 FAQ ...............................................................................................36

8. Disposal...............................................................................................36

9. Appendix..............................................................................................36

StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual

6© Copyright Kontron Embedded Computers GmbH

1. INTRODUCTION

1.1. APPROPRIATE USE

The main purpose of the V Panel is the use and operation with 24VDC-power-

sources.

The surrounding area of the Panel are dry rooms.

The Panel is intended for industrial applications in machine and plant control

engineering.

The user is not entitled to change the system components or open the body

without consultation to Kontron.

1.2 ITEM CHECKLIST

Your Panel comes securely packaged in solid shipping carton(s). Upon receiv-

ing your Panel, open the carton(s) and remove the contents carefully.

The shipping carton should contain the following items:

- V Panel 10,4” 12,1” 15” 17” or 19”

- CPU Support CD (optional)

- 24V DC Power cord (optional)

- This user manual (optional)

- Software installation CD if implemented

Carefully inspect each component to ensure that nothing is missing and/or

damaged. If any of these items is missing or damaged, please contact Kontron

immediately. Preserve of of the packing material for future transportation.

1.3 IMPORTANT SAFETY INSTRUCTIONS

This section gives you detailed information about how to maintain a safe

environment while using the Panel. You can maintain its condition and perfor-

mance by following these guidelines. Please read it carefully to ensure maxi-

mum safety.

Be careful about the power supply input voltage. The Panel has specific

power requirements.

Please prevent the Panel from humidity.

Never pour any liquid on the Panel, this may cause fire or electrical shock.

Place the Panel on a reliable surface when installing.Adrop or fall may cause

damage.

StockCheck.com

http://www.kontron.com 7

Werner-von-Siemens Str.1

D - 93426 Roding

Tel: +49 9461 950 - 0

Fax: +49 9461 950 - 100

Do not leave the Panel in an unconditional environment. Storage temperature

above 70°C may damage the Panel.

The opening on the enclosure are for air convection, protect the Panel from

overheating. DO NOT COVER THE OPENINGS

If the Panel is not in use for a long time, disconnect it from mains to avoid

possible damage by transient overvoltage.

If you had to open the housing of the Panel in service cases, all single parts of

the plant must first be switched off, after which the Panel can be disconnected

fromtheplant. Secure eachpartagainstaccidentally switchedonduring service.

Following service activities on the Panel could cause failures.

• Metal objects such as screws or tools fall on or in the Panel

• Cables are removed or inserted during operation.

• Plug-in cards are removed or inserted during the Panel is

switched on.

All cautions and warnings on the Panel should be noted.

The system has to shut down and checked immediately by service staff, if one

of the following situation appears:

• The power cord or plug is damaged.

• Liquid has penetrated the Panel.

• The Panel is exposed to moisture.

• Obvious sign of breakage are visible.

• System did not work properly or you can not get it work

according to the application requirements.

StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual

8© Copyright Kontron Embedded Computers GmbH

2. OVERVIEW

The Kontron V Panel computer is a high performance system. The compact

designenablesan integrationevenunderthe condition ofvery restrictedspaces.

Our 100% industiy capable, scalable Panel meet the highest requirements

concerning shock, vibration and temperature resistance. The system also

provides a high resistance under tough EMC conditions.

Features:

- Display sizes 10,4“ 12,1“ 15” 17” and 19”

- Display type TFT active Matrix LCD with resistive touch.

- Color depth up to 32 bit

- Max. Resolution 1280x 1024

- Intel Pentium M Processor up to 1.1 Ghz

- Main memory up to 1024 MB on SDRAM

- Standard interfaces 3x USB, 2x PS/2, 1x LPT, 2x LAN, 4x RS232

- Input power of 24 VDC

- Installation of two PCI extension cards.

- Front side protection in IP65 (conform to EN 60529)

- Operating temperature up to 50°C

- Operating system Windows and Linux

- Dimension 10.4” 295mm x 348mm x 121mm

12.1” 327mm x 400mm x 121mm

15.0” 362mm x 452mm x 123mm

17.0” 390mm x 465mm x 130mm

19.0” 426mm x 516mm x 135mm

- All connectors build for industrial standards

- Shock and vibration tested

- Embedded architecture long-life electronic components

- Optional:Stainlesssteel front,front USB, PowerON switch,power LED

StockCheck.com

http://www.kontron.com 9

Werner-von-Siemens Str.1

D - 93426 Roding

Tel: +49 9461 950 - 0

Fax: +49 9461 950 - 100

3. HARDWARE INSTALLATION

Attention!

The weight of the Panel is about 7kg

Carry it on with both hands!

The Panel of this type is developed to work in a control cabinet. Thereby it must

be pointed that all the environmental conditions must be considered.

When installing the Panel take care that there is enough area for ventilations on

rear side. For details go to item housing dimensions.

If your Panel was delivered without software install a keyboard and mouse.

If operating system and software is installed, the touch is working and cali-

brated.

Look up for further settings e.g. BIOS on the ETX board manuals.

3.1 CONNECT EXTERNAL DEVICES

Toget detailedinformation about pinoutof eachconnector please lookto chapter

“technical details”.

COM 3

MOUSE

KEYBOARD

LAN 1

USB

LPT

COM 1 CRT COM 2 LAN 2

POWER

HDD

RESET POWER

POWER-ON

Fieldbus

Fig. 3-1

3.1.1 PS/2 Keyboard and Mouse

Use this connector to connect PS/2 mouse and keyboard.

3.1.2 LAN1 Port

Thisconnector provides a external interfaces10/100 BaseTon RJ45 to connect

your Panel to other devices in a network.

StockCheck.com

V Panel 104 / 121 / 150 / 170 / 190 User Manual

10 © Copyright Kontron Embedded Computers GmbH

3.1.3 USB port

This connector provides two external USB 2.0 interfaces

3.1.4 Parallel port LPT

Use this port to connect a printer or other parallel devices.

3.1.5 Serial Interface COM1, COM2, COM3

Three serial interfaces enables you to connect a external device with 9 pin

DSUB connector such as mouse or modem. COM2 is selectable as a input for

programming fielbuscontroller.

3.1.6 Fieldbus interface CAN / CANOpen / Profibus / DeviceNet

External connector of internal fieldbus controller. Interface to connect CAN,

CANOpen, Profibus/MPI or DeviceNet devices. All interfaces in master or

slave configuration available.

3.1.7 CRT Monitor

Connector and interface to VGA/CRT monitor .

3.1.8 Second LAN2 Port

This connector provides a second external interfaces 10/100/1000 BaseT on

RJ45 connector to your panel to other devices in a network.

3.1.9 Reset

Reset Switch reset the hole unit.

3.1.10 Main power IN

Use this connector to connect the power supply of 24VDC. Please note the

Power requirements (See chapter technical details).

3.1.11 Power ON button

Enables you to switch on and off the main system.

3.1.13 Front USB

Use this port behind a cover to connect USB devices direct on the panel front

StockCheck.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kontron Computerhardware Handbücher

Kontron

Kontron ETX -CN8 Bedienungsanleitung

Kontron

Kontron cPCI-DMXS64GX Produkthandbuch

Kontron

Kontron AT8901 Bedienungsanleitung

Kontron

Kontron SDML-WLU0 Series Bedienungsanleitung

Kontron

Kontron CP-ADAP-P47-PB (3U) Bedienungsanleitung

Kontron

Kontron KBox A-150-APL Bedienungsanleitung

Kontron

Kontron COM Express Extension Bedienungsanleitung

Kontron

Kontron AT8402 Bedienungsanleitung

Kontron

Kontron KISS Stor Slim Bedienungsanleitung

Kontron

Kontron KBox F-420-WLU Bedienungsanleitung

Kontron

Kontron COMe-mSP1 Bedienungsanleitung

Kontron

Kontron COMe-cBTi6R E3845 8GB/16S Bedienungsanleitung

Kontron

Kontron COMe-cDC2 Bedienungsanleitung

Kontron

Kontron CP6500-V Bedienungsanleitung

Kontron

Kontron cPCI-MXS64 Produkthandbuch

Kontron

Kontron PC/104-PCMCIA-1 Bedienungsanleitung

Kontron

Kontron nanoETXexpress-HMI Baseboard Bedienungsanleitung

Kontron

Kontron SMARC-sAMX6i Bedienungsanleitung

Kontron

Kontron MOPSlcdGX1 Bedienungsanleitung

Kontron

Kontron AT8060 Bedienungsanleitung

Kontron

Kontron MITX-CFL0 Series Bedienungsanleitung

Kontron

Kontron nanoETXexpress-SP Bedienungsanleitung

Kontron

Kontron ETX-CD Bedienungsanleitung

Kontron

Kontron nanoETXexpress-SP Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

Measurement Computing

Measurement Computing CIO-EXP-RTD16 Bedienungsanleitung

Matrox

Matrox DigiSuite DigiMix Installations- und Betriebsanleitung