Korenix JetI/O 6510 Bedienungsanleitung

Korenix JetI/O 6510

Industrial Intelligent Ethernet I/O Server

User Manual

Sept. 2009 (V1.5)

www.korenix.com

Korenix JetI/O 6510

Industrial Intelligent Ethernet I/O Server

User Manual

Reproduction in any form or by any means without permission is prohibited.

Index

INTRODUCTION .............................................................................................................. 1

1.1

VERVIEW OF

I/O

6500

ERIES

............................................................................. 1

1.2

ACKAGE

HECKLIST

.................................................................................................. 2

1.3

I/O

6510

NTRODUCTION

....................................................................................... 2

1.4

I/O

6510

RODUCT

PECIFICATION

....................................................................... 3

HARDWARE INSTALLATION.......................................................................................... 4

2.1

ARDWARE

NTRODUCTION

......................................................................................... 4

2.2

IRING

OWER

NPUT

................................................................................................ 5

2.3

IRING

I/O

ONNECTORS

........................................................................................... 6

2.4

I/O

6510

IRING

XAMPLE

................................................................................... 6

2.5

IRING

ARTH

ROUND

............................................................................................. 7

2.6

IRING

AST

THERNET

ORTS

.................................................................................. 7

2.7

-R

AIL

OUNTING

NSTALLATION

.............................................................................. 7

PREPARATION FOR MANAGEMENT ............................................................................ 9

3.1

NDERSTAND THE

THERNET

I/O

ERVER

RCHITECTURE

........................................... 9

3.2

REPARATION FOR

EMOTE

ANAGEMENT

.................................................................. 9

FEATURE CONFIGURATION.........................................................................................11

4.1

LOCK

I/O

ONFIGURATION

TILITY

...........................................................................11

4.2

LOCK

I/O

OPC

ERVER

TILITY

.............................................................................. 29

4.3

SNMP..................................................................................................................... 33

4.4

UI.................................................................................................................... 33

4.5

OW TO

PGRADE

IRMWARE

................................................................................... 33

4.6

ONFIGURATION

ACKUP

ESTORE

ESET

EFAULT

AND

EBOOT

........................... 35

MODBUS/TCP COMMAND SET.................................................................................... 38

5.1

NTRODUCTION OF

ODBUS

/TCP

ROTOCOL

............................................................ 38

5.2

I/O

6510

ODBUS

/TCP

DDRESS

APPING

........................................................ 39

APPENDIX...................................................................................................................... 88

6.1

SNMP

MIB.............................................................................................................. 88

6.2

EVISION

ISTORY

................................................................................................... 91

1 Introduction

Welcome to Korenix JetI/O 6500 Series Industrial Managed Ethernet I/O Server User

Manual. Following topics are covered in this chapter:

1.1 Overview of JetI/O 6500 Series

1.2 Package Checklist

1.3 JetI/O 6510 Introduction

1.4 JetI/O 6510 Product Specification

1.1 Overview of JetI/O 6500 Series

JetI

/O 6500 series is a series of Managed Ethernet I/O modules for distributive monitoring

and controls. The JetI/O 6500 series equipped with one Ethernet port and multiple channels

Analog Input/Output, Digital Input/Output and temperature measurement connectors. Thus users

can easily perform I/O data collecting, status changing, automatically activate events…

through the Ethernet network. JetI/O 6500 series provides Windows Utilities, and SNMP for

configuration. And support Modbus/TCP protocol, OPC Server for Modbus/TCP, thus user can

easily monitor and control the remote I/O devices and combine the JetI/O with existed

HMI/SCADA package.

Naming Rule: JetI/O 65AB

A: Major Feature

1: Analog Input Series. Includes the RTD input, Thermocouple Input

2: Analog Output Series

3: Digital Input Series

4: Digital Output Series

5: Digital Input and Digital Output Series

B: Sequence Number

JetI/O 6500 Series includes:

JetI/O 6510: Intelligent 8-CH Analog Input Ethernet I/O Server

JetI/O 6511: Intelligent 8-CH Thermocouple Input Ethernet I/O Server

JetI/O 6512: Intelligent 4-CH RTD Input Ethernet I/O Server

JetI/O 6520: Intelligent 4-CH Analog Output Ethernet I/O Server

JetI/O 6550: Intelligent 14-CH DI and 8-CH DO Ethernet I/O Server

1.2 Package Checklist

Korenix JetI/O 6500 Series products are shipped with following items:

One Ethernet I/O Server

One attached DIN-Rail clip

Terminal Blocks for I/O and Power Input

Documentation and Software CD

Quick Installation Guide

If any of the above items are missing or damaged, please contact your local sales

representative.

1.3 JetI/O 6510 Introduction

JetI/O 6510 is an intelligent I/O Server equipped with one Ethernet port and 8

channels Analog Input connectors. JetI/O 6510 provides 16 bits resolution and high

accuracy for I/O data collecting. The analog input range can support from 150mV

to 10V and 20mA. The values are most adopted in the industrial environemnt.

JetI/O 6510 provides Windows Utilities, SNMP for configuration. Industrial Modbus/

TCP protocol and OPC Server driver for integrating JetI/O with existed HMI/SCADA.

Robust aluminum case with good heat dispersing and IP31 protection. With JetI/O

users can easily perform status monitoring and control the remote I/O devices.

1.4 JetI/O 6510 Product Specification

System Feature

CPU: 100MHZ, RISC-Based Network Protocols: IP, TCP, UDP, SNMP, HTTP,

BOOTP, DHCP, Modbus/TCP, OPC Server

SDRAM: 32K bytes Configuration: Windows Utility, SNMP, DHCP Client,

TFTP Server for firmware update

Flash ROM: 512K bytes Windows Utility: Block I/O Utility

EEPROM: 256 bytes OPC Server Utility: OPC Server for Modbus/TCP

Watchdog Timer: 1.0 sec H/W SNMP: MIB-II: System, SNMP Trap and Private MIB

LED: SNMP Trap Server: Up to 4 SNMP Trap Server

PWR: Power Input plugged and On (Red) I/O Rules: High-/Low- Voltage/Current alarms

RDY: System startup ready (Green)

Power Requirement

Network Interface

System Power: external unregulated +24V (18-32V)

Ethernet: IEEE 802.3 10Base-T Power Consumption: Max. 3.2W

IEEE 802.3u 100Base-TX

Mechanical

Connector: 1 * RJ-45, Auto MDI/MDI-X Dimensions: 120 (H) x 55 (W) x 75 (D)mm

Protection: Built-

in 1.5 KV magnetic isolation

protection Mounting: Din-Rail

LED: Material: Aluminum

Upper (LAN Activity): Orange ON & Blinking

Environmental

Lower (10M/100M): 10M: Green OFF, 100M:

Green ON Regulatory Approvals: CE, FCC Class A

PWR: Power On (Green) Operating Temperature: -25 ~ 70°C

RDY: System boot up Ready (Red), system

booting (No LED) Operating Humidity: 0 ~ 95% non-condensing

Network Protocols: IP, TCP, UDP,

SNMP, HTTP,

Telnet, BOOTP, DHCP Storage Temperature: -40 ~ 80°C

Analog Input

Warranty: 3 years

Input Channels: 8 Channels

Resolution: 16 bits

Input Range :

Voltage : ±10V, ±5V, ±1V, ±500mV, ±150mV

Current : ±20mA with external 125Ωresistor

Accuracy: ±0.05% of FSR ±1LSB

Sampling Rate: 10 samples/sec (total)

Input Impedance: 10M ohm

Calibration: On Board EEPROM

Isolation Voltage: 2500Vrms

2 Hardware Installation

This chapter includes hardware introduction, installation and configuration information.

Following topics are covered in this chapter:

2.1 Hardware Introduction

Dimension

Appearance

LED Indicators

2.2 Wiring Power Input

2.3 Wiring I/O Connectors

2.4 Wiring Ethernet Ports

2.5 DIN-Rail Mounting Installation

2.1 Hardware Introduction

Dimensions:

120 (H) x 55 (W) x 75 (D) mm

JetI/O 6510 Appearance:

LED Indicators:

System LED

PWR

Power Input plugged and On (Green)

RDY

System startup ready (Red)

Ethernet LED

Upper (LAN

Activity)

Orange On & Blinking

Lower(10M/100M)

10M (Green Off) /100M(Green ON

2.2 Wiring Power Input

Follow below steps to wire JetI/O DC power inputs.

1. Follow the pin assignment to insert the wires into the contacts on the terminal block

connector.

2. Tighten the wire-clamp screws to prevent DC wires from being loosened.

3. Connect to and turn on the power source. The suitable working voltage is 24VDC.

4. When the unit is ready, the PWR LED turns Greed, the RDY LED turns Red.

Note1: It is a good practice to turn off input and load power, and to unplug power terminal

block before making wire connections. Otherwise, your screwdriver blade can

inadvertently short your terminal connections to the grounded enclosure.

Note 2: The range of the suitable electric wire is from 12 to 24 AWG.

2.3 Wiring I/O Connectors

Follow the pin assignment to insert the wires into the front contacts on the terminal block

connector. Tighten the wire-clamp screws to prevent the I/O wires from being loosened.

The wiring diagram of the JetI/O 6510 is as below:

2.4 JetI/O 6510 Wiring Example

2.4.1 JetI/O 6510 analog Voltage input wiring example

2.4.2 JetI/O 6510 analog Current input wiring example

Pin No Description Pin No Description

V4+ Analog input CH4+ V0+ Analog input CH0+

V4- Analog input CH4- V0- Analog input CH0-

V5+ Analog input CH5+ V1+ Analog input CH1+

V5- Analog input CH5- V1- Analog input CH1-

V6+ Analog input CH6+ V2+ Analog input CH2+

V6- Analog input CH6- V2- Analog input CH2-

V7+ Analog input CH7+ V3+ Analog input CH3+

V7- Analog input CH7- V3- Analog input CH3-

2.5 Wiring Earth Ground

To ensure the system will not be damaged by noise or any electrical shock, we suggest

you to make exact connection with JetI/O products with Earth Ground.

On the bottom side of JetI/O 6500 Series, there is one power earth ground pin in the

Power Input terminal block.

2.6 Wiring Fast Ethernet Ports

JetI/O 6500 series includes 1 RJ45 Fast Ethernet ports. The fast Ethernet ports support

10Base-T and 100Base-TX, full or half duplex modes. The fast Ethernet port will

auto-detect the signal from connected devices to negotiate the link speed and duplex

mode. Auto MDI/MDIX allows users to connect another switch, hub or workstation without

changing straight through or crossover cables.

Connect one side of an Ethernet cable into the Ethernet port and connect the other side to

the attached switch or host. The link LED will light up when the cable is correctly

connected. Refer to the LED Indicators section for descriptions of each LED indicator.

Always make sure that the cable length between the 2 ends is less than 100 meters (328

feet).

The wiring cable types are as below.

10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable, EIA/TIA-568 100-ohm (100m)

100 Base-TX: 2-pair UTP/STP Cat. 5 cable, EIA/TIA-568 100-ohm (100m)

1000 Base-TX: 4-pair UTP/STP Cat. 5 cable, EIA/TIA-568 100-ohm (100m)

2.7 Din-Rail Mounting Installation

The DIN-Rail clip is already attached to the JetI/O 6500 Series when packaged. If the

DIN-Rail clip is not screwed on the JetI/O, follow the instructions and the figure below to

attach DIN-Rail clip to JetI/O.

Figure 1.



Insert the upper end of DIN-Rail clip into the back of DIN-Rail track from its

upper side.

Pin No Description

1(+24V) DC+24V Power Input

2(FGND ) Power Earth Ground

3(0V) Referenced Ground for Power Input

Andere Handbücher für JetI/O 6510

Inhaltsverzeichnis

Andere Korenix Server Handbücher

Korenix

Korenix JetI/O 6510 Bedienungsanleitung

Korenix

Korenix JetPort 5208 Bedienungsanleitung

Korenix

Korenix JetPort 5601 Bedienungsanleitung

Korenix

Korenix JetPort 5201 Bedienungsanleitung

Korenix

Korenix 5804 Bedienungsanleitung

Korenix

Korenix JetPort 5601 Bedienungsanleitung

Korenix

Korenix JetPort 5601 Bedienungsanleitung

Korenix

Korenix JetPort 5801 Bedienungsanleitung

Korenix

Korenix JetPort 5601 Bedienungsanleitung

Korenix

Korenix JetPort 5201 Bedienungsanleitung

Korenix

Korenix AnyBus-X Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung