Korenix JetNet 3005 Bedienungsanleitung
JetNet 3005/3008
Industrial Entry Level 5-port/8-port Ethernet
Rail Switch
User’s Manual
Rev.1.1
20-Jan-2005
Content
Introduction.........................................................1
Features...................................................................1
Package Checklist....................................................2
Hardware Description.........................................3
Dimensions ..............................................................3
Front Panel...............................................................3
Bottom View.............................................................5
Wiring the DC Power Inputs.....................................5
LED Indicators..........................................................6
Ports.........................................................................8
Cabling.....................................................................9
DIN-Rail Mounting.................................................. 10
Wall Mounting ........................................................12
Hardware Installation........................................13
Installation and Testing..........................................13
Introduction
Industrial environments are usually more demanding than office environments.
Harsh temperature conditions, vibration, dust, etc. all put a test on the quality and
reliability of your switches. To survive harsh industrial environments, Korenix
provides you with JetNet 3005/3008 Series, an Industrial 5-port/8-port Entry Level
Ethernet Rail Switch. JetNet 3005/3008 Industrial Entry Level 5-port/8-port
Ethernet Rail Switch is a cost-effective solution ideal for your industrial
applications in harsh environments. JetNet 3005/3008 not only gives you high
speed data transmission over an Ethernet network, but also provides redundant
power inputs and reverse polarity protection. In addition, JetNet 3005/3008 uses a
IP30 aluminum case, and has passed several safety certifications, ensuring
customers a cost-effective, safe, and reliable industrial applications.
Features
5-port /8-port 10/100T(X) industrial switch
Supports store-and-Forward switching architecture
Supports IEEE 802.3 10Base-T, 802.3u 100Base-TX standard
Supports auto MDI/MDI-X function
JetNet 3005: 512 KB/JetNet 3008:1024KB embedded memory
Supports IEEE 802.3x flow control
¾Flow control for full-duplex mode
¾Back pressure for half-duplex mode
Provides redundant dual power inputs
Aluminum case with IP30 protection
JetNet 3005:1K /JetNet 3008:2K MAC address table
DIN-Rail and wall mountable design
1
Package Checklist
JetNet 3005/3008 Industrial 5-port/8-port Entry Level Ethernet Rail Switches are
packaged with the following items:
JetNet 3005/3008 Industrial Entry Level 5-port/8-port Ethernet Rail Switch
One DIN-Rail clip (attached with the JetNet 3005/3008)
One wall mounting plate and six screws
User’s manual CD-ROM
Quick Installation Guide
JetNet 3005/3008 Industrial Entry Level User’s Manual CD-ROM Quick Installation Guide
5-port/8-portEthernetRailSwitch
WallMountingPlate Screws DIN-RailClip
Contact your sales representative if any item is missing or damaged.
2
Hardware Description
Dimensions
JetNet 3005/3008 Industrial Entry Level 5-port/8-port Ethernet Rail Switch
dimensions (W x H x D) are 54mm x 135mm x 105mm
FrontPanel
The Front Panel of the JetNet 3005 Industrial Entry Level 5-port Ethernet Rail
Switch is shown in Figure A.
LED Indicators
UTP Port
Figure A. Front Panel of the JetNet3005 Industrial Entry Level 5-port Ethernet Rail Switch
3
The Front Panel of the JetNet 3008 Industrial Entry Level 8-port Ethernet Rail
Switch is shown in Figure A.
LED Indicators
UTP Port
Figure A. Front Panel of the JetNet3008 Industrial Entry Level 8-port Ethernet Rail Switch
4
Bottom View
The bottom view of the JetNet 3005/3008 Industrial Entry Level 5-port/8-port
Ethernet Rail Switch consists of one terminal block connector with two DC power
inputs and one DC IN power jack for an additional AC/DC power adapter.
Figure B. Bottom view of the JetNet 3005/3008 Industrial Entry Level 5-port/8-port Ethernet Rail Switch
Wiring the DC Power Inputs
Follow the steps below to wire JetNet3005/3008’s dual DC power inputs.
[Note] The suitable electric wire ranges from 12 to 24 AWG.
V- V+V- V+
1. Insert the positive and negative wires into the V+ and V-
contacts respectively of the terminal block connector
2. Tighten the wire-clamp screws to prevent the DC wires
from being loosened.
5
[Note] The additional power jack is designed for office use.
LEDIndicators
There are 5 diagnostic LEDs and 8 Port LEDs located on the Front panel of JetNet
3005 Industrial Ethernet Rail Switch. These LED indicators provide administrators
with real-time system status. Table 1 gives descriptions of the function of each
LED indicator.
LED Status Description
Green Power is on.
PWR Off No power is being supplied.
Green Power is on.
PWR 1 Off No power is being supplied.
Green Power is on.
PWR 2
Off No power is being supplied.
Green A network device is detected.
Blinks The port is transmitting or receiving
packets from the TX device.
LNK/ACT of Port5
Off No device is attached.
Orange The port is operating in full-duplex
mode.
Blinks Collision of packets occurs.
FDX/COL of Port5
Off The port is in half-duplex mode or
no device is attached.
6
Port LED Status Description
Orange The port is operating in full-duplex
mode.
Blinking
orange Collision of Packets occurs.
Off The port is in half-duplex mode or
no device is attached.
Green A network device is detected.
Blinking
green
The port is transmitting or receiving
packets from the TX device.
Port Status (Port 1
to Port 4)
Off No device is attached.
Table 1
There are 7 diagnostic LEDs and 12 Port LEDs located on the Front panel of
JetNet 3008 Industrial Ethernet Rail Switch. These LED indicators provide
administrators with real-time system status. Table 2 gives descriptions of the
function of each LED indicator.
LED Status Description
Green Power is on.
PWR Off No power is being supplied.
Green Power is on.
PWR 1 Off No power is being supplied.
Green Power is on.
PWR 2
Off No power is being supplied.
LNK/ACT of Port Green A network device is detected.
7
Blinks The port is transmitting or receiving
packets from the TX device.
7/port8
Off No device is attached.
Orange The port is operating in full-duplex
mode.
Blinks Collision of packets occurs.
FDX/COL of Port
Port 7/8
Off The port is in half-duplex mode or
no device is attached.
Port LED Status Description
Orange The port is operating in full-duplex
mode.
Blinking
orange Collision of Packets occurs.
Off The port is in half-duplex mode or
no device is attached.
Green A network device is detected.
Blinking
green
The port is transmitting or receiving
packets from the TX device.
Port Status (Port 1
to Port 6)
Off No device is attached.
Table 2
Ports
RJ-45 ports (Auto MDI/MDIX): JetNet 3005/3008 has five 10/100 Mbps
auto-sensing ports for 10Base-T or 100Base-TX device connection. The UTP
ports will auto-detect 10Base-T and 100Base-TX connections. Auto MDI/MDIX
allows users to connect another switch or workstation without changing straight
through or crossover cabling. See Figure C and C-1 for the schematic diagram of
straight through and crossover cabling.
8
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Korenix Schalten Handbücher
Korenix
Korenix JetNet 6059G Bedienungsanleitung
Korenix
Korenix JetNet 5310G Bedienungsanleitung
Korenix
Korenix JetNet 5728G series Bedienungsanleitung
Korenix
Korenix JetNet 2005f Bedienungsanleitung
Korenix
Korenix JetNet 7014G Series Bedienungsanleitung
Korenix
Korenix JetNet 5210G Bedienungsanleitung
Korenix
Korenix JetNet 6710G Bedienungsanleitung
Korenix
Korenix JetNet 3705 Series Bedienungsanleitung
Korenix
Korenix JetNet 3018G Series Bedienungsanleitung
Korenix
Korenix JetNet 2205 Series Bedienungsanleitung
Korenix
Korenix JetNet 7310G Series Bedienungsanleitung
Korenix
Korenix JetNet 4000 Bedienungsanleitung
Korenix
Korenix JetNet 6828Gf-2AC Bedienungsanleitung
Korenix
Korenix JetNet 7850G-2XG Bedienungsanleitung
Korenix
Korenix JetNet 7628X Series Bedienungsanleitung
Korenix
Korenix JetNet 3010G Series Bedienungsanleitung
Korenix
Korenix JetNet 6710G Bedienungsanleitung
Korenix
Korenix JetNet 3810G Series Bedienungsanleitung
Korenix
Korenix JetNet3008G V2 Bedienungsanleitung
Korenix
Korenix JetNet 4508 Bedienungsanleitung
