Korg DS-DAC-10R Bedienungsanleitung

DS-DAC-10R

OWNER'S MANUAL

Before you connect this device

In order to use the DS-DAC-10R on Windows (ASIO), you'll need to make driver seings.

It is important that you do not connect the DS-DAC-10R to your computer before you have

installed the driver.

Carefully read the section entitled “Download and Install,” and download and install the

Setup program before you connect the DS-DAC-10R to your computer.

E 3

4015-2 Yanokuchi, Inagi-city, Tokyo 206-0812 Japan http://www.korg.com

Contents

Introduction------------------------------------------------------------ 2

Features ------------------------------------------------------------- 2

Operating requirements----------------------------------------- 2

Download and Install ----------------------------------------------- 3

Windows users ---------------------------------------------------- 3

Installing the ASIO driver/AudioGate ------------------- 3

Mac OS users------------------------------------------------------ 6

Installing the AudioGate------------------------------------ 6

KORG 2ch 1bit Audio Driver Control Panel settings---- 7

Operation --------------------------------------------------------------- 8

Front and rear panels -------------------------------------------- 8

Preparations-------------------------------------------------------- 8

Basic operation---------------------------------------------------10

DSD native playback via Windows (ASIO) -----------10

DSD native playback via Mac (Core Audio)----------12

DSD recording (Recording using AudioGate) -------14

DS-DAC-10R Setting Tool --------------------------------15

Troubleshooting-----------------------------------------------------16

Specications--------------------------------------------------------18

Published 01/2020

Introduction

Features

The DS-DAC-10R is a USB DAC/ADC that supports 1-bit DSD native playback/record* on

Windows (ASIO/WDM) or Mac (Core Audio).

By using it in conjunction with the AudioGate4 HIGH RESOLUTION MUSIC PLAYER ap-

plication, you can enjoy native playback/record of high-quality 1-bit DSD sound.

* Use AudioGate for DSD native playback/recording. On Windows, this may also be pos-

sible with applications that support ASIO 2.1 DSD.

Supported input:

PCM 44.1 kHz–192 kHz, 1-bit DSD 2.8224 MHz, 5.6448 MHz, Analog signal

Supported audio drivers:

ASIO, WDM, Core Audio

Operating requirements

Windows

Operating system:

Windows 7 Service Pack 1 (32 bit, 64 bit), Windows 8.1 (32 bit, 64 bit)

Windows 10 (32 bit, 64 bit)

CPU: Intel® Core™ Processors 2.6 GHz or higher (base or max)

*Intel Core i3 or beer recommended

*DSD real-time conversion playback between 2.8 MHz and 5.6 MHz requires

3.1 GHz or higher.

RAM: 4 GB or more

Mac OS

Operating system:

macOS 10.11–10.14

CPU: Intel® Core™ Processors 2.6 GHz or higher (base or max)

*Intel Core i3 or beer recommended

*DSD real-time conversion playback between 2.8 MHz and 5.6 MHz requires

3.1 GHz or higher.

RAM: 4 GB or more

Download and Install

Windows users

Use the KORG AudioGate and USB Audio Device Setup program to install the ASIO

driver and AudioGate.

Do not connect the DS-DAC-10R to your computer before you’ve nished installing

the driver. If you’ve already connected it, disconnect it; then reconnect it after you’ve

nished installing the driver.

Installing the ASIO driver/AudioGate

Access the following AudioGate 4 download page:

hp://www.korg.com/products/audio/audiogate4/download.php

Choose “AudioGate and USB Audio Device Setup,” and press the Windows version of

download buon to download the setup program.

Decompress the downloaded .zip le. In the “KORG AudioGate and USB Audio Device

Setup” folder, run Setup. The KORG AudioGate and USB Audio Device Setup panel

appears.

Click “Install DS-DAC-10R Driver” to install the ASIO driver. (refer to “• ASIO driver

installation procedure” on page 4)

If you want to install AudioGate, click “Install AudioGate” in the KORG AudioGate

and USB Audio

Device Setup panel.

Carefully read “Activating AudioGate” which appears during installation, and then

complete the installation.

Click “Finish” to exit the setup program.

If you're recording with an application other than AudioGate, you'll need to use the

“DS-DAC-10R Seing Tool” to set the input level. Click “Install the DS-DAC-10R Set-

ting Tool” to install it.

• ASIO driver installation procedure

Do not connect the DS-DAC-10R to your computer before you’ve nished installing

the driver. If you’ve already connected it, disconnect it; then reconnect it after you’ve

nished installing the driver.

The installation screens shown on your computer may differ somewhat depending on

your Windows version and system, but the procedure is the same. The explanation that

follows will show typical screens in Windows 7.

If, during installation, a message appeared to conrm whether or not to continue the in-

stallation, click [Install].

In the KORG AudioGate and USB Audio Device Setup panel that you downloaded,

click “Install DS-DAC-10R Driver” to start the installer.

In the language selection menu, choose English; click [OK].

The dialog box will appear; click [Next >].

If you accept the license agreement, click [Next (N) >].

Click [Install] to begin installation.

If a security warning appears, click [Install].

Preparations for installation are now complete. Click [Finish] to exit the installer.

Connect the DS-DAC-10R to your computer.

Wait until Windows displays the message “The device driver software was installed

correctly.”

Mac OS users

Use the KORG AudioGate and USB Audio Device Setup program to install AudioGate.

If you're using AudioGate, it is not necessary to install the driver.

Installing the AudioGate

Access the following AudioGate 4 download page:

hp://www.korg.com/products/audio/audiogate4/download.php

Choose “AudioGate and USB Audio Device Setup Download,” and press the Mac ver-

sion of download buon to download the setup program.

Open the .dmg le. In the “KORG AudioGate and USB Audio Device Setup” folder,

run Setup. The KORG AudioGate and USB Audio Device Setup panel appears.

Click “Install AudioGate” in the KORG AudioGate and USB Audio Device Setup pan-

el.

Carefully read “Activating AudioGate” which appears during installation, and then

complete the installation.

Click “Finish” to exit the setup program.

If you’re recording with an application other than AudioGate, you’ll need to use the

“DS-DAC-10R Seing Tool” to set the input level. Click “Install the DS-DAC-10R Set-

ting Tool” to install it.

KORG 2ch 1bit Audio Driver Control Panel settings

The Mac version of the control panel does not allow you to directly change the Sample

Rate. You can make these changes via AudioGate or from the Audio MIDI seings of

your Mac.

In the Windows start menu Control Panel, view all control panel items, and click “KORG

2ch 1bit Audio Driver” DS-DAC Audio I/O Driver Control Panel to open it; the following

control panel appears:

Buer Size

Selects the buer size. Moving the slider toward the left decreases the buer size, and

moving it toward the right increases the size.

* Increasing the buer size increases the time dierence (latency) between the direct

sound and the monitored sound, but allows you to record safely without noise oc-

curring.

Normally, including while recording vinyl records, you should leave this at the

maximum seing. Only if you are bothered by latency, such as when making a live

recording, adjust the buer size without allowing noise to occur.

Sampling Rate

Species the sampling rate. Choose from 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4

kHz, 192 kHz. If you’re using the DS-DAC-10R with WDM (WASAPI/Direct Sound),

make the seing here.

Operation

Front and rear panels

Phono

ground terminal

Headphones jack

Headphone volume Knob

Indicator

Line output jacks

USB port

Line input/Phono jacks

Preparations

When driver installation is completed, use a USB cable to connect the DS-DAC-10R to your

computer, and make preparations for listening to an audio le on your computer.

After connecting the USB cable and until the DS-DAC-10R's system setup has completed,

the indicator alternately blinks green and blue.

When the indicator changes to being steadily lit, start AudioGate.

Use the included USB cable to connect the unit to your computer and to verify that it’s

working.

The DS-DAC-10R operates on USB bus power. It does not need an AC adaptor or any

other external power supply.

Whenever possible, connect this unit directly to a USB port on your computer. If you

cannot avoid using a USB hub, you should use a USB hub that has its own power sup-

ply. A bus-powered USB hub may be unable to supply enough power.

If you want to listen through headphones, connect your headphones to the headphone

jack.

If you want to connect an amp and speakers for listening, connect the line out jacks of

the DS-DAC-10R to your system using the appropriate cables.

If you want to record, connect the output cable of your analog device to the line input/

phono jacks.

Check the USB port connection. The indicator is lit green if the connection from your

computer to the DS-DAC-10R is enabled.

The color of the indicator changes depending on the system and application seings,

and on the sampling rate of the audio le that you're playing back.

Sampling rate 44.1 kHz

48 kHz

88.2 kHz

96 kHz

176.4 kHz

192 kHz

2.8 MHz 5.6 MHz

Indicator Green Purple White Light blue Dark blue

When in record-standby mode, the sampling rate and the red indicator are lit alter-

nately, and during recording the indicator is lit red.

Basic operation

DSD native playback via Windows (ASIO)

Use the AudioGate and USB Audio Device Setup program to install AudioGate (refer

to “Installing the ASIO driver/AudioGate” on page 3).

Connect the DS-DAC-10R to your computer, and then start AudioGate.

If you start AudioGate without the DS-DAC-10R connected, license verication will be

completed when you connect the DS-DAC-10R.

From the menu, choose [Edit]-[Preferences...], and click the [Audio Devices] tab.

In [Driver Type], choose “ASIO.”

In [Output Device Name], choose “KORG 2ch 1bit Audio Device.”

Set [Sample Rate] to “Auto” or to “5.6 MHz” or “2.8 MHz.”

Andere Handbücher für DS-DAC-10R

Inhaltsverzeichnis

Andere Korg Soundkarte Handbücher

Korg

Korg EXBP Dual MP3 Bedienungsanleitung

Beliebte Soundkarte Handbücher anderer Marken

PCchips

PCchips CMI8330 Bedienungsanleitung

Creative

Creative Sound BlasterX G5 SB1700 Bedienungsanleitung

IBM

IBM Music Feature Card Bedienungsanleitung

Diamond Multimedia

Diamond Multimedia Xtreme Sound Bedienungsanleitung

Digigram

Digigram VX222v2 Bedienungsanleitung

Pure Speed

Pure Speed DSU6000 Bedienungsanleitung

Philips

Philips Seismic Edge PSC704 Bedienungsanleitung

ADDAC System

ADDAC System ADDAC604 Bedienungsanleitung

Asus

Asus Audio Card Xonar D2 Bedienungsanleitung

Soundwave

Soundwave 7.1 Bedienungsanleitung

Creative

Creative Sound Blaster Pro Bedienungsanleitung

Digigram

Digigram VX222-Mic Bedienungsanleitung

HRT

HRT LineStreamer+ Bedienungsanleitung

ST AEKD-STEREOAVAS Bedienungsanleitung

AuviTran

AuviTran AVY16-ES100 Bedienungsanleitung

Creative

Creative Sound BLASTER Audige Rx SB1550 Bedienungsanleitung

IQaudIO

IQaudIO PI-DAC+ Bedienungsanleitung

VideoLogic

VideoLogic SonicVortex2 Bedienungsanleitung